Hi Michal,
On Tue, Aug 14, 2012 at 6:42 AM, Michal Simek <mon...@monstr.eu> wrote:
> The driver is used on Xilinx Zynq platform.
>
> Signed-off-by: Michal Simek <mon...@monstr.eu>
> ---
> drivers/serial/Makefile | 1 +
> drivers/serial/serial_xpssuart.c | 218
> ++++++++++++++++++++++++++++++++++++++
> 2 files changed, 219 insertions(+), 0 deletions(-)
> create mode 100644 drivers/serial/serial_xpssuart.c
I think this would be clearer if it was named serial_zynq.c
> diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
> index 65d0f23..81350d0 100644
> --- a/drivers/serial/Makefile
> +++ b/drivers/serial/Makefile
> @@ -56,6 +56,7 @@ COBJS-$(CONFIG_S3C44B0_SERIAL) += serial_s3c44b0.o
> COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
> COBJS-$(CONFIG_SANDBOX_SERIAL) += sandbox.o
> COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
> +COBJS-$(CONFIG_XPSS_SERIAL) += serial_xpssuart.o
Replace every reference to "XPSS" with "ZYNQ".
> ifndef CONFIG_SPL_BUILD
> COBJS-$(CONFIG_USB_TTY) += usbtty.o
> diff --git a/drivers/serial/serial_xpssuart.c
> b/drivers/serial/serial_xpssuart.c
> new file mode 100644
> index 0000000..3c6d838
> --- /dev/null
> +++ b/drivers/serial/serial_xpssuart.c
> @@ -0,0 +1,218 @@
> +/*
> + * U-Boot driver for Xilinx Dragonfire UART.
Use the released name "Zynq" not the old codename "Dragonfire".
> + *
> + * Copyright (C) 2012 Michal Simek <mon...@monstr.eu>
> + * Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved.
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <watchdog.h>
> +#include <asm/io.h>
> +#include <serial.h>
> +
> +#define XDFUART_SR_TXFULL 0x00000010 /* TX FIFO full */
> +#define XDFUART_SR_RXEMPTY 0x00000002 /* RX FIFO empty */
Replace all references to "XDFUART" with "ZYNQ_UART".
> +
> +#define XDFUART_CR_TX_EN 0x00000010 /* TX enabled */
> +#define XDFUART_CR_RX_EN 0x00000004 /* RX enabled */
> +#define XDFUART_CR_TXRST 0x00000002 /* TX logic reset */
> +#define XDFUART_CR_RXRST 0x00000001 /* RX logic reset */
> +
> +#define XDFUART_MR_PARITY_NONE 0x00000020 /* No parity mode */
> +
> +/* Some clock/baud constants */
> +#define XDFUART_BDIV 15 /* Default/reset BDIV value */
> +#define XDFUART_BASECLK 3125000L /* master / (bdiv + 1) */
> +
> +struct xdfuart {
> + u32 control; /* Control Register [8:0] */
> + u32 mode; /* Mode Register [10:0] */
> + u32 reserved1[4];
> + u32 baud_rate_gen; /* Baud Rate Generator [15:0] */
> + u32 reserved2[4];
> + u32 channel_sts; /* Channel Status [11:0] */
> + u32 tx_rx_fifo; /* FIFO [15:0] or [7:0] */
> + u32 baud_rate_divider; /* Baud Rate Divider [7:0] */
> +};
> +
> +static struct xdfuart *xdf_ports[4] = {
> +#ifdef CONFIG_XPSS_SERIAL_BASEADDR0
> + [0] = (struct xdfuart *)CONFIG_XPSS_SERIAL_BASEADDR0,
> +#endif
> +#ifdef CONFIG_XPSS_SERIAL_BASEADDR1
> + [1] = (struct xdfuart *)CONFIG_XPSS_SERIAL_BASEADDR1,
> +#endif
There are 2 UARTS in hard silicon. They should be supported with
their known base addresses (0xE0000000 and 0xE0001000) here without
pushing that into the config header.
> +#ifdef CONFIG_XPSS_SERIAL_BASEADDR2
> + [2] = (struct xdfuart *)CONFIG_XPSS_SERIAL_BASEADDR2,
> +#endif
> +#ifdef CONFIG_XPSS_SERIAL_BASEADDR3
> + [3] = (struct xdfuart *)CONFIG_XPSS_SERIAL_BASEADDR3,
> +#endif
> +};
> +
> +struct xdfuart_params {
> + u32 baudrate;
> + u32 clock;
> +};
> +
> +static struct xdfuart_params xdf_ports_param[4] = {
> +#if defined(CONFIG_XPSS_SERIAL_BAUDRATE0) &&
> defined(CONFIG_XPSS_SERIAL_CLOCK0)
> + [0].baudrate = CONFIG_XPSS_SERIAL_BAUDRATE0,
> + [0].clock = CONFIG_XPSS_SERIAL_CLOCK0,
> +#endif
> +#if defined(CONFIG_XPSS_SERIAL_BAUDRATE1) &&
> defined(CONFIG_XPSS_SERIAL_CLOCK1)
> + [1].baudrate = CONFIG_XPSS_SERIAL_BAUDRATE1,
> + [1].clock = CONFIG_XPSS_SERIAL_CLOCK1,
> +#endif
> +#if defined(CONFIG_XPSS_SERIAL_BAUDRATE2) &&
> defined(CONFIG_XPSS_SERIAL_CLOCK2)
> + [2].baudrate = CONFIG_XPSS_SERIAL_BAUDRATE2,
> + [2].clock = CONFIG_XPSS_SERIAL_CLOCK2,
> +#endif
> +#if defined(CONFIG_XPSS_SERIAL_BAUDRATE3) &&
> defined(CONFIG_XPSS_SERIAL_CLOCK3)
> + [3].baudrate = CONFIG_XPSS_SERIAL_BAUDRATE3,
> + [3].clock = CONFIG_XPSS_SERIAL_CLOCK3,
> +#endif
> +};
> +
> +/* Set up the baud rate in gd struct */
> +static void xdfuart_serial_setbrg(const int port)
> +{
> + /* Calculation results. */
> + unsigned int calc_bauderror, bdiv, bgen;
> + unsigned long calc_baud = 0;
> + unsigned long baud = xdf_ports_param[port].baudrate;
> + unsigned long clock = xdf_ports_param[port].clock;
> + struct xdfuart *regs = xdf_ports[port];
> +
> + /* master clock
> + * Baud rate = ------------------
> + * bgen * (bdiv + 1)
> + *
> + * Find acceptable values for baud generation.
> + */
> + for (bdiv = 4; bdiv < 255; bdiv++) {
> + bgen = clock / (baud * (bdiv + 1));
> + if (bgen < 2 || bgen > 65535)
> + continue;
> +
> + calc_baud = clock / (bgen * (bdiv + 1));
> +
> + /*
> + * Use first calculated baudrate with
> + * an acceptable (<3%) error
> + */
> + if (baud > calc_baud)
> + calc_bauderror = baud - calc_baud;
> + else
> + calc_bauderror = calc_baud - baud;
> + if (((calc_bauderror * 100) / baud) < 3)
> + break;
> + }
> +
> + writel(bdiv, ®s->baud_rate_divider);
> + writel(bgen, ®s->baud_rate_gen);
> +}
> +
> +/* Initialize the UART, with...some settings. */
> +static int xdfuart_serial_init(const int port)
> +{
> + struct xdfuart *regs = xdf_ports[port];
> +
> + if (!regs)
> + return -1;
> +
> + /* RX/TX enabled & reset */
> + writel(XDFUART_CR_TX_EN | XDFUART_CR_RX_EN | XDFUART_CR_TXRST | \
> + XDFUART_CR_RXRST, ®s->control);
> + writel(XDFUART_MR_PARITY_NONE, ®s->mode); /* 8 bit, no parity */
> + xdfuart_serial_setbrg(port);
> +
> + return 0;
> +}
> +
> +static void xdfuart_serial_putc(const char c, const int port)
> +{
> + struct xdfuart *regs = xdf_ports[port];
> +
> + while ((readl(®s->channel_sts) & XDFUART_SR_TXFULL) != 0)
> + WATCHDOG_RESET();
> +
> + if (c == '\n') {
> + writel('\r', ®s->tx_rx_fifo);
> + while ((readl(®s->channel_sts) & XDFUART_SR_TXFULL) != 0)
> + WATCHDOG_RESET();
> + }
> + writel(c, ®s->tx_rx_fifo);
> +}
> +
> +static void xdfuart_serial_puts(const char *s, const int port)
> +{
> + while (*s)
> + xdfuart_serial_putc(*s++, port);
> +}
> +
> +static int xdfuart_serial_tstc(const int port)
> +{
> + struct xdfuart *regs = xdf_ports[port];
> +
> + return (readl(®s->channel_sts) & XDFUART_SR_RXEMPTY) == 0;
> +}
> +
> +static int xdfuart_serial_getc(const int port)
> +{
> + struct xdfuart *regs = xdf_ports[port];
> +
> + while (!xdfuart_serial_tstc(port))
> + WATCHDOG_RESET();
> + return readl(®s->tx_rx_fifo);
> +}
> +
> +#if !defined(CONFIG_SERIAL_MULTI)
> +int serial_init(void)
> +{
> + return xdfuart_serial_init(0);
If there is no SERIAL_MULTI support, there should be a config to
select which one to use.
> +}
> +
> +void serial_setbrg(void)
> +{
> + xdfuart_serial_setbrg(0);
> +}
> +
> +void serial_putc(const char c)
> +{
> + xdfuart_serial_putc(c, 0);
> +}
> +
> +void serial_puts(const char *s)
> +{
> + xdfuart_serial_puts(s, 0);
> +}
> +
> +int serial_getc(void)
> +{
> + return xdfuart_serial_getc(0);
> +}
> +
> +int serial_tstc(void)
> +{
> + return xdfuart_serial_tstc(0);
> +}
> +#endif
> --
> 1.7.0.4
>
> _______________________________________________
> U-Boot mailing list
> U-Boot@lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
