To avoid duplicate maintenance just include jh7110_common.rst to describe
the usage of the different boot sources.
Signed-off-by: Heinrich Schuchardt <heinrich.schucha...@canonical.com>
---
v3:
no change
v2:
new patch
---
doc/board/starfive/milk-v_mars.rst | 12 +--------
doc/board/starfive/pine64_star64.rst | 18 +------------
doc/board/starfive/visionfive2.rst | 39 +---------------------------
3 files changed, 3 insertions(+), 66 deletions(-)
diff --git a/doc/board/starfive/milk-v_mars.rst
b/doc/board/starfive/milk-v_mars.rst
index aba9c9c53d4..ce4539a46f1 100644
--- a/doc/board/starfive/milk-v_mars.rst
+++ b/doc/board/starfive/milk-v_mars.rst
@@ -57,13 +57,6 @@ environment
or the configuration variable CONFIG_DEFAULT_FDT_FILE can be used to set to
provide a default value.
-Boot source selection
----------------------
-
-The board provides the DIP switches MSEL[1:0] to select the boot device out of
-SPI flash, eMMC, SD-card, UART. To select booting from SD-card set the DIP
-switches MSEL[1:0] to 10.
-
Preparing the SD-Card
---------------------
@@ -105,7 +98,4 @@ Copy U-Boot to the SD card
sudo cp jh7110-starfive-visionfive-2.dtb /mnt/
sudo umount /mnt
-Booting
--------
-
-Once you plugin the sdcard and power up, you should see the U-Boot prompt.
+.. include:: jh7110_common.rst
diff --git a/doc/board/starfive/pine64_star64.rst
b/doc/board/starfive/pine64_star64.rst
index 1df4b68e4a0..d1752c452da 100644
--- a/doc/board/starfive/pine64_star64.rst
+++ b/doc/board/starfive/pine64_star64.rst
@@ -55,19 +55,6 @@ environment
or the configuration variable CONFIG_DEFAULT_FDT_FILE can be used to set to
provide a default value.
-Boot source selection
----------------------
-
-Boot mode is selected by an MSEL-DIP marked S1804 and GPIO_0 position adjacent
-to the 40pin GPIO header. ON/ONKE and number markings of the MSEL-DIP are
-misleading; Instead refer to the ``L`` (0) and ``H`` (1) silkscreen for
-accurate selection.
-
-+ (QSPI) Flash: 00
-+ SD: 01
-+ EMMC: 10
-+ UART: 11
-
Preparing the SD-Card
---------------------
@@ -109,10 +96,7 @@ Copy U-Boot to the SD card
sudo cp jh7110-starfive-visionfive-2.dtb /mnt/
sudo umount /mnt
-Booting
--------
-
-Once you plugin the sdcard and power up, you should see the U-Boot prompt.
+.. include:: jh7110_common.rst
Serial Number and MAC address issues
------------------------------------
diff --git a/doc/board/starfive/visionfive2.rst
b/doc/board/starfive/visionfive2.rst
index 44e7fcb3a48..6f3c572f1f8 100644
--- a/doc/board/starfive/visionfive2.rst
+++ b/doc/board/starfive/visionfive2.rst
@@ -132,13 +132,7 @@ Program the SD card
sudo cp jh7110-starfive-visionfive-2.dtb /mnt/
sudo umount /mnt
-Booting
--------
-
-The board provides the DIP switches MSEL[1:0] to select the boot device.
-To select booting from SD-card set the DIP switches MSEL[1:0] to 10.
-
-Once you plugin the sdcard and power up, you should see the U-Boot prompt.
+.. include:: jh7110_common.rst
Sample boot log from StarFive VisionFive2 board
-----------------------------------------------
@@ -479,34 +473,3 @@ Sample boot log from StarFive VisionFive2 board
Welcome to Buildroot
buildroot login:
-
-Booting from SPI
-----------------
-
-Use Building steps from "Booting from MMC using U-Boot SPL" section.
-
-Partition the SPI in Linux via mtdblock. (Require to boot the board in
-SD boot mode by enabling MTD block in Linux)
-
-Use prebuilt image from here [1], which support to partition the SPI flash.
-
-
-Program the SPI (Require to boot the board in SD boot mode)
-
-Execute below steps on U-Boot proper,
-
-.. code-block:: none
-
- sf probe
- fatload mmc 1:3 $kernel_addr_r u-boot.itb
- sf update $kernel_addr_r 0x100000 $filesize
-
- fatload mmc 1:3 $kernel_addr_r u-boot-spl.bin.normal.out
- sf update $kernel_addr_r 0x0 $filesize
-
-
-Power off the board
-
-Change DIP switches MSEL[1:0] are set to 00, select the boot mode to flash
-
-Power up the board.
--
2.48.1
