On 2020/02/19 19:15:01, Andrija Panic <[email protected]> wrote:
> Hi there,
>
> I don't get what is installed inside what (KVM vs VirtualBox)?
>
> Why don't you take a look into ACS Quick install guide which requires only
> a single host (your physical KVM host would do fine) -
> http://docs.cloudstack.apache.org/en/latest/quickinstallationguide/qig.html -
> you can go with ACS 4.13 (this guide is for 4.11) - there are 3 things that
> needs change:
> - do NOT add the mysql repo - but instead install Epel repo which will
> provide the needed mysql-connector-python (rmost recent versions of it from
> the MysQL repo are incompatible with ACS)
> - use 4.13 in ACS repo
> - use systemVM template 4.11.3 (instead of 4.11.2) when preseeding it (just
> replace "4.11.2" with "4.11.3" inside the section
> http://docs.cloudstack.apache.org/en/latest/quickinstallationguide/qig.html#system-template-setup
> )
>
> Cheers
> Andrija
>
> On Wed, 19 Feb 2020 at 18:01, Marciel Bonamigo <
> [email protected]> wrote:
>
> > Hello, I'm setting up a test lab with ACS 4.13 and KVM at centos7
> >
> > Scenario:
> > -KVM physical server
> > -ACS is in the Virtual Box
> >
> > After all the configurations when starting SSVM it takes a long time and
> > when I start I can't access them by any IP address, because for some reason
> > these SSVM are not going out to the internet.
> >
> > KVM Network Settings:
> >
> > cloudbr0:
> > DEVICE = cloudbr0
> > TYPE = Bridge
> > ONBOOT = yes
> > BOOTPROTO = none
> > IPADDR = 172.26.0.222
> > GATEWAY = 172.26.0.1
> > NETMASK = 255.255.255.0
> > USERCTL = no
> >
> > cloudbr1:
> > DEVICE = cloudbr1
> > TYPE = Bridge
> > ONBOOT = yes
> > BOOTPROTO = none
> > IPV6INIT = no
> > IPV6_AUTOCONF = no
> >
> > enp6s0:
> > DEVICE = enp6s0
> > ONBOOT = yes
> > HOTPLUG = no
> > BOOTPROTO = none
> > TYPE = Ethernet
> > BRIDGE = cloudbr0
> >
> > enp6s0.300:
> > DEVICE = enp6s0.300
> > ONBOOT = yes
> > HOTPLUG = no
> > BOOTPROTO = none
> > TYPE = Ethernet
> > VLAN = yes
> > BRIDGE = cloudbr1
> >
> > ACS Network Settings in Virtual BOx:
> > Adapter A connected in Bridge mode, so that it stays on the same KVM
> > network as on 172.26.0.0/24
> > _____________________________________
> >
> > My question is how to configure the Public network so that SSVM can start
> > correctly.
> >
> > Anyone who could help I appreciate it.
> >
> >
>
> --
>
> Andrija Panić
>
________________________
Thank you for the informations, Andrija Panić.
I installed and ACS on the same host as the KVM, I did all the configurations
and the SSVM started, connected to them by ssh.
I am now having trouble adding an iso.
I realized that when I connect to SSVM I am not responding to DNS.
My resolv.conf is:
nameserver 8.8.8.8
nameserver 1.1.1.1
Any tips on how to add the ISo?
