On Mon, Jan 31, 2022 at 2:48 PM Adam Ford <aford...@gmail.com> wrote: > > On Mon, Jan 31, 2022 at 2:45 PM Michael Nazzareno Trimarchi > <mich...@amarulasolutions.com> wrote: > > > > Hi > > > > On Mon, Jan 31, 2022 at 9:34 PM Adam Ford <aford...@gmail.com> wrote: > > > > > > On Mon, Jan 31, 2022 at 2:25 PM Michael Nazzareno Trimarchi > > > <mich...@amarulasolutions.com> wrote: > > > > > > > > HI Adam > > > > > > > > On Mon, Jan 31, 2022 at 9:21 PM Adam Ford <aford...@gmail.com> wrote: > > > > > > > > > > I have a situation where the same Flash.bin file can boot an MMC card, > > > > > but hang when booting over USB. > > > > > > > > > > In both cases, I can see the FIT file is loaded, and the various items > > > > > are identified and placed in their respective folders memory > > > > > locations. The only difference I can see is that when jumping to > > > > > 0x920000 (ATF), the USB booting hangs and ATF doesn't appear to > > > > > execute. Is there some special command that I need to issue to unlock > > > > > this memory to execute from it when booting from USB? I am calling > > > > > enable_tzc380 from SPL, and I read the first 100 bytes and last 100 > > > > > bytes and compared it to my bl31.bin file, and it appears to match, so > > > > > I know I can read from it. > > > > > > > > > > U-Boot SPL 2022.01-00836-g3cc200c91a-dirty (Jan 30 2022 - 07:31:51 > > > > > -0600) > > > > > No pmic > > > > > WDT: Not starting watchdog@30280000 > > > > > Trying to boot from USB SDP > > > > > USB EHCI 1.00 > > > > > SDP: initialize... > > > > > SDP: handle requests... > > > > > Downloading file of size 832080 to 0x40400000... done > > > > > Jumping to header at 0x40400000 > > > > > Header Tag is not an IMX image > > > > > Found header at 0x40417c00 > > > > > firmware: 'uboot' > > > > > External data: dst=40200000, offset=3000, size=9ddd8 > > > > > fdt: 'fdt-1' > > > > > External data: dst=4029de00, offset=aaea0, size=87b0 > > > > > loadables: 'atf' > > > > > External data: dst=920000, offset=a0dd8, size=a0c6 > > > > > image entry point: 0x920000 > > > > > > > > > > > > > Check if the uart used on atf and uboot are mapping correctly (but > > > > this should because you can boot from sdcard) > > > > > > As far as i can tell, I have not done any differently in the serial > > > from the NXP downstream. > > > > > > > ENV_IS_EVERYWHERE in configs file. It's no PMIC a problem when you jump > > > > in atf? > > > > > > I have experimented with and without ENV_IS_EVERYWHERE, but that only > > > seemed to help my imx8m Nano when jumping from ATF -> U-Boot. As for > > > my Mini, the jump from SPL->ATF seems to be the issue. > > > > > > What might the PMIC have to do with the ATF? From what I can tell, > > > the PMIC is pre-configured and the default voltages appear to boot the > > > > I have only seen this. I don't say that is connected. If the voltage > > are ok and you don't need > > to program it I don't see the problem > > > > > MMC. i had to disable the PMIC driver in order to make room for the > > > USB code. I have a few lines of code in my board's spl.c file to > > > setup a few registers based on NXP's original 8MM design and reference > > > software. > > > > Can you enable debug on the atf side? > > I can try that. > > > > > Are you using binman to create the image flash.bin? > > Yes.
What's strange to me is that the same flash.bin file behaves differently between the two boot modes. This leads me to believe there is something missing in the setup in order to execute from OCRAM. I attempted to jump directly U-Boot and bypass ATF. U-Boot starts to load, then hangs. The hanging is likely due to the lack of ATF. However, this also tells me that I can load the FIT file, place it into memory and jump to external memory. > > > > > Michael > > > > > > > > adam > > > > > > > > Michael > > > > > > > > > <hang> > > > > > > > > With Debug enabled booting over USB: U-Boot SPL 2022.01-00836-g3cc200c91a-dirty (Jan 31 2022 - 14:55:11 -0600) No pmic WDT: Not starting watchdog@30280000 Trying to boot from USB SDP USB EHCI 1.00 SDP: initialize... SDP: handle requests... Downloading file of size 840280 to 0x40400000... done Jumping to header at 0x40400000 Header Tag is not an IMX image Found header at 0x40417c00 firmware: 'uboot' External data: dst=40200000, offset=3000, size=9ddd8 fdt: 'fdt-1' External data: dst=4029de00, offset=acea8, size=87b0 loadables: 'atf' External data: dst=920000, offset=a0dd8, size=c0ce image entry point: 0x920000 <hang> With Debug Enabled, Booting (same flash.bin file) over MMC: U-Boot SPL 2022.01-00836-g3cc200c91a-dirty (Jan 31 2022 - 14:55:11 -0600) No pmic WDT: Not starting watchdog@30280000 Trying to boot from MMC1 firmware: 'uboot' External data: dst=40200000, offset=3000, size=9ddd8 fdt: 'fdt-1' External data: dst=4029de00, offset=acea8, size=87b0 loadables: 'atf' External data: dst=920000, offset=a0dd8, size=c0ce image entry point: 0x920000 NOTICE: BL31: v2.4(debug):lf-5.10.72-2.2.0-0-g5782363f9 NOTICE: BL31: Built : 14:54:53, Jan 31 2022 INFO: GICv3 with legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 855873 was applied WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing! INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x40200000 INFO: SPSR = 0x3c9 U-Boot 2022.01-00836-g3cc200c91a-dirty (Jan 31 2022 - 14:55:11 -0600) CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz Reset cause: POR Model: Beacon EmbeddedWorks i.MX8M Mini Development Kit DRAM: 2 GiB Core: 99 devices, 21 uclasses, devicetree: separate WDT: Not starting watchdog@30280000 MMC: Invalid usdhc index FSL_SDHC: 3, FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@30890000 Out: serial@30890000 Err: serial@30890000 Net: Warning: ethernet@30be0000 (eth0) using random MAC address - e6:a2:02:0d:23:8b eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 u-boot=> > > > > > > > > -- > > > > Michael Nazzareno Trimarchi > > > > Co-Founder & Chief Executive Officer > > > > M. +39 347 913 2170 > > > > mich...@amarulasolutions.com > > > > __________________________________ > > > > > > > > Amarula Solutions BV > > > > Joop Geesinkweg 125, 1114 AB, Amsterdam, NL > > > > T. +31 (0)85 111 9172 > > > > i...@amarulasolutions.com > > > > www.amarulasolutions.com > > > > > > > > -- > > Michael Nazzareno Trimarchi > > Co-Founder & Chief Executive Officer > > M. +39 347 913 2170 > > mich...@amarulasolutions.com > > __________________________________ > > > > Amarula Solutions BV > > Joop Geesinkweg 125, 1114 AB, Amsterdam, NL > > T. +31 (0)85 111 9172 > > i...@amarulasolutions.com > > www.amarulasolutions.com
