> -----Original Message----- > From: Holger Brunck [mailto:holger.bru...@keymile.com] > Sent: 05 July 2012 11:24 > To: Prafulla Wadaskar > Cc: Wolfgang Denk; u-boot@lists.denx.de; Valentin Longchamp > Subject: Re: [U-Boot] [PATCH v2 03/14] arm/km: convert mgcoge3un > target to km_kirkwood > > On 07/04/2012 11:21 AM, Prafulla Wadaskar wrote: > > > > > >> -----Original Message----- > >> From: Wolfgang Denk [mailto:w...@denx.de] > >> Sent: 03 July 2012 23:31 > >> To: Prafulla Wadaskar > >> Cc: Holger Brunck; u-boot@lists.denx.de; Valentin Longchamp > >> Subject: Re: [U-Boot] [PATCH v2 03/14] arm/km: convert mgcoge3un > >> target to km_kirkwood > >> > >> Dear Prafulla, > >> > >> In message <F766E4F80769BD478052FB6533FA745D1A2FE3028D@SC- > >> VEXCH4.marvell.com> you wrote: > >>> > >>> Do you think I should pull this patch series, I hope it applies > >> cleanly on the recent master branch. > >>> Please confirm. > >> > >> I have to admit that I neither reviewed the patches in question, > nor > >> did I follow the whole thread of communication in this patch > series. > >> But the general rule is that if there are no strong argumentents > >> against a patch (like a clear NAK or a specific request for > changes) > >> we will apply it. > > > > Hi Wolfgang, > > This patch series was too old, I was trying to save my effors ;-D > > Finally I pulled these patches and tried to apply, but as I doubted > it failed :-( > > > > Hi Hogler > > > > I could not apply the said patch series to the latest u-boot- > marvell.git master branch > > > > Pls re-submit it. > > > > git-am U-Boot-1-9-arm-km-add-board-type-to-boards.cfg.patch > > > > Applying arm/km: add board type to boards.cfg > > > > error: patch failed: boards.cfg:138 > > error: boards.cfg: patch does not apply > > error: patch failed: include/configs/km_kirkwood.h:42 > > error: include/configs/km_kirkwood.h: patch does not apply > > Patch failed at 0001. > > When you have resolved this problem run "git-am --resolved". > > If you would prefer to skip this patch, instead run "git-am --skip" > > > > sorry but now I am completely confused. Here you say you want to apply > 01-09 > which includes > [PATCH v2 05/14] arm/km: correct init of 88e6352 switch in the > reset_phy function > and > [PATCH v2 09/14] arm/km: add support for external switch configuration > > this includes basic infrastructure for the managed switch. > > In another thread you NAK the whole driver: > http://lists.denx.de/pipermail/u-boot/2012-July/127529.html > > In a further different thread where I asked if I should provide > updates which > apply cleanly you say no there are general updates needed: > http://lists.denx.de/pipermail/u-boot/2012-July/127531.html > > For me these statements are conflicting. > > So can you please state clearly which updates you request from myside > for which > patch and which are from your point of view not acceptable and why? > Thanks
Dear Holger To avoid any further confusion let's keep aside all the past. 1. Pls post the new patch series that is just targeted for bugfixes and updates (no addition of new boards or drivers) 2. You may post anther patch series for addition of new boards which does not have any dependencies (if you have such) 3. You may post a standalone patch for a switch driver, needed ack from Joe, that might go to u-boot-net.git 4. You may post a board support patch using this switch. #1,#2 I hope will be pulled faster, rest may take some time. Regards... Prafulla . . . . _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
