Hi, I'm using a Huawei E303 dongle to connect to kannel on ubuntu 14.04.
Following is my wvdialconf output.. Modem Port Scan<*1>: S0 S1 S2 S3 S4 S5 S6 S7 Modem Port Scan<*1>: S8 S9 S10 S11 S12 S13 S14 S15 Modem Port Scan<*1>: S16 S17 S18 S19 S20 S21 S22 S23 Modem Port Scan<*1>: S24 S25 S26 S27 S28 S29 S30 S31 ttyUSB0<*1>: ATQ0 V1 E1 -- OK ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- COMMAND NOT SUPPORT ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: huawei ttyUSB0<*1>: Speed 9600: AT -- OK ttyUSB0<*1>: Max speed is 9600; that should be safe. ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyUSB2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyUSB2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud ttyUSB2<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. ttyUSB3<*1>: ATQ0 V1 E1 -- OK ttyUSB3<*1>: ATQ0 V1 E1 Z -- OK ttyUSB3<*1>: ATQ0 V1 E1 S0=0 -- OK ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- COMMAND NOT SUPPORT ttyUSB3<*1>: Modem Identifier: ATI -- Manufacturer: huawei ttyUSB3<*1>: Speed 9600: AT -- OK ttyUSB3<*1>: Max speed is 9600; that should be safe. ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK Found a modem on /dev/ttyUSB0. Modem configuration written to create. ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2" ttyUSB3<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2" When I use "ATQ0 V1 E1 S0=0 &C1 &D2" as init-string to connect to the dongle it says AT+IFC=2,2^M command not supported, cannot enable hardware handshake How do I overcome this issue. Thank you very much Regards, Pamod
