Add Ethernet support.
Signed-off-by: Fabio Estevam <fabio.este...@freescale.com>
---
Hi,
As far as I can see mx6qarm2 and mx6qsabresd has the same circuitry related to
AR8031 Ethernet PHY.
However, with this patch I still get 25MHz instead of 125MHz in the AR8031 CLKO
pin and Ethernet is not functional.
Any ideas are appreciated.
Thanks!
board/freescale/mx6qsabresd/mx6qsabresd.c | 84 +++++++++++++++++++++++++++++
include/configs/mx6qsabresd.h | 13 ++++-
2 files changed, 95 insertions(+), 2 deletions(-)
diff --git a/board/freescale/mx6qsabresd/mx6qsabresd.c
b/board/freescale/mx6qsabresd/mx6qsabresd.c
index c86b51b..4f47fd3 100644
--- a/board/freescale/mx6qsabresd/mx6qsabresd.c
+++ b/board/freescale/mx6qsabresd/mx6qsabresd.c
@@ -56,6 +56,24 @@ iomux_v3_cfg_t uart1_pads[] = {
MX6Q_PAD_CSI0_DAT11__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
};
+iomux_v3_cfg_t enet_pads[] = {
+ MX6Q_PAD_KEY_COL1__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_KEY_COL2__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
iomux_v3_cfg_t usdhc3_pads[] = {
MX6Q_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6Q_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -71,6 +89,11 @@ static void setup_iomux_uart(void)
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
+static void setup_iomux_enet(void)
+{
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+}
+
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg usdhc_cfg[1] = {
{USDHC3_BASE_ADDR},
@@ -95,9 +118,70 @@ u32 get_board_rev(void)
return 0x63000;
}
+
+#define MII_MMD_ACCESS_CTRL_REG 0xd
+#define MII_MMD_ACCESS_ADDR_DATA_REG 0xe
+#define MII_DBG_PORT_REG 0x1d
+#define MII_DBG_PORT2_REG 0x1e
+
+int fecmxc_mii_postcall(int phy)
+{
+ unsigned short val;
+
+ /*
+ * Due to the i.MX6Q SabreSD board HW design,there is
+ * no 125Mhz clock input from SOC. In order to use RGMII,
+ * We need enable AR8031 ouput a 125MHz clk from CLK_25M
+ */
+ miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x7);
+ miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, 0x8016);
+ miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x4007);
+ miiphy_read("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, &val);
+ val &= 0xffe3;
+ val |= 0x18;
+ miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, val);
+
+ /* For the RGMII phy, we need enable tx clock delay */
+ miiphy_write("FEC", phy, MII_DBG_PORT_REG, 0x5);
+ miiphy_read("FEC", phy, MII_DBG_PORT2_REG, &val);
+ val |= 0x0100;
+ miiphy_write("FEC", phy, MII_DBG_PORT2_REG, val);
+
+ miiphy_write("FEC", phy, MII_BMCR, 0xa100);
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ struct eth_device *dev;
+ int ret;
+
+ ret = cpu_eth_init(bis);
+ if (ret) {
+ printf("FEC MXC: %s:failed\n", __func__);
+ return ret;
+ }
+
+ dev = eth_get_dev_by_name("FEC");
+ if (!dev) {
+ printf("FEC MXC: Unable to get FEC device entry\n");
+ return -EINVAL;
+ }
+
+ ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+ if (ret) {
+ printf("FEC MXC: Unable to register FEC mii postcall\n");
+ return ret;
+ }
+
+ return 0;
+}
+
int board_early_init_f(void)
{
setup_iomux_uart();
+ setup_iomux_enet();
return 0;
}
diff --git a/include/configs/mx6qsabresd.h b/include/configs/mx6qsabresd.h
index 448ce28..0f8bcf6 100644
--- a/include/configs/mx6qsabresd.h
+++ b/include/configs/mx6qsabresd.h
@@ -33,9 +33,8 @@
#define CONFIG_REVISION_TAG
/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN CONFIG_ENV_SIZE
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
-#define CONFIG_ARCH_CPU_INIT
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_MXC_GPIO
@@ -55,6 +54,16 @@
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_FEC_MXC_PHYADDR 1
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
--
1.7.9.5
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
