On 6/1/25 14:04, Simon Glass wrote:
There are backslashes in some of the tags which seems to be unnecessary.
Remove then.
Change the word 'either' to 'any' since there are three options.
Signed-off-by: Simon Glass <s...@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.g...@gmx.de>
---
doc/usage/cmd/bootefi.rst | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/doc/usage/cmd/bootefi.rst b/doc/usage/cmd/bootefi.rst
index 3efe9e9df57..d6e4e62e383 100644
--- a/doc/usage/cmd/bootefi.rst
+++ b/doc/usage/cmd/bootefi.rst
@@ -20,19 +20,19 @@ Synopsis
Description
-----------
-The *bootefi* command is used to launch a UEFI binary which can be either of
+The *bootefi* command is used to launch a UEFI binary which can be any of
* UEFI application
* UEFI boot services driver
* UEFI run-time services driver
An operating system requires a hardware description which can either be
-presented as ACPI table (CONFIG\_GENERATE\_ACPI\_TABLE=y) or as device-tree.
-The load address of the device-tree may be provided as parameter *fdt\_addr*.
If
+presented as ACPI table (CONFIG_GENERATE_ACPI_TABLE=y) or as device-tree.
+The load address of the device-tree may be provided as parameter *fdt_addr*. If
this address is not specified, the bootefi command will try to fall back in
sequence to:
-* the device-tree specified by environment variable *fdt\_addr*
+* the device-tree specified by environment variable *fdt_addr*
* the device-tree specified by environment variable *fdtcontroladdr*
The load address of the binary is specified by parameter *image_address*. A
@@ -110,7 +110,7 @@ U-Boot can be compiled with UEFI unit tests. These unit
tests are invoked using
the *bootefi selftest* sub-command.
Which unit test is executed is controlled by the environment variable
-*efi\_selftest*. If this variable is not set, all unit tests that are not
marked
+*efi_selftest*. If this variable is not set, all unit tests that are not marked
as 'on request' are executed.
To show a list of the available unit tests the value *list* can be used
@@ -126,7 +126,7 @@ To show a list of the available unit tests the value *list*
can be used
'configuration tables'
...
-A single test is selected for execution by setting the *efi\_selftest*
+A single test is selected for execution by setting the *efi_selftest*
environment variable to match one of the listed identifiers
::
@@ -140,10 +140,10 @@ return to the command line but require a board reset.
Configuration
-------------
-To use the *bootefi* command you must specify CONFIG\_CMD\_BOOTEFI=y.
-The *bootefi bootmgr* sub-command requries CMD\_BOOTEFI\_BOOTMGR=y.
-The *bootefi hello* sub-command requries CMD\_BOOTEFI\_HELLO=y.
-The *bootefi selftest* sub-command depends on CMD\_BOOTEFI\_SELFTEST=y.
+To use the *bootefi* command you must specify CONFIG_CMD_BOOTEFI=y.
+The *bootefi bootmgr* sub-command requries CMD_BOOTEFI_BOOTMGR=y.
+The *bootefi hello* sub-command requries CMD_BOOTEFI_HELLO=y.
+The *bootefi selftest* sub-command depends on CMD_BOOTEFI_SELFTEST=y.
See also
--------
