Use EHCI MXC configuration options for i.MX25.
Signed-off-by: Benoît Thébaudeau <benoit.thebaud...@advansee.com>
Cc: Marek Vasut <ma...@denx.de>
Cc: Stefano Babic <sba...@denx.de>
Cc: Matthias Weisser <weiss...@arcor.de>
---
Changes for v2: None.
.../drivers/usb/host/ehci-mxc.c | 71 +++++++++++++++++---
.../include/configs/zmx25.h | 6 +-
2 files changed, 66 insertions(+), 11 deletions(-)
diff --git u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mxc.c
u-boot-usb-76454b2/drivers/usb/host/ehci-mxc.c
index e21f2c5..711c4a7 100644
--- u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mxc.c
+++ u-boot-usb-76454b2/drivers/usb/host/ehci-mxc.c
@@ -28,10 +28,21 @@
#define USBCTRL_OTGBASE_OFFSET 0x600
-#define MX25_USB_CTRL_IP_PUE_DOWN_BIT (1<<6)
-#define MX25_USB_CTRL_HSTD_BIT (1<<5)
-#define MX25_USB_CTRL_USBTE_BIT (1<<4)
-#define MX25_USB_CTRL_OCPOL_OTG_BIT (1<<3)
+#define MX25_OTG_SIC_SHIFT 29
+#define MX25_OTG_SIC_MASK (0x3 << MX25_OTG_SIC_SHIFT)
+#define MX25_OTG_PM_BIT (1 << 24)
+#define MX25_OTG_PP_BIT (1 << 11)
+#define MX25_OTG_OCPOL_BIT (1 << 3)
+
+#define MX25_H1_SIC_SHIFT 21
+#define MX25_H1_SIC_MASK (0x3 << MX25_H1_SIC_SHIFT)
+#define MX25_H1_PP_BIT (1 << 18)
+#define MX25_H1_PM_BIT (1 << 8)
+#define MX25_H1_IPPUE_UP_BIT (1 << 7)
+#define MX25_H1_IPPUE_DOWN_BIT (1 << 6)
+#define MX25_H1_TLL_BIT (1 << 5)
+#define MX25_H1_USBTE_BIT (1 << 4)
+#define MX25_H1_OCPOL_BIT (1 << 2)
#define MX31_OTG_SIC_SHIFT 29
#define MX31_OTG_SIC_MASK (0x3 << MX31_OTG_SIC_SHIFT)
@@ -51,12 +62,56 @@ static int mxc_set_usbcontrol(int port, unsigned int flags)
{
unsigned int v;
-#if defined(CONFIG_MX25)
- v = MX25_USB_CTRL_IP_PUE_DOWN_BIT | MX25_USB_CTRL_HSTD_BIT |
- MX25_USB_CTRL_USBTE_BIT | MX25_USB_CTRL_OCPOL_OTG_BIT;
-#elif defined(CONFIG_MX31)
v = readl(IMX_USB_BASE + USBCTRL_OTGBASE_OFFSET);
+#if defined(CONFIG_MX25)
+ switch (port) {
+ case 0: /* OTG port */
+ v &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PM_BIT | MX25_OTG_PP_BIT |
+ MX25_OTG_OCPOL_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX25_OTG_PM_BIT;
+
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MX25_OTG_PP_BIT;
+
+ if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+ v |= MX25_OTG_OCPOL_BIT;
+
+ break;
+ case 1: /* H1 port */
+ v &= ~(MX25_H1_SIC_MASK | MX25_H1_PM_BIT | MX25_H1_PP_BIT |
+ MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT
|
+ MX25_H1_IPPUE_DOWN_BIT | MX25_H1_IPPUE_UP_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_H1_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX25_H1_PM_BIT;
+
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MX25_H1_PP_BIT;
+
+ if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+ v |= MX25_H1_OCPOL_BIT;
+
+ if (!(flags & MXC_EHCI_TTL_ENABLED))
+ v |= MX25_H1_TLL_BIT;
+
+ if (flags & MXC_EHCI_INTERNAL_PHY)
+ v |= MX25_H1_USBTE_BIT;
+
+ if (flags & MXC_EHCI_IPPUE_DOWN)
+ v |= MX25_H1_IPPUE_DOWN_BIT;
+ if (flags & MXC_EHCI_IPPUE_UP)
+ v |= MX25_H1_IPPUE_UP_BIT;
+
+ break;
+ default:
+ return -EINVAL;
+ }
+#elif defined(CONFIG_MX31)
switch (port) {
case 0: /* OTG port */
v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
diff --git u-boot-usb-76454b2.orig/include/configs/zmx25.h
u-boot-usb-76454b2/include/configs/zmx25.h
index 447683a..e9216d9 100644
--- u-boot-usb-76454b2.orig/include/configs/zmx25.h
+++ u-boot-usb-76454b2/include/configs/zmx25.h
@@ -109,9 +109,9 @@
#define CONFIG_USB_EHCI /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_MXC
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORT 2
-#define CONFIG_MXC_USB_PORTSC 0xC0000000
-#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_MXC_USB_PORT 1
+#define CONFIG_MXC_USB_PORTSC MXC_EHCI_MODE_SERIAL
+#define CONFIG_MXC_USB_FLAGS (MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN)
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
