Hi Jonas, I tested your ROCK 5B+ patches and the results are below.
Hardware / build: - Board: Radxa ROCK 5B+ rev 1.2 (32 GB LPDDR5) - Toolchain: aarch64-linux-gnu-gcc 15.1.0 - TPL: rk3588_ddr_lp4_2112MHz_lp5_2400MHz_v1.19.bin - BL31: rk3588_bl31_v1.51.elf - Boot: microSD - U-Boot build: 2026.01-rc1-00252-g0afc36a2f4dc Results: - Detected as “Radxa ROCK 5B+” (rk3588-rock-5b-plus.dtb) - SD and USB enumeration work correctly - Ethernet reports “No ethernet found” (GMAC node not yet enabled) Full boot log attached below. Tested-by: Bryan Hinton <[email protected]> Thanks, Bryan --- Boot log: U-Boot 2026.01-rc1-00252-g0afc36a2f4dc (Nov 04 2025 - 15:52:02 -0600) Model: Radxa ROCK 5B+ SoC: RK3588 DRAM: 32 GiB (total 31.7 GiB) Core: 380 devices, 34 uclasses, devicetree: separate MMC: mmc@fe2c0000: 1, mmc@fe2e0000: 0 Loading Environment from nowhere... OK In: serial@feb50000 Out: serial@feb50000 Err: serial@feb50000 Model: Radxa ROCK 5B+ SoC: RK3588 Net: No ethernet found. Hit any key to stop autoboot: 0 => env print fdtfile fdtfile=rockchip/rk3588-rock-5b-plus.dtb => fdt print / model No FDT memory address configured. Please configure the FDT address via "fdt addr <address>" command. Aborting! => fdt print / compatible No FDT memory address configured. Please configure the FDT address via "fdt addr <address>" command. Aborting! => usb start starting USB... USB EHCI 1.00 USB OHCI 1.0 USB EHCI 1.00 USB OHCI 1.0 Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus usb@fc800000: 1 USB Device(s) found Bus usb@fc840000: 1 USB Device(s) found Bus usb@fc880000: 1 USB Device(s) found Bus usb@fc8c0000: 1 USB Device(s) found Bus usb@fcd00000: 1 USB Device(s) found Bus usb@fc400000: 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found => mmc list mmc@fe2c0000: 1 mmc@fe2e0000: 0 => bdinfo boot_params = 0x0000000000000000 DRAM bank = 0x0000000000000000 -> start = 0x0000000000200000 -> size = 0x00000000efe00000 DRAM bank = 0x0000000000000001 -> start = 0x0000000100000000 -> size = 0x00000002fc000000 DRAM bank = 0x0000000000000002 -> start = 0x00000003fc500000 -> size = 0x0000000003a00000 DRAM bank = 0x0000000000000003 -> start = 0x0000000400000000 -> size = 0x0000000400000000 flashstart = 0x0000000000000000 flashsize = 0x0000000000000000 flashoffset = 0x0000000000000000 baudrate = 1500000 bps relocaddr = 0x00000000eff07000 reloc off = 0x00000000ef507000 Build = 64-bit current eth = unknown eth-1addr = (not set) IP addr = <NULL> fdt_blob = 0x00000000edbe0a00 lmb_dump_all: memory.count = 0x4 memory[0] [0x200000-0xefffffff], 0xefe00000 bytes, flags: none memory[1] [0x100000000-0x3fbffffff], 0x2fc000000 bytes, flags: none memory[2] [0x3fc500000-0x3ffefffff], 0x3a00000 bytes, flags: none memory[3] [0x400000000-0x7ffffffff], 0x400000000 bytes, flags: none reserved.count = 0x5 reserved[0] [0xecbdd000-0xecbdffff], 0x3000 bytes, flags: no-notify, no-overwrite reserved[1] [0xecbe09f0-0xefffffff], 0x341f610 bytes, flags: no-overwrite reserved[2] [0x100000000-0x3fbffffff], 0x2fc000000 bytes, flags: no-overwrite reserved[3] [0x3fc500000-0x3ffefffff], 0x3a00000 bytes, flags: no-overwrite reserved[4] [0x400000000-0x7ffffffff], 0x400000000 bytes, flags: no-overwrite devicetree = separate serial addr = 0x00000000feb50000 width = 0x0000000000000004 shift = 0x0000000000000002 offset = 0x0000000000000000 clock = 0x00000000016e3600 arch_number = 0x0000000000000000 TLB addr = 0x00000000efff0000 irq_sp = 0x00000000edbe09f0 sp start = 0x00000000edbe09f0 Early malloc usage: 2700 / 10000 => fdt addr 0x00000000edbe0a00 Working FDT set to edbe0a00 => fdt print / model model = "Radxa ROCK 5B+"
