Hi, Stefano,
On Fri, Apr 22, 2011 at 12:36 PM, Jason Hui <jason....@linaro.org> wrote:
> Hi, Stefano,
>
> On Fri, Apr 22, 2011 at 1:43 AM, Stefano Babic <sba...@denx.de> wrote:
>> On 04/20/2011 12:47 PM, Jason Liu wrote:
>>
>>> +int board_mmc_getcd(u8 *cd, struct mmc *mmc)
>>> +{
>>> + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
>>> +
>>> + if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
>>> + *cd = mxc_gpio_get(77); /*GPIO3_13*/
>>> + else
>>> + *cd = mxc_gpio_get(75); /*GPIO3_11*/
>>> +
>>> + return 0;
>>> +}
>>
>> Rereading the thread regarding this board I see there is an open
>> question issued by Wolfgang about this code, if accessors should be used
>> in this case. IMHO the code is correct, using the GPIO get function to
>> acquire the current value of a pin. Wolfgang, is it enough to answer
>> your question ? Do you see an open issue ?
>>
>>> +/* PMIC Configs */
>>> +#define CONFIG_FSL_PMIC
>>> +#define CONFIG_FSL_PMIC_I2C
>>> +#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 8
>>
>> If I am not confused, this setup is not valid as you already sent a
>> patchset to drop these lines and adding support for the DA9053 pmic.
>>
>> PMIC: Add dialog pmic support
>> MX53: loco: Add power init support
>>
>> As this patchset is based on the LOCO patch (this one), and it does not
>> apply anymore, please drop these lines and rebase your patches to add
>> pmic support on the actual state of the current patch.
>> IMHO it should be better if you resend them as a single patchset, as
>> they are strictly related, merging "Add power init support" inside this
>> patch.
>
> OK, I will resend the patchset as the following layout:
>
> MX5: clock: Add clock config interface
> MX5: factor out boot cause funciton to common code
> PMIC: Add dialog pmic support
> MX53: support for freescale MX53LOCO board (merge "Add power init support")
>
> I will rebase on the u-boot-imx git, do you think is it OK?
I just noticed that MX5: factor out boot cause funciton to common code
has been applied.
So, I will send out the following,
MX5: clock: Add clock config interface
PMIC: Add dialog pmic support
MX53: support for freescale MX53LOCO board (merge "Add power init support")
Any comments?
Jason
>
>>
>>
>>> +#define CONFIG_SYS_MEMTEST_START 0x70000000
>>> +#define CONFIG_SYS_MEMTEST_END 0x70010000
>>
>> There is still an open question about this range. Can you answer to
>> Wolfgang's question ?
>
> In fact, I want to give one simple test range when use mtest, I don't know
> what you are worrying about, please tell it clearly?
>
>>
>> Best regards,
>> Stefano
>>
>> --
>> =====================================================================
>> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
>> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>> Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: off...@denx.de
>> =====================================================================
>>
>
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
