i did follow the wiki script. I did an installation of the letsencrypt certicates before and it seems to work. Perhaps I have to redo it.
right now i#m stopped at saving iptables-rules ---------------------- sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- anywhere anywhere tcp dpt:3478 ACCEPT udp -- anywhere anywhere udp dpt:3478 ACCEPT tcp -- anywhere anywhere tcp dpt:5443 ACCEPT tcp -- anywhere anywhere tcp dpt:8888 ACCEPT udp -- anywhere anywhere multiport dports 49152:65535 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere multiport dports 49152:65535 ------------------------------------ sudo service iptables save iptables: unrecognized service !!!!!!!!!!!! thats the problem !!!!!! ---------------------------------- sudo apt list --installed | grep table WARNING: apt does not have a stable CLI interface. Use with caution in scripts. iptables/bionic,bionic,now 1.6.1-2ubuntu2 amd64 [installiert] libevent-core-2.1-6/bionic,bionic,now 2.1.8-stable-4build1 amd64 [Installiert,automatisch] libevent-extra-2.1-6/bionic,bionic,now 2.1.8-stable-4build1 amd64 [Installiert,automatisch] libevent-openssl-2.1-6/bionic,bionic,now 2.1.8-stable-4build1 amd64 [Installiert,automatisch] libevent-pthreads-2.1-6/bionic,bionic,now 2.1.8-stable-4build1 amd64 [Installiert,automatisch] libxtables12/bionic,bionic,now 1.6.1-2ubuntu2 amd64 [installiert] ------------------------------------- sudo apt list --installed | grep -iE ".*ufw.*" WARNING: apt does not have a stable CLI interface. Use with caution in scripts. thanks again ... On 27/04/2020 20:42, Juan Antonio Moreno Carmona wrote: > You should install and configure your own turn server on the same > machine you run openmeetings. It's not difficult. > > Regards. > > El 27/4/20 a las 19:47, kaffeesurrogat escribió: >> Should I setup my own machine or is it save to use a public one ? >> >> On 27/04/2020 19:41, kaffeesurrogat wrote: >>> I didn't configure a STUN, is that the problem? Which server do you >>> recommend for being in germany ? >>> >>> >>> >>> On 27/04/2020 19:25, kaffeesurrogat wrote: >>>> Hey everybody, >>>> >>>> i just finished a testing session with OM 5.0.4 and two colleages. It >>>> didn't went well at all. >>>> Quite a few error messages popped up in the middle of the session, >>>> uploading of docx did not work, giving or withdrawing permissions to >>>> draw on the white board did fail or failed not. >>>> As my colleages logged in, they showed up twice in the user panel >>>> on the >>>> right sight. I've been the moderator, my colleagues the "users". >>>> After a short while and a couple of disconnections, I could not >>>> re-enter >>>> the room because it was full. I've limited the room capacity to 6 >>>> people. >>>> >>>> >>>> Restarting Openmeetings and KMS reentering the room for all of us, >>>> cleared the problem for a short while. >>>> >>>> >>>> The session was ended by a browser message, that the connection was >>>> lost. I've attached the the logfile from this sessions. You will find >>>> quite a few messages in there. I don't know, which one is really >>>> important, >>>> thus I send all of them, replacing personal information ..... >>>> >>>> >>>> Many thanks in advance, >>>> >>>> kaffeesurrogat >>>> >>>> it is quite big, sorry for that ... >>>>
