[PATCH v4 2/3] arm: mach-k3: j784s4_init: Trigger LBIST and PBIST on MAIN R5 2_0

[Neha Malcom Francis]

Trigger all tests of PBIST and LBIST using appropriate calls to set the
core under test (MAIN R5 2_0) to it's required state.

Signed-off-by: Neha Malcom Francis <n-fran...@ti.com>
---
No change since v3

 arch/arm/mach-k3/j784s4/j784s4_init.c | 52 +++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)

diff --git a/arch/arm/mach-k3/j784s4/j784s4_init.c 
b/arch/arm/mach-k3/j784s4/j784s4_init.c
index 787cf6261e4..6e21d057fb8 100644
--- a/arch/arm/mach-k3/j784s4/j784s4_init.c
+++ b/arch/arm/mach-k3/j784s4/j784s4_init.c
@@ -17,6 +17,7 @@
 #include <dm/pinctrl.h>
 #include <mmc.h>
 #include <remoteproc.h>
+#include <k3_bist.h>
 
 #include "../sysfw-loader.h"
 #include "../common.h"
@@ -122,6 +123,48 @@ static void setup_navss_nb(void)
        writel(NB_THREADMAP_BIT2, (uintptr_t)NAVSS0_NBSS_NB1_CFG_NB_THREADMAP);
 }
 
+/* Execute and check results of BIST executed on MCU1_x and MCU4_O */
+static void run_bist_j784s4(struct udevice *dev)
+{
+       struct bist_ops *ops;
+       struct ti_sci_handle *handle;
+       int ret;
+
+       ops = (struct bist_ops *)device_get_ops(dev);
+       handle = get_ti_sci_handle();
+
+       /* get status of HW POST PBIST on MCU1_x */
+       if (ops->run_pbist_post())
+               panic("HW POST LBIST on MCU1_x failed\n");
+
+       /* trigger PBIST tests on MCU4_0 */
+       ret = prepare_pbist(handle);
+       ret |= ops->run_pbist_neg();
+       ret |= deprepare_pbist(handle);
+
+       ret |= prepare_pbist(handle);
+       ret |= ops->run_pbist();
+       ret |= deprepare_pbist(handle);
+
+       ret |= prepare_pbist(handle);
+       ret |= ops->run_pbist_rom();
+       ret |= deprepare_pbist(handle);
+
+       if (ret)
+               panic("PBIST on MCU4_0 failed: %d\n", ret);
+
+       /* get status of HW POST PBIST on MCU1_x */
+       if (ops->run_lbist_post())
+               panic("HW POST LBIST on MCU1_x failed\n");
+
+       /* trigger LBIST tests on MCU1_x */
+       ret = prepare_lbist(handle);
+       ret |= ops->run_lbist();
+       ret |= deprepare_lbist(handle);
+       if (ret)
+               panic("LBIST on MCU4_0 failed: %d\n", ret);
+}
+
 /*
  * This uninitialized global variable would normal end up in the .bss section,
  * but the .bss is cleared between writing and reading this variable, so move
@@ -251,6 +294,15 @@ void board_init_f(ulong dummy)
                        printf("AVS init failed: %d\n", ret);
        }
 
+       if (!IS_ENABLED(CONFIG_CPU_V7R) && IS_ENABLED(CONFIG_K3_BIST)) {
+               ret = uclass_get_device_by_driver(UCLASS_MISC,
+                                                 DM_DRIVER_GET(k3_bist),
+                                                 &dev);
+               if (ret)
+                       panic("Failed to get BIST device: %d\n", ret);
+               run_bist_j784s4(dev);
+       }
+
        if (IS_ENABLED(CONFIG_CPU_V7R))
                setup_navss_nb();
 
-- 
2.34.1