Signed-off-by: Michael Schwingen <mich...@schwingen.org>
---
board/actux4/actux4.c | 12 +++++++-----
board/actux4/config.mk | 6 ++----
include/configs/actux4.h | 22 +++++++++++++++++-----
3 files changed, 26 insertions(+), 14 deletions(-)
diff --git a/board/actux4/actux4.c b/board/actux4/actux4.c
index f373b58..f66acd8 100644
--- a/board/actux4/actux4.c
+++ b/board/actux4/actux4.c
@@ -42,6 +42,12 @@
DECLARE_GLOBAL_DATA_PTR;
+int board_early_init_f (void)
+{
+ *IXP425_EXP_CS1 = 0xbd113c42;
+ return 0;
+}
+
int board_init (void)
{
gd->bd->bi_arch_number = MACH_TYPE_ACTUX4;
@@ -88,8 +94,6 @@ int board_init (void)
GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_EXTBUS_CLK);
GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_PCI_CLK);
- *IXP425_EXP_CS1 = 0xbd113c42;
-
udelay (10000);
GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
udelay (10000);
@@ -109,9 +113,7 @@ int checkboard (void)
int dram_init (void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
+ gd->ram_size = PHYS_SDRAM_1_SIZE;
return (0);
}
diff --git a/board/actux4/config.mk b/board/actux4/config.mk
index 9cb838b..be871c1 100644
--- a/board/actux4/config.mk
+++ b/board/actux4/config.mk
@@ -1,4 +1,2 @@
-CONFIG_SYS_TEXT_BASE = 0x00e00000
-
-# include NPE ethernet driver
-BOARDLIBS = arch/arm/cpu/ixp/npe/libnpe.o
+PLATFORM_RELFLAGS += -ffunction-sections
+PLATFORM_LDFLAGS += --gc-sections
diff --git a/include/configs/actux4.h b/include/configs/actux4.h
index 04145c3..ac7d1ba 100644
--- a/include/configs/actux4.h
+++ b/include/configs/actux4.h
@@ -37,6 +37,7 @@
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F 1
/***************************************************************
* U-boot generic defines start here.
@@ -45,7 +46,6 @@
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
-/* size in bytes reserved for initial data */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
@@ -82,8 +82,9 @@
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ 3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK 66000000
+#define CONFIG_SYS_HZ 1000
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x00010000
@@ -109,7 +110,7 @@
/* SDRAM settings */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
-#define CONFIG_SYS_DRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
/* 32MB SDRAM */
#define CONFIG_SYS_SDR_CONFIG 0x18
@@ -119,6 +120,7 @@
#define CONFIG_SYS_DRAM_SIZE 0x02000000
/* FLASH organization */
+#define CONFIG_SYS_TEXT_BASE 0x50000000
#define CONFIG_SYS_MAX_FLASH_BANKS 2
/* max # of sectors per chip */
#define CONFIG_SYS_MAX_FLASH_SECT 70
@@ -153,6 +155,7 @@
#define CONFIG_PHY_ADDR 0x1C
/* MII PHY management */
#define CONFIG_MII 1
+
/* Number of ethernet rx buffers & descriptors */
#define CONFIG_SYS_RX_ETH_BUFFER 16
@@ -181,19 +184,24 @@
"mtd=IXP4XX-Flash.0:252k(uboot),4k(uboot_env);" \
"IXP4XX-Flash.1:128k(ucode),1280k(linux),-(root)\0" \
"kerneladdr=51020000\0" \
+ "kernelfile=actux4/uImage\0" \
+ "rootfile=actux4/rootfs\0" \
"rootaddr=51160000\0" \
"loadaddr=10000\0" \
"updateboot_ser=mw.b 10000 ff 40000;" \
" loady ${loadaddr};" \
" run eraseboot writeboot\0" \
"updateboot_net=mw.b 10000 ff 40000;" \
- " tftp ${loadaddr} u-boot.bin;" \
+ " tftp ${loadaddr} actux4/u-boot.bin;"
\
" run eraseboot writeboot\0" \
"eraseboot=protect off 50000000 5003efff;" \
" erase 50000000 +${filesize}\0" \
"writeboot=cp.b 10000 50000000 ${filesize}\0" \
"eraseenv=protect off 5003f000 5003ffff;" \
" erase 5003f000 5003ffff\0" \
+ "updateucode=loady;" \
+ " era ${npe_ucode} +${filesize};" \
+ " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \
"updateroot=tftp ${loadaddr} ${rootfile};" \
" era ${rootaddr} +${filesize};" \
" cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \
@@ -212,4 +220,8 @@
" tftpboot ${loadaddr} ${kernelfile};" \
" bootm\0"
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */
--
1.7.2.3
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
