On Fri, Jul 23, 2021 at 10:25 PM Tom Rini <tr...@konsulko.com> wrote: > > On Fri, Jul 23, 2021 at 09:46:44PM -0500, Dennis Gilmore wrote: > > > removing the header is not sufficient to have the boards booting from SPI. > > > > U-Boot TPL 2021.07-00768-g49373a3334-dirty (Jul 23 2021 - 20:42:57) > > Channel 0: LPDDR4, 50MHz > > BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB > > Channel 1: LPDDR4, 50MHz > > BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB > > 256B stride > > lpddr4_set_rate: change freq to 400000000 mhz 0, 1 > > lpddr4_set_rate: change freq to 800000000 mhz 1, 0 > > Trying to boot from BOOTROM > > Returning to boot ROM... > > > > U-Boot SPL 2021.07-00768-g49373a3334-dirty (Jul 23 2021 - 20:42:57 -0500) > > Trying to boot from SPI > > > > At this point u-boot hangs, with the patch reverted I get the following > > U-Boot TPL 2021.07-00769-g4af8bd872c-dirty (Jul 23 2021 - 21:20:51) > > Channel 0: LPDDR4, 50MHz > > BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB > > Channel 1: LPDDR4, 50MHz > > BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB > > 256B stride > > lpddr4_set_rate: change freq to 400000000 mhz 0, 1 > > lpddr4_set_rate: change freq to 800000000 mhz 1, 0 > > Trying to boot from BOOTROM > > Returning to boot ROM... > > > > U-Boot SPL 2021.07-00769-g4af8bd872c-dirty (Jul 23 2021 - 21:20:51 -0500) > > Trying to boot from SPI > > > > > > U-Boot 2021.07-00769-g4af8bd872c-dirty (Jul 23 2021 - 21:20:51 -0500) > > > > SoC: Rockchip rk3399 > > Reset cause: RST > > Model: Kobol Helios64 > > Revision: 0.0 - Unknown > > DRAM: 3.9 GiB > > PMIC: RK808 > > MMC: mmc@fe320000: 1, mmc@fe330000: 0 > > Loading Environment from SPIFlash... SF: Detected w25q128 with page > > size 256 Bytes, erase size 4 KiB, total 16 MiB > > *** Warning - bad CRC, using default environment > > > > In: serial@ff1a0000 > > Out: serial@ff1a0000 > > Err: serial@ff1a0000 > > Model: Kobol Helios64 > > Revision: UNKNOWN > > Net: dw_dm_mdio_init: mdio node is missing, registering legacy mdio > > busNo ethernet found. > > > > starting USB... > > Bus usb@fe900000: usb maximum-speed not found > > Register 2000140 NbrPorts 2 > > Starting the controller > > USB XHCI 1.10 > > scanning bus usb@fe900000 for devices... 2 USB Device(s) found > > scanning usb for storage devices... 0 Storage Device(s) found > > Hit any key to stop autoboot: 0 > > switch to partitions #0, OK > > mmc0(part 0) is current device > > ** No partition table - mmc 0 ** > > Couldn't find partition mmc 0:1 > > switch to partitions #0, OK > > mmc1 is current device > > Scanning mmc 1:1... > > Scanning disk m...@fe320000.blk... > > Scanning disk m...@fe330000.blk... > > ** Unrecognized filesystem type ** > > Found 5 disks > > dw_dm_mdio_init: mdio node is missing, registering legacy mdio > > busdw_dm_mdio_init: mdio node is missing, registering legacy mdio > > busLoading Boot0000 'Fedora' failed > > EFI boot manager: Cannot load any image > > Found EFI removable media binary efi/boot/bootaa64.efi > > Is LTO on, on these platforms? That code in question really should not > be enabled, at all. Like, if you toss an #error in that section of > code, it should still build. It does, right?
It does still build if I put a #error in the middle of it $ grep LTO .config CONFIG_ARCH_SUPPORTS_LTO=y # CONFIG_LTO is not set LTO is not on > -- > Tom
