Signed-off-by: Troy Kisky <troy.ki...@boundarydevices.com>
---
board/freescale/mx6qsabrelite/mx6qsabrelite.c | 235 ++++++-------------------
board/freescale/mx6qsabrelite/pads.h | 172 ++++++++++++++++++
2 files changed, 229 insertions(+), 178 deletions(-)
create mode 100644 board/freescale/mx6qsabrelite/pads.h
diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
index 4b4e89b..454972c 100644
--- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
+++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
@@ -26,6 +26,8 @@
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6x_pins.h>
+#include <asm/arch/mx6dl_pins.h>
+#include <asm/arch/sys_proto.h>
#include <asm/errno.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
@@ -38,162 +40,52 @@
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
-#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | \
- PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define BUTTON_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+#ifdef CONFIG_MX6Q
+#include "pads.h"
+#endif
+#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
+#define FOR_DL_SOLO
+#include "pads.h"
+#endif
-int dram_init(void)
+int cpu_is_mx6q(void)
{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
-
- return 0;
+ return (get_cpu_rev() >> 12) == MXC_CPU_MX6Q;
}
-iomux_v3_cfg_t uart1_pads[] = {
- MX6Q_PAD_SD3_DAT6__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6Q_PAD_SD3_DAT7__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t uart2_pads[] = {
- MX6Q_PAD_EIM_D26__UART2_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6Q_PAD_EIM_D27__UART2_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-/* I2C1, SGTL5000 */
-struct i2c_pads_info i2c_pad_info0 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_EIM_D21__I2C1_SCL | PC,
- .gpio_mode = MX6Q_PAD_EIM_D21__GPIO_3_21 | PC,
- .gp = IMX_GPIO_NR(3, 21)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_EIM_D28__I2C1_SDA | PC,
- .gpio_mode = MX6Q_PAD_EIM_D28__GPIO_3_28 | PC,
- .gp = IMX_GPIO_NR(3, 28)
- }
-};
-
-/* I2C2 Camera, MIPI */
-struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC,
- .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO_4_12 | PC,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO_4_13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-/* I2C3, J15 - RGB connector */
-struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_GPIO_5__I2C3_SCL | PC,
- .gpio_mode = MX6Q_PAD_GPIO_5__GPIO_1_5 | PC,
- .gp = IMX_GPIO_NR(1, 5)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_GPIO_16__I2C3_SDA | PC,
- .gpio_mode = MX6Q_PAD_GPIO_16__GPIO_7_11 | PC,
- .gp = IMX_GPIO_NR(7, 11)
- }
-};
+#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
+#ifdef CONFIG_MX6Q
+#define GET_MX6_REF(ref) (cpu_is_mx6q() ? mx6q_##ref : mx6dl_solo_##ref)
+#define IOMUX_SETUP(list) iomux_setup(mx6q_##list, ARRAY_SIZE(mx6q_##list), \
+ mx6dl_solo_##list, ARRAY_SIZE(mx6dl_solo_##list))
-iomux_v3_cfg_t usdhc3_pads[] = {
- MX6Q_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD3_DAT5__GPIO_7_0 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
+int iomux_setup(iomux_v3_cfg_t *mx6q_pad_list, int mx6q_pad_cnt,
+ iomux_v3_cfg_t *mx6dl_solo_pad_list, int mx6dl_solo_pad_cnt)
+{
+ int mx6q = cpu_is_mx6q();
+ iomux_v3_cfg_t *p = mx6q ? mx6q_pad_list : mx6dl_solo_pad_list;
+ int cnt = mx6q ? mx6q_pad_cnt : mx6dl_solo_pad_cnt;
-iomux_v3_cfg_t usdhc4_pads[] = {
- MX6Q_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6Q_PAD_NANDF_D6__GPIO_2_6 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
+ return imx_iomux_v3_setup_multiple_pads(p, cnt);
+}
-iomux_v3_cfg_t enet_pads1[] = {
- MX6Q_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- /* pin 35 - 1 (PHY_AD2) on reset */
- MX6Q_PAD_RGMII_RXC__GPIO_6_30 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 32 - 1 - (MODE0) all */
- MX6Q_PAD_RGMII_RD0__GPIO_6_25 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 31 - 1 - (MODE1) all */
- MX6Q_PAD_RGMII_RD1__GPIO_6_27 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 28 - 1 - (MODE2) all */
- MX6Q_PAD_RGMII_RD2__GPIO_6_28 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 27 - 1 - (MODE3) all */
- MX6Q_PAD_RGMII_RD3__GPIO_6_29 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
- MX6Q_PAD_RGMII_RX_CTL__GPIO_6_24 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 42 PHY nRST */
- MX6Q_PAD_EIM_D23__GPIO_3_23 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
+#else
+#define GET_MX6_REF(ref) (mx6dl_solo_##ref)
+#define IOMUX_SETUP(list) imx_iomux_v3_setup_multiple_pads( \
+ mx6dl_solo_##list, ARRAY_SIZE(mx6dl_solo_##list))
+#endif
+#else
-iomux_v3_cfg_t enet_pads2[] = {
- MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
+#define GET_MX6_REF(ref) (mx6q_##ref)
+#define IOMUX_SETUP(list) imx_iomux_v3_setup_multiple_pads( \
+ mx6q_##list, ARRAY_SIZE(mx6q_##list))
+#endif
-/* Button assignments for J14 */
-static iomux_v3_cfg_t button_pads[] = {
- /* Menu */
- MX6Q_PAD_NANDF_D1__GPIO_2_1 | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
- /* Back */
- MX6Q_PAD_NANDF_D2__GPIO_2_2 | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
- /* Labelled Search (mapped to Power under Android) */
- MX6Q_PAD_NANDF_D3__GPIO_2_3 | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
- /* Home */
- MX6Q_PAD_NANDF_D4__GPIO_2_4 | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
- /* Volume Down */
- MX6Q_PAD_GPIO_19__GPIO_4_5 | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
- /* Volume Up */
- MX6Q_PAD_GPIO_18__GPIO_7_13 | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
-};
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+ return 0;
+}
static void setup_iomux_enet(void)
{
@@ -203,30 +95,26 @@ static void setup_iomux_enet(void)
gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
- imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
+ IOMUX_SETUP(enet_pads1);
gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
/* Need delay 10ms according to KSZ9021 spec */
udelay(1000 * 10);
gpio_set_value(IMX_GPIO_NR(3, 23), 1);
- imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
+ IOMUX_SETUP(enet_pads2);
}
-iomux_v3_cfg_t usb_pads[] = {
- MX6Q_PAD_GPIO_17__GPIO_7_12 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
static void setup_iomux_uart(void)
{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
- imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+ IOMUX_SETUP(uart1_pads);
+ IOMUX_SETUP(uart2_pads);
}
#ifdef CONFIG_USB_EHCI_MX6
int board_ehci_hcd_init(int port)
{
- imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads));
+ IOMUX_SETUP(usb_pads);
/* Reset USB hub */
gpio_direction_output(IMX_GPIO_NR(7, 12), 0);
@@ -267,12 +155,10 @@ int board_mmc_init(bd_t *bis)
for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
switch (index) {
case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ IOMUX_SETUP(usdhc3_pads);
break;
case 1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+ IOMUX_SETUP(usdhc4_pads);
break;
default:
printf("Warning: you configured more USDHC controllers"
@@ -294,19 +180,10 @@ u32 get_board_rev(void)
}
#ifdef CONFIG_MXC_SPI
-iomux_v3_cfg_t ecspi1_pads[] = {
- /* SS1 */
- MX6Q_PAD_EIM_D19__GPIO_3_19 | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6Q_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6Q_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6Q_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
-};
-
void setup_spi(void)
{
gpio_direction_output(CONFIG_SF_DEFAULT_CS, 1);
- imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
- ARRAY_SIZE(ecspi1_pads));
+ IOMUX_SETUP(ecspi1_pads);
}
#endif
@@ -342,8 +219,7 @@ int board_eth_init(bd_t *bis)
static void setup_buttons(void)
{
- imx_iomux_v3_setup_multiple_pads(button_pads,
- ARRAY_SIZE(button_pads));
+ IOMUX_SETUP(button_pads);
}
#ifdef CONFIG_CMD_SATA
@@ -382,15 +258,17 @@ int board_early_init_f(void)
int board_init(void)
{
+ struct i2c_pads_info *p = GET_MX6_REF(i2c_pad_info);
+
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &p[0]);
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &p[1]);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &p[2]);
#ifdef CONFIG_CMD_SATA
setup_sata();
@@ -401,9 +279,10 @@ int board_init(void)
int checkboard(void)
{
- puts("Board: MX6Q-Sabre Lite\n");
-
- return 0;
+ puts("Board: MX");
+ puts(get_imx_type(get_cpu_rev() >> 12));
+ puts("-Sabre Lite\n");
+ return 0;
}
struct button_key {
diff --git a/board/freescale/mx6qsabrelite/pads.h
b/board/freescale/mx6qsabrelite/pads.h
new file mode 100644
index 0000000..e7ffe21
--- /dev/null
+++ b/board/freescale/mx6qsabrelite/pads.h
@@ -0,0 +1,172 @@
+#undef MX6PAD
+#undef MX6NAME
+
+#ifdef FOR_DL_SOLO
+#define MX6PAD(a) MX6DL_PAD_##a
+#define MX6NAME(a) mx6dl_solo_##a
+#else
+#define MX6PAD(a) MX6Q_PAD_##a
+#define MX6NAME(a) mx6q_##a
+#endif
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | \
+ PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define BUTTON_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+iomux_v3_cfg_t MX6NAME(uart1_pads)[] = {
+ MX6PAD(SD3_DAT6__UART1_RXD) | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6PAD(SD3_DAT7__UART1_TXD) | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t MX6NAME(uart2_pads)[] = {
+ MX6PAD(EIM_D26__UART2_TXD) | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6PAD(EIM_D27__UART2_RXD) | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+struct i2c_pads_info MX6NAME(i2c_pad_info)[] = {
+ {
+ /* I2C1, SGTL5000 */
+ .scl = {
+ .i2c_mode = MX6PAD(EIM_D21__I2C1_SCL) | PC,
+ .gpio_mode = MX6PAD(EIM_D21__GPIO_3_21) | PC,
+ .gp = IMX_GPIO_NR(3, 21)
+ },
+ .sda = {
+ .i2c_mode = MX6PAD(EIM_D28__I2C1_SDA) | PC,
+ .gpio_mode = MX6PAD(EIM_D28__GPIO_3_28) | PC,
+ .gp = IMX_GPIO_NR(3, 28)
+ }
+ }, {
+ /* I2C2 Camera, MIPI */
+ .scl = {
+ .i2c_mode = MX6PAD(KEY_COL3__I2C2_SCL) | PC,
+ .gpio_mode = MX6PAD(KEY_COL3__GPIO_4_12) | PC,
+ .gp = IMX_GPIO_NR(4, 12)
+ },
+ .sda = {
+ .i2c_mode = MX6PAD(KEY_ROW3__I2C2_SDA) | PC,
+ .gpio_mode = MX6PAD(KEY_ROW3__GPIO_4_13) | PC,
+ .gp = IMX_GPIO_NR(4, 13)
+ }
+ }, {
+ /* I2C3, J15 - RGB connector */
+ .scl = {
+ .i2c_mode = MX6PAD(GPIO_5__I2C3_SCL) | PC,
+ .gpio_mode = MX6PAD(GPIO_5__GPIO_1_5) | PC,
+ .gp = IMX_GPIO_NR(1, 5)
+ },
+ .sda = {
+ .i2c_mode = MX6PAD(GPIO_16__I2C3_SDA) | PC,
+ .gpio_mode = MX6PAD(GPIO_16__GPIO_7_11) | PC,
+ .gp = IMX_GPIO_NR(7, 11)
+ }
+ }
+};
+
+iomux_v3_cfg_t MX6NAME(usdhc3_pads)[] = {
+ MX6PAD(SD3_CLK__USDHC3_CLK) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD3_CMD__USDHC3_CMD) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD3_DAT0__USDHC3_DAT0) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD3_DAT1__USDHC3_DAT1) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD3_DAT2__USDHC3_DAT2) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD3_DAT3__USDHC3_DAT3) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD3_DAT5__GPIO_7_0) | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t MX6NAME(usdhc4_pads)[] = {
+ MX6PAD(SD4_CLK__USDHC4_CLK) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD4_CMD__USDHC4_CMD) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD4_DAT0__USDHC4_DAT0) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD4_DAT1__USDHC4_DAT1) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD4_DAT2__USDHC4_DAT2) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(SD4_DAT3__USDHC4_DAT3) | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6PAD(NANDF_D6__GPIO_2_6) | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t MX6NAME(enet_pads1)[] = {
+ MX6PAD(ENET_MDIO__ENET_MDIO) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(ENET_MDC__ENET_MDC) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_TXC__ENET_RGMII_TXC) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_TD0__ENET_RGMII_TD0) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_TD1__ENET_RGMII_TD1) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_TD2__ENET_RGMII_TD2) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_TD3__ENET_RGMII_TD3) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_TX_CTL__RGMII_TX_CTL) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(ENET_REF_CLK__ENET_TX_CLK) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* pin 35 - 1 (PHY_AD2) on reset */
+ MX6PAD(RGMII_RXC__GPIO_6_30) | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 32 - 1 - (MODE0) all */
+ MX6PAD(RGMII_RD0__GPIO_6_25) | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 31 - 1 - (MODE1) all */
+ MX6PAD(RGMII_RD1__GPIO_6_27) | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 28 - 1 - (MODE2) all */
+ MX6PAD(RGMII_RD2__GPIO_6_28) | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 27 - 1 - (MODE3) all */
+ MX6PAD(RGMII_RD3__GPIO_6_29) | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
+ MX6PAD(RGMII_RX_CTL__GPIO_6_24) | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 42 PHY nRST */
+ MX6PAD(EIM_D23__GPIO_3_23) | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t MX6NAME(enet_pads2)[] = {
+ MX6PAD(RGMII_RXC__ENET_RGMII_RXC) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_RD0__ENET_RGMII_RD0) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_RD1__ENET_RGMII_RD1) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_RD2__ENET_RGMII_RD2) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_RD3__ENET_RGMII_RD3) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6PAD(RGMII_RX_CTL__RGMII_RX_CTL) | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+/* Button assignments for J14 */
+static iomux_v3_cfg_t MX6NAME(button_pads)[] = {
+ /* Menu */
+ MX6PAD(NANDF_D1__GPIO_2_1) | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
+ /* Back */
+ MX6PAD(NANDF_D2__GPIO_2_2) | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
+ /* Labelled Search (mapped to Power under Android) */
+ MX6PAD(NANDF_D3__GPIO_2_3) | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
+ /* Home */
+ MX6PAD(NANDF_D4__GPIO_2_4) | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
+ /* Volume Down */
+ MX6PAD(GPIO_19__GPIO_4_5) | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
+ /* Volume Up */
+ MX6PAD(GPIO_18__GPIO_7_13) | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
+};
+
+iomux_v3_cfg_t MX6NAME(usb_pads)[] = {
+ MX6PAD(GPIO_17__GPIO_7_12) | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#ifdef CONFIG_MXC_SPI
+iomux_v3_cfg_t MX6NAME(ecspi1_pads)[] = {
+ /* SS1 */
+ MX6PAD(EIM_D19__GPIO_3_19) | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6PAD(EIM_D17__ECSPI1_MISO) | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6PAD(EIM_D18__ECSPI1_MOSI) | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6PAD(EIM_D16__ECSPI1_SCLK) | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+#endif
--
1.7.9.5
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
