Dear Macpaul Lin, In message <1317896723-9284-4-git-send-email-macp...@andestech.com> you wrote: > SoC ag101 is the first chip using NDS32 N1213 cpu core. > Add header file of device offset support for SoC ag101. > Add main function of SoC ag101 based on NDS32 n1213 core. > Add lowlevel_init.S and other periphal related code. > > This version of lowlevel_init.S also replace hardcode value > by MARCO defines from the GPL version andesboot for better > code quality. > > Signed-off-by: Macpaul Lin <macp...@andestech.com> > --- > Changes for v1-v4: > - Code clean up. > Changes for v5-v6: > - Split watchdog.S from lowlevel_init.S. > - Fix hardware reset by using watchdog reset in do_reset() in cpu.c. > - reset_cpu was remove inside do_reset(). > - lowlevel_init.S > - Change hard code value into MARCO definitions. > - ftsmc010 > - Fix FTSMC020_TPR_AT2 from 1 to 3 (0xff3ff) > - ftsdmc021 > - Fix hardcoded address of CR1, CR2, TR1, TR2, BANK0 registers. > - Fix the default configuration value of FTSDMC and FTSMC controller. > - Remove some ftpmu010 and flash probe code to C functions. > Changes for v7: > - clean up. > Changes for v8-v9: > - No change. > Changes for v10: > - asm-offset.c: file added for ag101 use only. > - ag101/Makefile: add gen-asm-offset support to ag101 for lowlevel_init.S. > - Makefile: add gen-asm-offset support for NDS32 based core and SoCs. > - cpu.c: remove unused cpu_init(). > - lowlevel_init.S > - Introduce SoC specific gen-asm-offset.h to lowlevel_init.S > - Replace routings by macros to made code much easier to understand. > - Add debug LED support. > - Add CONFIG_MEM_REMAP for those boards must do memort remapping. > Changes for v11: > - arch/nds32/cpu/n1213/ag101/Makefile > - replace $(AR) $(call cmd_link_o_target,...) > Changes for v12: > - Simplify the commit log about the part of lowlevel_init.S. > Changes for v13: > - arch/nds32/cpu/n1213/ag101/Makefile: remove unused gen-asm-offset. > - Makefile: remove unused gen-asm-offset because merged asm-offsets. > Changes for v14: > - lowlevel_init.S: fix include path of <generated/asm-offsets.h> > Changes for v15: > - fix sleep delay. > > arch/nds32/cpu/n1213/ag101/Makefile | 58 +++++++ > arch/nds32/cpu/n1213/ag101/asm-offsets.c | 43 +++++ > arch/nds32/cpu/n1213/ag101/cpu.c | 200 +++++++++++++++++++++++ > arch/nds32/cpu/n1213/ag101/lowlevel_init.S | 238 > ++++++++++++++++++++++++++++ > arch/nds32/cpu/n1213/ag101/timer.c | 204 ++++++++++++++++++++++++ > arch/nds32/cpu/n1213/ag101/watchdog.S | 48 ++++++ > arch/nds32/include/asm/arch-ag101/ag101.h | 68 ++++++++ > 7 files changed, 859 insertions(+), 0 deletions(-) > create mode 100644 arch/nds32/cpu/n1213/ag101/Makefile > create mode 100644 arch/nds32/cpu/n1213/ag101/asm-offsets.c > create mode 100644 arch/nds32/cpu/n1213/ag101/cpu.c > create mode 100644 arch/nds32/cpu/n1213/ag101/lowlevel_init.S > create mode 100644 arch/nds32/cpu/n1213/ag101/timer.c > create mode 100644 arch/nds32/cpu/n1213/ag101/watchdog.S > create mode 100644 arch/nds32/include/asm/arch-ag101/ag101.h
Checkpatch says: total: 0 errors, 16 warnings, 859 lines checked Please clean up and resubmit. Thanks. Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de You don't have to worry about me. I might have been born yesterday... but I stayed up all night. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
