Hi, > Am 18.01.2024 um 09:33 schrieb Ivan T. Ivanov <iiva...@suse.de>: > >> I actually just did that. Installed a fresh Tumbleweed on a microSD card, >> booted it up with a rpi4 and after installing all necessary build tools I >> applied your patches to u-boot 2024.01 sources, and then executed these two >> commands to let it compile a u-boot.bin file which I then put in /boot/efi >> to replace the u-boot.bin which is/was already there. Then I pulled the SD >> card and moved it over to the RaspberryPi5 in trying to get it booted up. >> However, again no HDMI output at all and unfortunately also the serial >> output on the debug probe does not show U-boot popping up at all. >> Interestingly, using the patched u-boot.bin with a RaspberryPi4 still works >> and it boots up perfectly fine, but not with the RaspberryPi5 I have here. >> >> Any idea why this might be the case here while you report that the above >> mentioned procedure works for you? In fact, the RaspberryPi5 I have here is >> a 8GB model and with the rpi-eeprom version from 2024/01/05 [1] in case this >> might be relevant. > > EEPROM version on mine device is older[1], but I suspect that size of > the RAM is what make a difference, mine have only 4GB of RAM.
This can be also of course the reason why it works for you while it doesn’t for me. > I am afraid you will have to connect that UART debug cable and share > what is the memory map on your device :-) No problem. Here is the output of the RPI bootloader boot up until the system stalls: — cut here — RPi: BOOTSYS release VERSION:30cc5f37 DATE: 2024/01/05 TIME: 15:57:40 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1704470260 serial 9127ae99 boardrev d04170 stc 923866 AON_RESET: 00000003 PM_RSTS 00001000 RP1_BOOT chip ID: 0x20001927 PM_RSTS: 0x00001000 part 00000000 reset_info 00000000 PMIC reset-event 00000000 rtc 00000000 alarm 00000000 enabled 0 uSD voltage 3.3V Initialising SDRAM 'Micron' 32Gb x2 total-size: 64 Gbit 4267 DDR 4267 1 0 64 152 RP1_BOOT chip ID: 0x20001927 RP1_BOOT chip ID: 0x20001927 RP1_BOOT: fw size 25968 PCI2 init PCI2 reset PCIe scan 00001de4:00000001 RP1_CHIP_INFO 20001927 RPi: BOOTLOADER release VERSION:30cc5f37 DATE: 2024/01/05 TIME: 15:57:40 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1704470260 serial 9127ae99 boardrev d04170 stc 3892985 AON_RESET: 00000003 PM_RSTS 00001000 M.2 PCIe HAT not detected. usb_pd_init status 3 USB_PD CONFIG 0 41 Boot mode: SD (01) order f4 SD HOST: 200000000 CTL0: 0x00800000 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 SD HOST: 200000000 CTL0: 0x00800f00 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 OCR c0ff8000 [291] CID: 00035344534536344780519441cb0123 CSD: 400e00325b590001dbd37f800a404000 SD: bus-width: 4 spec: 2 SCR: 0x02458443 0x00000000 SD HOST: 200000000 CTL0: 0x00800f04 BUS: 50000000 Hz actual: 50000000 HZ div: 4 (2) status: 0x1fff0000 delay: 2 MBR: 0x00002000, 131072 type: 0x0c MBR: 0x00022000, 1024000 type: 0x82 MBR: 0x0011c000,123572224 type: 0x83 MBR: 0x00000000, 0 type: 0x00 USB-PD: src-cap PDO object1 0x0a0191f4 Current 5000 mA Voltage 5000 mV USB-PD: src-cap PDO object2 0x0002d12c Current 3000 mA Voltage 9000 mV USB-PD: src-cap PDO object3 0x0003c0e1 Current 2250 mA Voltage 12000 mV USB-PD: src-cap PDO object4 0x0004b0b4 Current 1800 mA Voltage 15000 mV Trying partition: 0 type: 16 lba: 8192 'mkfs.fat' ' V ^ ' clusters 32695 (4) rsc 4 fat-sectors 128 root dir cluster 1 sectors 32 entries 512 FAT16 clusters 32695 [sdcard] autoboot.txt not found Select partition rsts 0 C(boot_partition) 0 EEPROM config 0 result 0 Trying partition: 0 type: 16 lba: 8192 'mkfs.fat' ' V ^ ' clusters 32695 (4) rsc 4 fat-sectors 128 root dir cluster 1 sectors 32 entries 512 FAT16 clusters 32695 Read config.txt bytes 3046 hnd 0x123c Read ubootconfig.txt bytes 35 hnd 0x468 [sdcard] extraconfig.txt not found [sdcard] pieeprom.upd not found usb_max_current_enable default 0 max-current 5000 Read bcm2712-rpi-5-b.dtb bytes 79357 hnd 0x139f dt-match: compatible: raspberrypi,5-model-b match: brcm,bcm2712 dt-match: compatible: brcm,bcm2712 match: brcm,bcm2712 NOTICE: BL31: v2.6(release):v2.6-239-g2a9ede0bd NOTICE: BL31: Built : 14:26:57, Jun 22 2023 — cut here — Best Regards, Jens -- Jens Maus, Dresden/Germany http://jens-maus.de/
