This commit adds USB support for EfikaMX and EfikaSB.
Signed-off-by: Jana Rapava <ferma...@gmail.com>
Signed-off-by: Marek Vasut <marek.va...@gmail.com>
Cc: Remy Bohmer <li...@bohmer.net>
Cc: Stefano Babic <sba...@denx.de>
---
Changes for v2:
- changed to proper patch
Changes for v3:
- merged other USB patches from u-boot-pxa/efikasb
- offset-based access changed to struct-based access
- use {clrset,clr,set}bits_le32() calls
- CodingStyle and naming cleanup
Changes for v4:
- split into patchset
- CodingStyle and naming cleanup
- remove endless loops
- silence compiler warnings
board/efikamx/Makefile | 3 +
board/efikamx/efikamx-usb.c | 380 +++++++++++++++++++++++++++++++++++++++++++
board/efikamx/efikamx.c | 10 +
include/configs/efikamx.h | 16 ++
include/usb/ehci-fsl.h | 119 +++++++++++++-
5 files changed, 527 insertions(+), 1 deletions(-)
create mode 100644 board/efikamx/efikamx-usb.c
diff --git a/board/efikamx/Makefile b/board/efikamx/Makefile
index ee4a16e..860e4d2 100644
--- a/board/efikamx/Makefile
+++ b/board/efikamx/Makefile
@@ -28,6 +28,9 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
COBJS := efikamx.o
+ifdef CONFIG_CMD_USB
+COBJS += efikamx-usb.o
+endif
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/board/efikamx/efikamx-usb.c b/board/efikamx/efikamx-usb.c
new file mode 100644
index 0000000..559470f
--- /dev/null
+++ b/board/efikamx/efikamx-usb.c
@@ -0,0 +1,380 @@
+#include <common.h>
+#include <usb.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx5x_pins.h>
+#include <asm/arch/iomux.h>
+#include <asm/gpio.h>
+#include <usb/ehci-fsl.h>
+#include <errno.h>
+#include <watchdog.h>
+
+#include "../../drivers/usb/host/ehci.h"
+#include "../../drivers/usb/host/ehci-core.h"
+
+/*
+ * Configure the USB H1 and USB H2 IOMUX
+ */
+#define USB_PAD_CONFIG (PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST | \
+ PAD_CTL_DRV_HIGH | PAD_CTL_100K_PU | \
+ PAD_CTL_HYS_ENABLE | PAD_CTL_PUE_PULL)
+void setup_iomux_usb(void)
+{
+ /*
+ * Configure USBH1 pads
+ */
+ mxc_request_iomux(MX51_PIN_USBH1_STP, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_STP, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_CLK, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_CLK, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_DIR, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DIR, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_NXT, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_NXT, USB_PAD_CONFIG);
+
+ mxc_request_iomux(MX51_PIN_USBH1_DATA0, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DATA0, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_DATA1, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DATA1, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_DATA2, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DATA2, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_DATA3, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DATA3, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_DATA4, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DATA4, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_DATA5, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DATA5, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_DATA6, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DATA6, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_USBH1_DATA7, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_DATA7, USB_PAD_CONFIG);
+
+ /*
+ * Configure USBH1 control pads
+ */
+
+ /* USB PHY reset */
+ mxc_request_iomux(MX51_PIN_EIM_D27, IOMUX_CONFIG_ALT1);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D27, PAD_CTL_PKE_ENABLE |
+ PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH);
+
+ /* USB HUB reset */
+ mxc_request_iomux(MX51_PIN_GPIO1_5, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_GPIO1_5, PAD_CTL_PKE_ENABLE |
+ PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH);
+
+
+#ifdef CONFIG_MACH_EFIKASB
+ /*
+ * Configure USBH2 pads (used on EfikaSB)
+ */
+ /* USBH2_DATA */
+ mxc_request_iomux(MX51_PIN_EIM_D16, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D16, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_EIM_D17, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D17, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_EIM_D18, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D18, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_EIM_D19, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D19, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_EIM_D20, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D20, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_EIM_D21, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D21, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_EIM_D22, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D22, USB_PAD_CONFIG);
+ mxc_request_iomux(MX51_PIN_EIM_D23, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_D23, USB_PAD_CONFIG);
+
+ /* USBH2_CLK */
+ mxc_request_iomux(MX51_PIN_EIM_A24, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A24, USB_PAD_CONFIG);
+ /* USBH2_DIR */
+ mxc_request_iomux(MX51_PIN_EIM_A25, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A25, USB_PAD_CONFIG);
+ /* USBH2_STP */
+ mxc_request_iomux(MX51_PIN_EIM_A26, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A26, USB_PAD_CONFIG);
+ /* USBH2_NXT */
+ mxc_request_iomux(MX51_PIN_EIM_A27, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A27, USB_PAD_CONFIG);
+#endif
+
+ /* WIFI EN (act low) */
+ mxc_request_iomux(MX51_PIN_EIM_A22, IOMUX_CONFIG_GPIO);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A22, 0);
+ /* WIFI RESET */
+ mxc_request_iomux(MX51_PIN_EIM_A16, IOMUX_CONFIG_GPIO);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A16, 0);
+ /* BT EN (act low) */
+ mxc_request_iomux(MX51_PIN_EIM_A17, IOMUX_CONFIG_GPIO);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A17, 0);
+}
+
+/*
+ * Enable devices connected to USB BUSes
+ */
+void efika_usb_enable_devices(void)
+{
+ /* Enable Bluetooth */
+ gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A17), 0);
+ udelay(10000);
+ gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_A17), 1);
+
+ /* Enable WiFi */
+ gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A22), 1);
+ udelay(10000);
+
+ /* Reset the WiFi chip */
+ gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A16), 0);
+ udelay(10000);
+ gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_A16), 1);
+}
+
+/*
+ * Reset USB HUB (or HUBs on EfikaSB)
+ */
+void efika_usb_hub_reset(void)
+{
+ /* HUB reset */
+ gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 1);
+ udelay(1000);
+ gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 0);
+ udelay(1000);
+ gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 1);
+}
+
+/*
+ * Reset USB PHY (or PHYs on EfikaSB)
+ */
+void efika_usb_phy_reset(void)
+{
+ /* SMSC 3317 PHY reset */
+ gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_D27), 0);
+ udelay(1000);
+ gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_D27), 1);
+}
+
+/*
+ * Configure control registers of the USB controller
+ */
+void control_regs_setup(struct usb_control_regs *control)
+{
+ clrsetbits_le32(&control->usbctrl,
+ (MXC_OTG_WUE | MXC_OTG_PM | MX51_H1_ULPI_IE | MX51_H1_WUE),
+ MX51_H1_PM);
+
+ clrsetbits_le32(&control->phyctrl0,
+ MX51_OTG_OVERCURD,
+ MX51_EHCI_POWERPINSE);
+
+ clrsetbits_le32(&control->phyctrl1,
+ MX51_SYSCLOCK_MASK,
+ MX51_SYSCLOCK_24_MHZ);
+
+ setbits_le32(&control->usbctrl1, MX51_H1_EXTCLKE);
+
+ clrsetbits_le32(&control->uh2ctrl,
+ (MX51_H2_ULPI_IE | MX51_H2_WUE),
+ MX51_H2_PM);
+
+ udelay(10000);
+}
+
+#define ULPI_ADDR_SHIFT 16
+#define ulpi_write_mask(value) ((value) & 0xff)
+#define ulpi_read_mask(value) (((value) >> 8) & 0xff)
+
+u32 ulpi_wait(u32 ulpi_bit, const char *operation, struct usb_ehci *ehci)
+{
+ int timeout = ULPI_TIMEOUT;
+ u32 tmp;
+ while (--timeout) {
+ tmp = readl(&ehci->ulpi_viewpoint);
+ if (!(tmp & ulpi_bit))
+ break;
+ WATCHDOG_RESET();
+ }
+ if (!timeout) {
+ printf("ULPI %s timed out\n", operation);
+ return 0;
+ }
+ return tmp;
+}
+
+void ulpi_write(u8 *reg, u32 value, struct usb_ehci *ehci)
+{
+ if (!(readl(&ehci->ulpi_viewpoint) & ULPI_SS)) {
+ writel(ULPI_WU, &ehci->ulpi_viewpoint);
+ ulpi_wait(ULPI_WU, "wakeup", ehci);
+ }
+ writel(ULPI_RWRUN | ULPI_RWCTRL |
+ (u32)reg << ULPI_ADDR_SHIFT | ulpi_write_mask(value),
+ &ehci->ulpi_viewpoint);
+
+ ulpi_wait(ULPI_RWRUN, "write", ehci);
+}
+
+u32 ulpi_read(u8 *reg, struct usb_ehci *ehci)
+{
+ if (!(readl(&ehci->ulpi_viewpoint) & ULPI_SS)) {
+ writel(ULPI_WU, &ehci->ulpi_viewpoint);
+ ulpi_wait(ULPI_WU, "wakeup", ehci);
+ }
+ writel(ULPI_RWRUN | (u32)reg << ULPI_ADDR_SHIFT, &ehci->ulpi_viewpoint);
+ return ulpi_read_mask(ulpi_wait(ULPI_RWRUN, "read", ehci));
+}
+
+void ulpi_init(struct ulpi_regs *ulpi, struct usb_ehci *ehci)
+{
+ u32 tmp = 0;
+ int reg, i;
+
+ /* get ID from ULPI immediate registers */
+ for (reg = ULPI_ID_REGS_COUNT - 1; reg >= 0; reg--)
+ tmp |= ulpi_read((u8 *)reg, ehci) << (reg * 8);
+ /* split into vendor and product ID */
+ debug("Found ULPI TX, ID %04x:%04x\n", tmp >> 16, tmp & 0xffff);
+
+ /* ULPI check integrity */
+ for (i = 0; i < 2; i++) {
+ ulpi_write(&ulpi->scratch_write, ULPI_TEST_VALUE << i, ehci);
+ tmp = ulpi_read(&ulpi->scratch_write, ehci);
+
+ if (tmp != (ULPI_TEST_VALUE << i)) {
+ printf("ULPI integrity check failed\n");
+ return;
+ }
+ }
+
+ /* ULPI set flags */
+ ulpi_write(&ulpi->otg_ctrl_write,
+ ULPI_OTG_EXT_VBUS_IND |
+ ULPI_OTG_DM_PULLDOWN | ULPI_OTG_DP_PULLDOWN, ehci);
+ ulpi_write(&ulpi->function_ctrl_write,
+ ULPI_FC_XCVR_SELECT | ULPI_FC_OPMODE_NORMAL |
+ ULPI_FC_SUSPENDM_PWRED, ehci);
+ ulpi_write(&ulpi->iface_ctrl_write, 0, ehci);
+ ulpi_write(&ulpi->otg_ctrl_set,
+ ULPI_OTG_DRV_VBUS | ULPI_OTG_DRV_VBUS_EXT, ehci);
+
+ /*
+ * NOTE: This violates USB specification, but otherwise, USB on Efika
+ * doesn't charge VBUS and as a result, USB doesn't work.
+ */
+ ulpi_write(&ulpi->otg_ctrl_set, ULPI_OTG_CHRG_VBUS, ehci);
+}
+
+void ehci_fixup(uint32_t *status_reg, uint32_t *reg_ref)
+{
+
+ struct usb_ehci *ehci = (struct usb_ehci *)(OTG_BASE_ADDR +
+ (MX51_REGISTER_LAYOUT_LENGTH));
+ struct ulpi_regs *ulpi = (struct ulpi_regs *)0;
+ u32 tmp = ulpi_read(&ulpi->otg_ctrl_write, ehci);
+ tmp |= (1 << 4);
+ ulpi_write(&ulpi->otg_ctrl_write, tmp, ehci);
+ wait_ms(50);
+ /* terminate the reset */
+ *reg_ref = ehci_readl(status_reg);
+ *reg_ref |= EHCI_PS_PE;
+}
+
+void ehci0_init(struct usb_ehci *ehci)
+{
+ writel(MX51_16BIT_UTMI, &ehci->portsc);
+}
+
+void ehci1_init(struct usb_ehci *ehci, struct ulpi_regs *ulpi)
+{
+ mxc_request_iomux(MX51_PIN_USBH1_STP, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_STP, PAD_CTL_DRV_HIGH |
+ PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST);
+ gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_USBH1_STP), 0);
+ udelay(1000);
+ gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_USBH1_STP), 1);
+ udelay(1000);
+
+ mxc_request_iomux(MX51_PIN_USBH1_STP, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX51_PIN_USBH1_STP, USB_PAD_CONFIG);
+ udelay(10000);
+
+ clrbits_le32(&ehci->usbcmd, MX51_ITC_IMMEDIATE_MASK);
+ udelay(10000);
+
+ writel(MX51_ULPI_MODE_MASK, &ehci->portsc);
+ udelay(10000);
+
+ ulpi_init(ulpi, ehci);
+}
+
+
+void ehci2_init(struct usb_ehci *ehci, struct ulpi_regs *ulpi)
+{
+ mxc_request_iomux(MX51_PIN_EIM_A26, IOMUX_CONFIG_ALT1);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A26, PAD_CTL_DRV_HIGH |
+ PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST);
+ gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A26), 0);
+ udelay(1000);
+ gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_A26), 1);
+ udelay(1000);
+
+ mxc_request_iomux(MX51_PIN_EIM_A26, IOMUX_CONFIG_ALT2);
+ mxc_iomux_set_pad(MX51_PIN_EIM_A26, USB_PAD_CONFIG);
+
+ writel(MX51_ULPI_MODE_MASK, &ehci->portsc);
+ udelay(10000);
+
+ ulpi_init(ulpi, ehci);
+}
+
+int ehci_hcd_init(void)
+{
+ struct usb_ehci *ehci;
+ struct usb_control_regs *mx5_usb_control_regs;
+ struct ulpi_regs *ulpi;
+
+ /* Init iMX51 EHCI */
+ efika_usb_phy_reset();
+ efika_usb_hub_reset();
+ efika_usb_enable_devices();
+
+ mx5_usb_control_regs = (struct usb_control_regs *)(OTG_BASE_ADDR +
+ MX51_CTRL_REGS);
+ control_regs_setup(mx5_usb_control_regs);
+
+ ulpi = (struct ulpi_regs *)0;
+ /* Init EHCI core */
+ ehci = (struct usb_ehci *)(OTG_BASE_ADDR +
+ (MX51_REGISTER_LAYOUT_LENGTH * CONFIG_MXC_USB_PORT));
+ hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+ hcor = (struct ehci_hcor *)((uint32_t) hccr +
+ HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
+ setbits_le32(&ehci->usbmode, CM_HOST);
+ setbits_le32(&ehci->control, USB_EN);
+
+ switch (CONFIG_MXC_USB_PORT) {
+ case 0:
+ ehci0_init(ehci);
+ break;
+ case 1:
+ ehci1_init(ehci, ulpi);
+ break;
+#ifdef MACH_EFIKASB
+ case 2:
+ ehci2_init(ehci, ulpi);
+ break;
+#endif
+ };
+
+ /* EfikaMX USB has issues ... */
+ udelay(10000);
+
+
+ return 0;
+}
+
+int ehci_hcd_stop(void)
+{
+ return 0;
+}
diff --git a/board/efikamx/efikamx.c b/board/efikamx/efikamx.c
index 5be1f6c..51c1854 100644
--- a/board/efikamx/efikamx.c
+++ b/board/efikamx/efikamx.c
@@ -489,6 +489,15 @@ static inline void setup_iomux_ata(void) { }
#endif
/*
+ * EHCI USB
+ */
+#ifdef CONFIG_CMD_USB
+void setup_iomux_usb(void);
+#else
+static inline void setup_iomux_usb(void) { }
+#endif
+
+/*
* LED configuration
*/
void setup_iomux_led(void)
@@ -621,6 +630,7 @@ int board_late_init(void)
setup_iomux_led();
setup_iomux_ata();
+ setup_iomux_usb();
efikamx_toggle_led(EFIKAMX_LED_BLUE);
diff --git a/include/configs/efikamx.h b/include/configs/efikamx.h
index fdd0a14..9632b5d 100644
--- a/include/configs/efikamx.h
+++ b/include/configs/efikamx.h
@@ -40,6 +40,10 @@
#define CONFIG_SYS_TEXT_BASE 0x97800000
+#define CONFIG_L2_OFF
+#define CONFIG_SYS_ICACHE_OFF
+#define CONFIG_SYS_DCACHE_OFF
+
/*
* Bootloader Components Configuration
*/
@@ -168,6 +172,18 @@
#endif
/*
+ * USB
+ */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_MXC_USB_PORT 1
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_KEYBOARD
+#endif /* CONFIG_CMD_USB */
+
+/*
* Filesystems
*/
#ifdef CONFIG_CMD_FAT
diff --git a/include/usb/ehci-fsl.h b/include/usb/ehci-fsl.h
index 67600ed..b107f71 100644
--- a/include/usb/ehci-fsl.h
+++ b/include/usb/ehci-fsl.h
@@ -169,6 +169,79 @@
#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC512x_USB_ADDR
#endif
+#if defined(CONFIG_MX51) || defined(CONFIG_MX31)
+/* USB_CTRL register bits of interest*/
+#define MXC_OTG_SIC_SHIFT 29
+#define MXC_OTG_SIC_MASK (0x3 << MX31_OTG_SIC_SHIFT)
+#define MXC_OTG_WUE (1 << 27)
+#define MXC_OTG_PM (1 << 24)
+#endif
+
+#ifdef CONFIG_MX51
+#define MX51_REGISTER_LAYOUT_LENGTH 0x200
+
+/* Register offsets for MX51 */
+#define MX51_OTG_ID 0x000
+#define MX51_UH1_ID 0x200
+#define MX51_UH2_ID 0x400
+#define MX51_CTRL_REGS 0x800
+
+/* USB_CTRL register bits of interest*/
+#define MX51_OTG_PM (1 << 24)
+#define MX51_H1_ULPI_IE (1 << 12)
+#define MX51_H1_WUE (1 << 11)
+#define MX51_H1_PM (1 << 8)
+
+/* PHY_CTRL_0 register bits of interest */
+#define MX51_OTG_OVERCURD (1 << 8)
+#define MX51_EHCI_POWERPINSE (1 << 5)
+
+/* PHY_CTRL_1 register bits of interest */
+#define MX51_SYSCLOCK_24_MHZ (1 << 0)
+#define MX51_SYSCLOCK_MASK (~(0xffffffff << 2))
+
+/* USB_CTRL_1 register bits of interest */
+#define MX51_H1_EXTCLKE (1 << 25)
+
+/* USB Host 2 CTRL register bits of interest */
+#define MX51_H2_ULPI_IE (1 << 8)
+#define MX51_H2_WUE (1 << 7)
+#define MX51_H2_PM (1 << 4)
+
+/* PORTSCx bits of interest */
+#define MX51_ULPI_MODE_MASK (2 << 30)
+#define MX51_16BIT_UTMI (1 << 28)
+
+/* USBCMD bits of interest */
+#define MX51_ITC_IMMEDIATE_MASK (0xff << 16)
+#endif
+
+/*
+* ULPI
+*/
+#define ULPI_ID_REGS_COUNT 4
+#define ULPI_TEST_VALUE 0x55
+#define ULPI_TIMEOUT 1000 /* some reasonable value */
+
+/* ULPI viewport control bits */
+#define ULPI_WU (1 << 31)
+#define ULPI_SS (1 << 27)
+#define ULPI_RWRUN (1 << 30)
+#define ULPI_RWCTRL (1 << 29)
+
+/* ULPI OTG Control bits of interest */
+#define ULPI_OTG_EXT_VBUS_IND (1 << 7)
+#define ULPI_OTG_DM_PULLDOWN (1 << 2)
+#define ULPI_OTG_DP_PULLDOWN (1 << 1)
+#define ULPI_OTG_DRV_VBUS (1 << 5)
+#define ULPI_OTG_DRV_VBUS_EXT (1 << 6)
+#define ULPI_OTG_CHRG_VBUS (1 << 4)
+
+/* ULPI Function Control bits of interest */
+#define ULPI_FC_XCVR_SELECT (1 << 0)
+#define ULPI_FC_OPMODE_NORMAL (0 << 3)
+#define ULPI_FC_SUSPENDM_PWRED (1 << 6)
+
/*
* USB Registers
*/
@@ -210,7 +283,7 @@ struct usb_ehci {
u32 txfilltuning; /* 0x164 - Host TT Transmit
pre-buffer packet tuning */
u8 res7[0x8];
- u32 ulpi_viewpoint; /* 0x170 - ULPI Reister Access */
+ u32 ulpi_viewpoint; /* 0x170 - ULPI Register Access */
u8 res8[0xc];
u32 config_flag; /* 0x180 - Configured Flag Register */
u32 portsc; /* 0x184 - Port status/control */
@@ -242,4 +315,48 @@ struct usb_ehci {
u8 res13[0xafc];
};
+struct usb_control_regs {
+ u32 usbctrl; /* 0x800 - USB Control */
+ u32 otgmirror; /* 0x804 - OTG Port Mirror */
+ u32 phyctrl0; /* 0x808 - UTMI PHY Control Register 0 */
+ u32 phyctrl1; /* 0x80C - UTMI PHY Control Register 1 */
+ u32 usbctrl1; /* 0x810 - USB Control Register 1 */
+ u32 uh2ctrl; /* 0x814 - USB Host2 Control */
+ u32 uh3ctrl; /* 0x818 - USB Host3 Control */
+};
+
+struct ulpi_regs {
+ u8 vendor_id_low; /* 0x00 - Vendor ID lower byte */
+ u8 vendor_id_high; /* 0x01 - Vendor ID upper byte */
+ u8 product_id_low; /* 0x02 - Product ID lower byte */
+ u8 product_id_high; /* 0x03 - Product ID higher byte */
+ /* Function Control; 0x04 - 0x06 Read, 0x04 Write */
+ u8 function_ctrl_write;
+ u8 function_ctrl_set; /* 0x05 Set */
+ u8 function_ctrl_clear; /* 0x06 Clear */
+ /* Interface Control; 0x07 - 0x09 Read, 0x07 Write */
+ u8 iface_ctrl_write;
+ u8 iface_ctrl_set; /* 0x08 Set */
+ u8 iface_ctrl_clear; /* 0x09 Clear */
+ /* OTG Control; 0x0A - 0x0C Read, 0x0A Write */
+ u8 otg_ctrl_write;
+ u8 otg_ctrl_set; /* 0x0B Set */
+ u8 otg_ctrl_clear; /* 0x0C Clear */
+ /* USB Interrupt Enable Rising; 0x0D - 0x0F Read, 0x0D Write */
+ u8 usb_ie_rising_write;
+ u8 usb_ie_rising_set; /* 0x0E Set */
+ u8 usb_ie_rising_clear; /* 0x0F Clear */
+ /* USB Interrupt Enable Falling; 0x10 - 0x12 Read, 0x10 Write */
+ u8 usb_ie_falling_write;
+ u8 usb_ie_falling_set; /* 0x11 Set */
+ u8 usb_ie_falling_clear; /* 0x12 Clear */
+ u8 usb_int_status; /* 0x13 - USB Interrupt Status */
+ u8 usb_int_latch; /* 0x14 - USB Interrupt Latch */
+ u8 debug; /* 0x15 - Debug */
+ /* Scratch Register; 0x16 - 0x18 Read, 0x16 Write */
+ u8 scratch_write;
+ u8 scratch_set; /* 0x17 Set */
+ u8 scratch_clear; /* 0x18 Clear*/
+};
+
#endif /* _EHCI_FSL_H */
--
1.7.6.3
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
