Signed-off-by: Eric Nelson <eric.nel...@boundarydevices.com> --- V2 has been stripped of the board-independent changes and uses clrsetbits_le32() instead of twiddling bits by hand.
V3 returns immediately from setup_sata() if enable_sata_clock() returns an error. board/freescale/mx6qsabrelite/mx6qsabrelite.c | 32 +++++++++++++++++++++++++ include/configs/mx6qsabrelite.h | 13 ++++++++++ 2 files changed, 45 insertions(+), 0 deletions(-) diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c index 1d09a72..c9a108f 100644 --- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c +++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c @@ -25,6 +25,8 @@ #include <asm/arch/imx-regs.h> #include <asm/arch/mx6x_pins.h> #include <asm/arch/iomux-v3.h> +#include <asm/arch/ccm_regs.h> +#include <asm/arch/clock.h> #include <asm/errno.h> #include <asm/gpio.h> #include <mmc.h> @@ -267,6 +269,32 @@ int board_eth_init(bd_t *bis) return 0; } +#ifdef CONFIG_CMD_SATA + +int setup_sata(void) +{ + struct iomuxc_base_regs *const iomuxc_regs + = (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR; + int rval = enable_sata_clock(); + if (rval) + return rval ; + + clrsetbits_le32(&iomuxc_regs->gpr[13], + IOMUXC_GPR13_SATA_MASK, + IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB + |IOMUXC_GPR13_SATA_PHY_7_SATA2M + |IOMUXC_GPR13_SATA_SPEED_3G + |(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT) + |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED + |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16 + |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB + |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V + |IOMUXC_GPR13_SATA_PHY_1_SLOW); + + return 0 ; +} +#endif + int board_early_init_f(void) { setup_iomux_uart(); @@ -283,6 +311,10 @@ int board_init(void) setup_spi(); #endif +#ifdef CONFIG_CMD_SATA + setup_sata(); +#endif + return 0; } diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h index f52c3c7..1d92dd0 100644 --- a/include/configs/mx6qsabrelite.h +++ b/include/configs/mx6qsabrelite.h @@ -71,6 +71,19 @@ #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION +#define CONFIG_CMD_SATA +/* + * SATA Configs + */ +#ifdef CONFIG_CMD_SATA +#define CONFIG_DWC_AHSATA +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_DWC_AHSATA_PORT_ID 0 +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR +#define CONFIG_LBA48 +#define CONFIG_LIBATA +#endif + #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_MII -- 1.7.9 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot