The flexspi on different SoCs may have different number of LUTs.
So involve lut_num in nxp_fspi_devtype_data to make distinguish.
This patch prepare for the adding of imx8ulp.
Fixes: ef89fd56bdfc ("arm64: dts: imx8ulp: add flexspi node")
Cc: sta...@kernel.org
Signed-off-by: Haibo Chen <haibo.c...@nxp.com>
Reviewed-by: Frank Li <frank...@nxp.com>
Link: https://patch.msgid.link/20240905094338.1986871-3-haibo.c...@nxp.com
Signed-off-by: Mark Brown <broo...@kernel.org>
(Picked from linux 190b7e2efb1ed8435fc7431d9c7a2447d05d5066)
Signed-off-by: Jonathan Currier <dullf...@yahoo.com>
---
drivers/spi/nxp_fspi.c | 42 +++++++++++++++++++++++-------------------
1 file changed, 23 insertions(+), 19 deletions(-)
diff --git a/drivers/spi/nxp_fspi.c b/drivers/spi/nxp_fspi.c
index 7489c896f9d..3d0f659ecb2 100644
--- a/drivers/spi/nxp_fspi.c
+++ b/drivers/spi/nxp_fspi.c
@@ -52,13 +52,6 @@
#include <linux/bug.h>
#include <linux/err.h>
-/*
- * The driver only uses one single LUT entry, that is updated on
- * each call of exec_op(). Index 0 is preset at boot with a basic
- * read operation, so let's use the last entry (31).
- */
-#define SEQID_LUT 31
-
/* Registers used by the driver */
#define FSPI_MCR0 0x00
#define FSPI_MCR0_AHB_TIMEOUT(x) ((x) << 24)
@@ -242,9 +235,6 @@
#define FSPI_TFDR 0x180
#define FSPI_LUT_BASE 0x200
-#define FSPI_LUT_OFFSET (SEQID_LUT * 4 * 4)
-#define FSPI_LUT_REG(idx) \
- (FSPI_LUT_BASE + FSPI_LUT_OFFSET + (idx) * 4)
/* register map end */
@@ -316,6 +306,7 @@ struct nxp_fspi_devtype_data {
unsigned int txfifo;
unsigned int ahb_buf_size;
unsigned int quirks;
+ unsigned int lut_num;
bool little_endian;
};
@@ -324,6 +315,7 @@ static struct nxp_fspi_devtype_data lx2160a_data = {
.txfifo = SZ_1K, /* (128 * 64 bits) */
.ahb_buf_size = SZ_2K, /* (256 * 64 bits) */
.quirks = 0,
+ .lut_num = 32,
.little_endian = true, /* little-endian */
};
@@ -332,6 +324,7 @@ static struct nxp_fspi_devtype_data imx8mm_data = {
.txfifo = SZ_1K, /* (128 * 64 bits) */
.ahb_buf_size = SZ_2K, /* (256 * 64 bits) */
.quirks = 0,
+ .lut_num = 32,
.little_endian = true, /* little-endian */
};
@@ -486,6 +479,8 @@ static void nxp_fspi_prepare_lut(struct nxp_fspi *f,
void __iomem *base = f->iobase;
u32 lutval[4] = {};
int lutidx = 1, i;
+ u32 lut_offset = (f->devtype_data->lut_num - 1) * 4 * 4;
+ u32 target_lut_reg;
/* cmd */
lutval[0] |= LUT_DEF(0, LUT_CMD, LUT_PAD(op->cmd.buswidth),
@@ -530,8 +525,10 @@ static void nxp_fspi_prepare_lut(struct nxp_fspi *f,
fspi_writel(f, FSPI_LCKER_UNLOCK, f->iobase + FSPI_LCKCR);
/* fill LUT */
- for (i = 0; i < ARRAY_SIZE(lutval); i++)
- fspi_writel(f, lutval[i], base + FSPI_LUT_REG(i));
+ for (i = 0; i < ARRAY_SIZE(lutval); i++) {
+ target_lut_reg = FSPI_LUT_BASE + lut_offset + i * 4;
+ fspi_writel(f, lutval[i], base + target_lut_reg);
+ }
dev_dbg(f->dev, "CMD[%x] lutval[0:%x \t 1:%x \t 2:%x \t 3:%x], size:
0x%08x\n",
op->cmd.opcode, lutval[0], lutval[1], lutval[2], lutval[3],
op->data.nbytes);
@@ -731,7 +728,7 @@ static int nxp_fspi_do_op(struct nxp_fspi *f, const struct
spi_mem_op *op)
void __iomem *base = f->iobase;
int seqnum = 0;
int err = 0;
- u32 reg;
+ u32 reg, seqid_lut;
reg = fspi_readl(f, base + FSPI_IPRXFCR);
/* invalid RXFIFO first */
@@ -745,8 +742,9 @@ static int nxp_fspi_do_op(struct nxp_fspi *f, const struct
spi_mem_op *op)
* the LUT at each exec_op() call. And also specify the DATA
* length, since it's has not been specified in the LUT.
*/
+ seqid_lut = f->devtype_data->lut_num - 1;
fspi_writel(f, op->data.nbytes |
- (SEQID_LUT << FSPI_IPCR1_SEQID_SHIFT) |
+ (seqid_lut << FSPI_IPCR1_SEQID_SHIFT) |
(seqnum << FSPI_IPCR1_SEQNUM_SHIFT),
base + FSPI_IPCR1);
@@ -862,7 +860,7 @@ static int nxp_fspi_default_setup(struct nxp_fspi *f)
{
void __iomem *base = f->iobase;
int ret, i;
- u32 reg;
+ u32 reg, seqid_lut;
#if CONFIG_IS_ENABLED(CLK)
/* the default frequency, we will change it later if necessary. */
@@ -933,11 +931,17 @@ static int nxp_fspi_default_setup(struct nxp_fspi *f)
fspi_writel(f, reg, base + FSPI_FLSHB1CR1);
fspi_writel(f, reg, base + FSPI_FLSHB2CR1);
+ /*
+ * The driver only uses one single LUT entry, that is updated on
+ * each call of exec_op(). Index 0 is preset at boot with a basic
+ * read operation, so let's use the last entry.
+ */
+ seqid_lut = f->devtype_data->lut_num - 1;
/* AHB Read - Set lut sequence ID for all CS. */
- fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA1CR2);
- fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA2CR2);
- fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB1CR2);
- fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB2CR2);
+ fspi_writel(f, seqid_lut, base + FSPI_FLSHA1CR2);
+ fspi_writel(f, seqid_lut, base + FSPI_FLSHA2CR2);
+ fspi_writel(f, seqid_lut, base + FSPI_FLSHB1CR2);
+ fspi_writel(f, seqid_lut, base + FSPI_FLSHB2CR2);
return 0;
}
--
2.45.3
