[U-Boot] [PATCH 3/4] Armada100: Enable 88E3015 PHY support for GplugD

[Ajay Bhargav]

This patch adds support for 88E3015 PHY for Marvell GplugD board.

Signed-off-by: Ajay Bhargav <ajay.bhar...@einfochips.com>
---
 board/Marvell/gplugd/gplugd.c |   35 +++++++++++++++++++++++++++++++++++
 include/configs/gplugd.h      |   14 ++++++++++++++
 2 files changed, 49 insertions(+), 0 deletions(-)

diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c
index dc7d89d..347a689 100644
--- a/board/Marvell/gplugd/gplugd.c
+++ b/board/Marvell/gplugd/gplugd.c
@@ -32,6 +32,8 @@
 #include <mvmfp.h>
 #include <asm/arch/mfp.h>
 #include <asm/arch/armada100.h>
+#include <asm/gpio.h>
+#include <miiphy.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -49,6 +51,7 @@ int board_early_init_f(void)
        };
        /* configure MFP's */
        mfp_config(mfp_cfg);
+
        return 0;
 }
 
@@ -58,5 +61,37 @@ int board_init(void)
        gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD;
        /* adress of boot parameters */
        gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
+       /* Assert PHY_RST# */
+       gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_CLR);
+       udelay(10);
+       /* Deassert PHY_RST# */
+       gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_SET);
        return 0;
 }
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and initialize PHY chip 88E3015 */
+void reset_phy(void)
+{
+       u16 phy_adr;
+       const char *name = "armd-fec0";
+
+       if (miiphy_set_current_dev(name))
+               return;
+
+       /* command to read PHY dev address */
+       if (miiphy_read(name, 0xff, 0xff, (u16 *) &phy_adr)) {
+               printf("Err..%s could not read PHY dev address\n",
+                               __func__);
+               return;
+       }
+
+       /* Set Ethernet LED in TX blink mode */
+       miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00);
+       miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL);
+
+       /* reset the phy */
+       miiphy_reset(name, phy_adr);
+       printf("88E3015 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h
index cc14f49..412c959 100644
--- a/include/configs/gplugd.h
+++ b/include/configs/gplugd.h
@@ -65,6 +65,20 @@
 #undef CONFIG_CMD_NET
 #undef CONFIG_CMD_NFS
 
+/* GPIO Support */
+#define CONFIG_ARMADA100_GPIO
+
+/* PHY configuration */
+#define CONFIG_MII
+#define CONFIG_CMD_MII
+#define CONFIG_RESET_PHY_R
+/* 88E3015 register definition */
+#define PHY_LED_PAR_SEL_REG            22
+#define PHY_LED_MAN_REG                        25
+#define PHY_LED_VAL                    0x5b    /* LINK LED1, ACT LED2 */
+/* GPIO Configuration for PHY */
+#define CONFIG_SYS_GPIO_PHY_RST                104     /* GPIO104 */
+
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
-- 
1.7.0.4

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot