since commits:
davinci: emac: add support for more than 1 PHYs
062fe7d332c28ede25626f448681e43d76bb312e
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
fb1d6332b5430b90a8fa8ebab709f33a60e9f816
I get following warning on the enbw_cmc board:
Err: serial
Net: 5 ETH PHY detected
miiphy_register: non unique device name 'KSZ8873 @ 0x01'
DaVinci-EMAC
Hit any key to stop autoboot: 0
Also I see some debug printfs:
=> run load
+ emac_close
+ emac_ch_teardown
- emac_ch_teardown
+ emac_ch_teardown
- emac_ch_teardown
- emac_close
+ emac_open
- emac_open
Using DaVinci-EMAC device
reason is 062fe7d332c28ede25626f448681e43d76bb312e new define MAX_PHY.
This is set to 3! I get on this board 5 active phys, so
this leads in wrong memory writes ...
so I changed:
- MAX_PHY from 3 to 7
- print an error message if more then MAX_PHYs are
detected.
- fill the active_phy_addr array in a for loop with
0xff
- changed printf() in debug_emac()
Signed-off-by: Heiko Schocher <h...@denx.de>
Cc: Sandeep Paulraj <s-paul...@ti.com>
Cc: Albert ARIBAUD <albert.u.b...@aribaud.net>
Cc: Wolfgang Denk <w...@denx.de>
Cc: Manjunath Hadli <manjunath.ha...@ti.com>
---
drivers/net/davinci_emac.c | 17 +++++++++++------
1 files changed, 11 insertions(+), 6 deletions(-)
diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c
index fa31159..a31e9f1 100644
--- a/drivers/net/davinci_emac.c
+++ b/drivers/net/davinci_emac.c
@@ -85,7 +85,7 @@ static int emac_rx_queue_active = 0;
/* Receive packet buffers */
static unsigned char emac_rx_buffers[EMAC_MAX_RX_BUFFERS *
(EMAC_MAX_ETHERNET_PKT_SIZE + EMAC_PKT_ALIGN)];
-#define MAX_PHY 3
+#define MAX_PHY 7
/* PHY address for a discovered PHY (0xff - not found) */
static u_int8_t active_phy_addr[MAX_PHY] = { 0xff, 0xff, 0xff };
@@ -160,9 +160,8 @@ static int davinci_eth_phy_detect(void)
int j;
unsigned int count = 0;
- active_phy_addr[0] = 0xff;
- active_phy_addr[1] = 0xff;
- active_phy_addr[2] = 0xff;
+ for (i = 0; i < MAX_PHY; i++)
+ active_phy_addr[i] = 0xff;
udelay(1000);
phy_act_state = readl(&adap_mdio->ALIVE);
@@ -175,7 +174,13 @@ static int davinci_eth_phy_detect(void)
for (i = 0, j = 0; i < 32; i++)
if (phy_act_state & (1 << i)) {
count++;
- active_phy_addr[j++] = i;
+ if (count < MAX_PHY)
+ active_phy_addr[j++] = i;
+ else {
+ printf("%s: to much PHYs detected.\n",
+ __func__);
+ break;
+ }
}
num_phy = count;
@@ -752,7 +757,7 @@ int davinci_emac_initialize(void)
if (!ret)
return(0);
else
- printf(" %d ETH PHY detected\n", ret);
+ debug_emac(" %d ETH PHY detected\n", ret);
/* Get PHY ID and initialize phy_ops for a detected PHY */
for (i = 0; i < num_phy; i++) {
--
1.7.6.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
