Dear Mike Frysinger, In message <1310451782-19008-1-git-send-email-vap...@gentoo.org> you wrote: > The following changes since commit 68d4230c3ccce96a72c5b99e48399bf1796fe3c6: > > powerpc/85xx: Add default usb mode and phy type to hwconfig (2011-07-11 > 13:24:21 -0500) > > are available in the git repository at: > git://www.denx.de/git/u-boot-blackfin.git master > > Harald Krapfenbauer (2): > Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings > Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support > > Mike Frysinger (19): > Blackfin: uart: move debug buffers into local bss > Blackfin: uart: add multiple serial support > Blackfin: adi boards: enable multi serial support by default > Blackfin: dont reset SWRST on newer bf526 parts > Blackfin: add init.elf helper code > Blackfin: uart: fix printf warning > Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR > Blackfin: gpio: optimize free path a little > Blackfin: sync MMR read/write helpers with Linux > Blackfin: portmux: allow header to be included in assembly files > Blackfin: drop unused dma.h header from start code > Blackfin: adi boards: enable pretty flash progress output > Blackfin: split out async setup > Blackfin: serial: convert to bfin_{read,write} helpers > Blackfin: update anomaly lists to latest public info > Blackfin: adi boards: also set stderr to nc with helper > Blackfin: serial: move early debug strings into .rodata section > Blackfin: switch to common display_options() > Blackfin: jtag-console: fix timer usage > > Makefile | 3 +- > arch/blackfin/cpu/.gitignore | 3 + > arch/blackfin/cpu/Makefile | 7 +- > arch/blackfin/cpu/cpu.c | 16 +- > arch/blackfin/cpu/gpio.c | 2 + > arch/blackfin/cpu/init.S | 9 + > arch/blackfin/cpu/init.lds.S | 25 +++ > arch/blackfin/cpu/initcode.c | 61 ++----- > arch/blackfin/cpu/initcode.h | 71 +++++++ > arch/blackfin/cpu/jtag-console.c | 4 +- > arch/blackfin/cpu/reset.c | 4 +- > arch/blackfin/cpu/serial.c | 234 > ++++++++++++++++++------ > arch/blackfin/cpu/serial.h | 70 +++++--- > arch/blackfin/cpu/start.S | 1 - > arch/blackfin/include/asm/blackfin_local.h | 88 +++++----- > arch/blackfin/include/asm/config.h | 3 + > arch/blackfin/include/asm/gpio.h | 3 +- > arch/blackfin/include/asm/mach-bf506/anomaly.h | 25 ++- > arch/blackfin/include/asm/mach-bf518/anomaly.h | 28 ++- > arch/blackfin/include/asm/mach-bf527/anomaly.h | 38 +++-- > arch/blackfin/include/asm/mach-bf533/anomaly.h | 23 ++- > arch/blackfin/include/asm/mach-bf537/anomaly.h | 37 +++-- > arch/blackfin/include/asm/mach-bf538/anomaly.h | 42 +++-- > arch/blackfin/include/asm/mach-bf548/anomaly.h | 227 +++++++++++++---------- > arch/blackfin/include/asm/mach-bf561/anomaly.h | 136 ++++++++------ > arch/blackfin/include/asm/portmux.h | 4 + > arch/blackfin/lib/board.c | 6 +- > board/cm-bf537e/cm-bf537e.c | 34 +++-- > board/cm-bf537u/cm-bf537u.c | 39 ++-- > board/tcm-bf537/tcm-bf537.c | 34 +++-- > common/serial.c | 3 + > include/configs/bf537-stamp.h | 1 - > include/configs/bfin_adi_common.h | 12 +- > include/configs/cm-bf537e.h | 20 ++- > include/configs/cm-bf537u.h | 24 ++- > include/configs/tcm-bf537.h | 20 ++- > include/serial.h | 9 + > 37 files changed, 904 insertions(+), 462 deletions(-) > create mode 100644 arch/blackfin/cpu/init.S > create mode 100644 arch/blackfin/cpu/init.lds.S > create mode 100644 arch/blackfin/cpu/initcode.h
Applied, thanks. Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de "An open mind has but one disadvantage: it collects dirt." - a saying at RPI _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot