Although most IDE controller is designed to be connected to PCI bridge,
there are still some IDE controller support AHB interface for SoC design.
The driver implementation of these IDE-AHB controllers differ from other
IDE-PCI controller, some additional registers and commands access is required
during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" in cmd_ide.c is
required to be defined to support these kinds of SoC controllers. Such as
Faraday's FTIDE020 series and Global Unichip's UINF-0301.
Signed-off-by: Macpaul Lin <macp...@andestech.com>
---
README | 8 ++++++++
common/cmd_ide.c | 37 ++++++++++++++++++++++++++++++++++++-
2 files changed, 44 insertions(+), 1 deletions(-)
diff --git a/README b/README
index 727bf8a..3de0605 100644
--- a/README
+++ b/README
@@ -2673,6 +2673,14 @@ Low Level (hardware related) configuration options:
source code. It is used to make hardware dependant
initializations.
+- CONFIG_IDE_AHB:
+ Most IDE controllers were designed to be connected with PCI
+ interface. Only few of them were designed for AHB interface.
+ When software is doing ATA command and data transfer to
+ IDE devices through IDE-AHB controller, some additional
+ registers accessing to these kind of IDE-AHB controller
+ is requierd.
+
- CONFIG_SYS_IMMR: Physical address of the Internal Memory.
DO NOT CHANGE unless you know exactly what you're
doing! (11-4) [MPC8xx/82xx systems only]
diff --git a/common/cmd_ide.c b/common/cmd_ide.c
index ea0f4a7..edb4fc0 100644
--- a/common/cmd_ide.c
+++ b/common/cmd_ide.c
@@ -518,8 +518,22 @@ __ide_outb(int dev, int port, unsigned char val)
{
debug ("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
dev, port, val,
(ATA_CURR_BASE(dev)+CONFIG_SYS_ATA_PORT_ADDR(port)));
+
+#if defined(CONFIG_IDE_AHB)
+ if (port) {
+ /* write command */
+ extern void ide_write_register(int, unsigned int, unsigned
char);
+
+ ide_write_register(dev, port, val);
+ } else {
+ /* write data */
+ outb(val, (ATA_CURR_BASE(dev)));
+ }
+#else
outb(val, (ATA_CURR_BASE(dev)+CONFIG_SYS_ATA_PORT_ADDR(port)));
+#endif
}
+
void ide_outb (int dev, int port, unsigned char val)
__attribute__((weak, alias("__ide_outb")));
@@ -527,7 +541,15 @@ unsigned char inline
__ide_inb(int dev, int port)
{
uchar val;
+
+#if defined(CONFIG_IDE_AHB)
+ extern unsigned char ide_read_register(int, unsigned int);
+
+ val = ide_read_register(dev, port);
+#else
val = inb((ATA_CURR_BASE(dev)+CONFIG_SYS_ATA_PORT_ADDR(port)));
+#endif
+
debug ("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
dev, port, (ATA_CURR_BASE(dev)+CONFIG_SYS_ATA_PORT_ADDR(port)),
val);
return val;
@@ -696,6 +718,7 @@ void ide_init (void)
ide_dev_desc[i].blksz=0;
ide_dev_desc[i].lba=0;
ide_dev_desc[i].block_read=ide_read;
+ ide_dev_desc[i].block_write = ide_write;
if (!ide_bus_ok[IDE_BUS(i)])
continue;
ide_led (led, 1); /* LED on */
@@ -902,7 +925,13 @@ output_data(int dev, ulong *sect_buf, int words)
static void
output_data(int dev, ulong *sect_buf, int words)
{
- outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words<<1);
+#if defined(CONFIG_IDE_AHB)
+ extern void ide_write_data(int, ulong *, int);
+
+ ide_write_data(dev, sect_buf, words);
+#else
+ outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words << 1);
+#endif
}
#endif /* CONFIG_IDE_SWAP_IO */
@@ -960,7 +989,13 @@ input_data(int dev, ulong *sect_buf, int words)
static void
input_data(int dev, ulong *sect_buf, int words)
{
+#if defined(CONFIG_IDE_AHB)
+ extern void ide_read_data(int, ulong *, int);
+
+ ide_read_data(dev, sect_buf, words);
+#else
insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words << 1);
+#endif
}
#endif /* CONFIG_IDE_SWAP_IO */
--
1.7.3.5
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
