On 22/09/2012 04:39, Troy Kisky wrote:
> The "plugin" command of mkimage can take this
> file as an argument.
>
> Signed-off-by: Troy Kisky <troy.ki...@boundarydevices.com>
> ---
Hi Troy,
I agree with Vikram that a better explanation of what a plugin is can
help to understand without reading deeply into the i.MX6 manual.
So a "plugin" is a chunk of code that can be called directly by the
BootROM of i.MX processors supporting V2 version of the i.MX header.
In my understanding, this is supported by i.MX53, too. After the plugin
run, the control is returned to the BootROM.
Now that we have some basis, why do we need this mechanism to boot this
board ? Is it not possible to make the same initialization directly in
u-boot ?
In principle, this adds stil some code that is not so easy to maintain.
> arch/arm/cpu/armv7/mx6/Makefile | 5 +-
> arch/arm/cpu/armv7/mx6/plugin.S | 164
> ++++++++++++++++++++++++++++++
> arch/arm/include/asm/arch-mx6/imx-regs.h | 1 +
> 3 files changed, 169 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/cpu/armv7/mx6/plugin.S
>
> diff --git a/arch/arm/cpu/armv7/mx6/Makefile b/arch/arm/cpu/armv7/mx6/Makefile
> index cbce411..b1fce4e 100644
> --- a/arch/arm/cpu/armv7/mx6/Makefile
> +++ b/arch/arm/cpu/armv7/mx6/Makefile
> @@ -33,11 +33,14 @@ SOBJS = lowlevel_init.o
> SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
>
> -all: $(obj).depend $(LIB)
> +all: $(obj).depend $(LIB) plugin.bin
>
> $(LIB): $(OBJS)
> $(call cmd_link_o_target, $(OBJS))
>
> +plugin.bin: plugin.o
> + $(OBJCOPY) -O binary --gap-fill 0xff $< $@
If we add a plugin mechanism, we can have several plugins (booting
directly from Net, maybe ?). We should then have a general mechanism. A
directory "plugins" here can contain the code, and it is compiled only
if a CONFIG_ is set or better if required from imximage.cfg
> +
> #########################################################################
>
> # defines $(obj).depend target
> diff --git a/arch/arm/cpu/armv7/mx6/plugin.S b/arch/arm/cpu/armv7/mx6/plugin.S
> new file mode 100644
> index 0000000..99c6b20
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/mx6/plugin.S
> @@ -0,0 +1,164 @@
> +/*
> + * Copyright (C) 2012 Boundary Devices Inc.
> + *
> + * Licensed under the GPL-2 or later.
> + */
> +#include <config.h>
> +#include <asm/arch/imx-regs.h>
> +
> +#define HAB_RVT_ENTRY 0x98
> +#define HAB_RVT_FAIL_SAFE_VECT 0xbc
> +#define HAB_RVT_LOAD_DATA 0xc8
> +
> +#define HDR_SELF_PTR 0x14
> +#define HDR_BOOT_DATA 0x20
> +#define HDR_IMAGE_LEN 0x24
> +
> +#define L2X0_CTRL 0x100
> +#define SCU_CONFIG 0x004
> +
> +/*
> + * Disable L2 cache because ROM will turn it on when a plugin is used.
> + * There are cache coherence problems if cache is on when Linux kernel
> + * expects it to be off.
> + */
> +.macro disable_l2_cache
> + ldr r1, =L2_BASE_ADDR
> + mov r0, #0x0
> + str r0, [r1, #L2X0_CTRL]
> +.endm
> +
> +
> +/*
> + * plugin_start(void **start, size_t *bytes, UINT32 *ivt_offset)
> + */
> +plugin_start:
> +/* Save the return address and the function arguments */
> + push {r0-r8, lr}
> +
> +/* r0-r2 must be >= 0x100 and must be 4 byte aligned */
> + cmp r0, #0x100
> + cmphs r1, #0x100
> + cmphs r2, #0x100
> +
> +/* rCPU: 22 - mx6q, 12 - mx6dl, 12|0x100 - solo, 2 - sololite */
> +#define rCPU r2
> +#define rIomux r3
> +#define rVal0 r4 /* mx6q value */
> +#define rVal1 r5 /* mx6dl value */
> +#define rVal2 r6 /* mx6solo value */
> +#define rVal3 r7 /* mx6sololite value */
> +#define rFlag lr
> +#define rTable r8
> +
> + orr rFlag, r0, r1
> + orr rFlag, rFlag, r2
> + orrlo rFlag, rFlag, #1
> +
> + mov rCPU, #22 /* mx6q */
> + mov r1, #SCU_BASE_ADDR
> + ldr r0, [r1, #SCU_CONFIG]
> + and r0, r0, #3
> + cmp r0, #3 /* is mx6q? */
> + movne rCPU, #12 /* mx6dl */
> + cmpne r0, #1 /* is mx6dl? */
> + movne rCPU, #2 /* mx6 sololite */
> +
> + ldrne r1, =ANATOP_BASE_ADDR
> + ldrne r0, [r1, #0x280]
> + movne r0, r0, LSR #16
> + cmpne r0, #0x60 /* is mx6 Sololite? */
> + movne rCPU, #12 | 0x100 /* Solo */
Ok - until here you have checked which processor is running. Now the
more obscure code:
> +
> + mov rVal0, #0
> + mov rVal1, #0
> + mov rVal2, #0
> + mov rVal3, #0
> + ldr rIomux, =IOMUXC_BASE_ADDR
> + adr rTable, mx6_table
> + b 3f
> +
> +1: movs r0, r1, LSR #30
> + beq 2f
> + mov r1, r1, LSL rCPU
> + movs r1, r1, LSR #32-10
> + addne r1, rIomux, r1, LSL #2
> + cmp r0, #3
> + subne r0, r0, #1
> + orr r1, r1, r0
> +
The reason is to write GPR12 ? But why do we need a plugin for that ? I
do not understand why we cannot do it in the initialization code of the
SOC, as we usually do.
> +2: ands r0, r1, #3
> + bic r1, r1, #3
> + ldrne rVal0, [rTable], #4
> + movne rVal1, rVal0
> + movne rVal2, rVal0
> + movne rVal3, rVal0
> + subnes r0, r0, #1
> + ldrne rVal1, [rTable], #4
> + movne rVal2, rVal1
> + movne rVal3, rVal1
> + subnes r0, r0, #1
> + ldrne rVal2, [rTable], #4
> + ldrne rVal3, [rTable], #4
> +
> + mov r0, rVal0
> + cmp rCPU, #22
> + movne r0, rVal1
> + cmpne rCPU, #12
> + movne r0, rVal2
> + cmpne rCPU, #12|0x100
> + movne r0, rVal3
> + cmp r1, #0
> + strne r0, [r1]
> +3: ldr r1, [rTable], #4
> + cmp r1, #0
> + bne 1b
> +
> + tst rFlag, #3
> + bne 4f /* Branch if not called as plugin */
> +/* Align end of table to 64 byte boundary */
> + sub rTable, rTable, #1
> + orr rTable, rTable, #0x3f
> + add rTable, rTable, #1
> + ldr r2, [rTable, #HDR_SELF_PTR]
> + ldr r0, [rTable, #HDR_BOOT_DATA]
> + ldr r1, [rTable, #HDR_IMAGE_LEN]
> + sub rTable, r2, r0
> + mov r2, r0
> + mov r3, r1
> + mov r4, #0
> + push {r0-r4}
> + mov r0, #HAB_RVT_LOAD_DATA
> + ldr r4, [r0]
> + mov r0, sp
> + add r1, sp, #4
> + add r2, sp, #8
> + blx r4
Sorry, I need help to understand this code
> +
> + disable_l2_cache
> + pop {r4, r5}
> + add sp, sp, #12
> + pop {r0-r3}
> +/*
> + * Before returning to ROM, we need to fill the return values arguments
> + * to our function.
> + * plugin_start(void **start, size_t *bytes, UINT32 *ivt_offset)
As the i.MX and the API suggest, it should be possible to write C code
for a plugin. Or am I wrong ?
> diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h
> b/arch/arm/include/asm/arch-mx6/imx-regs.h
> index 8834c59..5c133b2 100644
> --- a/arch/arm/include/asm/arch-mx6/imx-regs.h
> +++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
> @@ -48,6 +48,7 @@
> #define GLOBAL_TIMER_BASE_ADDR 0x00A00200
> #define PRIVATE_TIMERS_WD_BASE_ADDR 0x00A00600
> #define IC_DISTRIBUTOR_BASE_ADDR 0x00A01000
> +#define L2_BASE_ADDR 0x00A02000
> #define GPV0_BASE_ADDR 0x00B00000
> #define GPV1_BASE_ADDR 0x00C00000
> #define PCIE_ARB_BASE_ADDR 0x01000000
>
This is useful in any case. I suggest you put this define in a separate
patch, that can flow independently into mainline.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
