On 09/06/25 17:56, Manorit Chawdhry wrote:
> Hi Neha,
>
> On 15:57-20250609, Neha Malcom Francis wrote:
>> Trigger all tests of PBIST and LBIST using appropriate calls to set the
>> core under test (MAIN R5 2_0) to it's required state.
>>
>> Signed-off-by: Neha Malcom Francis <n-fran...@ti.com>
>> ---
>> No change since v3
>>
>> arch/arm/mach-k3/j784s4/j784s4_init.c | 52 +++++++++++++++++++++++++++
>> 1 file changed, 52 insertions(+)
>>
>> diff --git a/arch/arm/mach-k3/j784s4/j784s4_init.c
>> b/arch/arm/mach-k3/j784s4/j784s4_init.c
>> index 787cf6261e4..6e21d057fb8 100644
>> --- a/arch/arm/mach-k3/j784s4/j784s4_init.c
>> +++ b/arch/arm/mach-k3/j784s4/j784s4_init.c
>> @@ -17,6 +17,7 @@
>> #include <dm/pinctrl.h>
>> #include <mmc.h>
>> #include <remoteproc.h>
>> +#include <k3_bist.h>
>>
>> #include "../sysfw-loader.h"
>> #include "../common.h"
>> @@ -122,6 +123,48 @@ static void setup_navss_nb(void)
>> writel(NB_THREADMAP_BIT2, (uintptr_t)NAVSS0_NBSS_NB1_CFG_NB_THREADMAP);
>> }
>>
>> +/* Execute and check results of BIST executed on MCU1_x and MCU4_O */
>> +static void run_bist_j784s4(struct udevice *dev)
>> +{
>> + struct bist_ops *ops;
>> + struct ti_sci_handle *handle;
>> + int ret;
>> +
>> + ops = (struct bist_ops *)device_get_ops(dev);
>> + handle = get_ti_sci_handle();
>> +
>> + /* get status of HW POST PBIST on MCU1_x */
>> + if (ops->run_pbist_post())
>> + panic("HW POST LBIST on MCU1_x failed\n");
>> +
>> + /* trigger PBIST tests on MCU4_0 */
>> + ret = prepare_pbist(handle);
>> + ret |= ops->run_pbist_neg();
>> + ret |= deprepare_pbist(handle);
>> +
>> + ret |= prepare_pbist(handle);
>> + ret |= ops->run_pbist();
>> + ret |= deprepare_pbist(handle);
>> +
>> + ret |= prepare_pbist(handle);
>> + ret |= ops->run_pbist_rom();
>> + ret |= deprepare_pbist(handle);
>> +
>> + if (ret)
>> + panic("PBIST on MCU4_0 failed: %d\n", ret);
>> +
>> + /* get status of HW POST PBIST on MCU1_x */
>> + if (ops->run_lbist_post())
>> + panic("HW POST LBIST on MCU1_x failed\n");
>> +
>> + /* trigger LBIST tests on MCU1_x */
>> + ret = prepare_lbist(handle);
>> + ret |= ops->run_lbist();
>> + ret |= deprepare_lbist(handle);
>> + if (ret)
>> + panic("LBIST on MCU4_0 failed: %d\n", ret);
>> +}
>> +
>> /*
>> * This uninitialized global variable would normal end up in the .bss
>> section,
>> * but the .bss is cleared between writing and reading this variable, so
>> move
>> @@ -251,6 +294,15 @@ void board_init_f(ulong dummy)
>> printf("AVS init failed: %d\n", ret);
>> }
>>
>> + if (!IS_ENABLED(CONFIG_CPU_V7R) && IS_ENABLED(CONFIG_K3_BIST)) {
>> + ret = uclass_get_device_by_driver(UCLASS_MISC,
>> + DM_DRIVER_GET(k3_bist),
>> + &dev);
>> + if (ret)
>> + panic("Failed to get BIST device: %d\n", ret);
>
> nit: Add "\n" here
Didn't get you, there is already a "\n" here?
>
>> + run_bist_j784s4(dev);
>> + }
>> +
>> if (IS_ENABLED(CONFIG_CPU_V7R))
>> setup_navss_nb();
>>
>> --
>> 2.34.1
>>
>
> Regards,
> Manorit
--
Thanking You
Neha Malcom Francis
