On Thu, 15 Jul 2021 13:18:59 +0300
Ivan Uvarov <i.uva...@cognitivepilot.com> wrote:
Hi Ivan,
> The Forlinx OKA40i-C devboard makes use of UARTs 0,2,3,4,5 and 7 of the R40
> SoC, of which UART 0 is connected to an RS232 converter, UART 5 routed to
> an RS485 converter, and the rest broken out directly via labeled headers.
> The board also contains a micro-SD slot connected to SDC3.
>
> This patch adds settings to R40's pinmux node for those UARTs that were not
> already mapped, which would allow us to make use of all available UARTs and
> the micro-SD slot on this board in a further patch.
>
> The patch also adds the /omit-if-no-ref/ keyword to the existing nodes for
> UART0 and UART3 for consistency.
Please keep exactly to the files as committed to Linux.
Just copy the file from v5.14-rc1 over, as you did before, on the last
r40.dtsi update - and adjust the subject accordingly (update .dtsi ...).
You can then mention what thing brings and why briefly in the commit
message.
> Signed-off-by: Ivan Uvarov <i.uva...@cognitivepilot.com>
>
> 1 file changed, 43 insertions(+)
Not sure where this line comes from, that's typically not part of the
patch (but created by git on-the-fly, if needed).
Cheers,
Andre
>
> diff --git a/arch/arm/dts/sun8i-r40.dtsi b/arch/arm/dts/sun8i-r40.dtsi
> index d5ad3b9efd..51031a0e59 100644
> --- a/arch/arm/dts/sun8i-r40.dtsi
> +++ b/arch/arm/dts/sun8i-r40.dtsi
> @@ -357,6 +357,8 @@
> clock-names = "ahb", "mmc";
> resets = <&ccu RST_BUS_MMC3>;
> reset-names = "ahb";
> + pinctrl-0 = <&mmc3_pins>;
> + pinctrl-names = "default";
> interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> status = "disabled";
> #address-cells = <1>;
> @@ -601,6 +603,14 @@
> bias-pull-up;
> };
>
> + mmc3_pins: mmc3-pins {
> + pins = "PI4", "PI5", "PI6",
> + "PI7", "PI8", "PI9";
> + function = "mmc3";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> /omit-if-no-ref/
> spi0_pc_pins: spi0-pc-pins {
> pins = "PC0", "PC1", "PC2";
> @@ -631,20 +641,53 @@
> function = "spi1";
> };
>
> + /omit-if-no-ref/
> uart0_pb_pins: uart0-pb-pins {
> pins = "PB22", "PB23";
> function = "uart0";
> };
>
> + /omit-if-no-ref/
> + uart2_pi_pins: uart2-pi-pins {
> + pins = "PI18", "PI19";
> + function = "uart2";
> + };
> +
> + /omit-if-no-ref/
> + uart2_rts_cts_pi_pins: uart2-rts-cts-pi-pins{
> + pins = "PI16", "PI17";
> + function = "uart2";
> + };
> +
> + /omit-if-no-ref/
> uart3_pg_pins: uart3-pg-pins {
> pins = "PG6", "PG7";
> function = "uart3";
> };
>
> + /omit-if-no-ref/
> uart3_rts_cts_pg_pins: uart3-rts-cts-pg-pins {
> pins = "PG8", "PG9";
> function = "uart3";
> };
> +
> + /omit-if-no-ref/
> + uart4_pg_pins: uart4-pg-pins {
> + pins = "PG10", "PG11";
> + function = "uart4";
> + };
> +
> + /omit-if-no-ref/
> + uart5_ph_pins: uart5-ph-pins {
> + pins = "PH6", "PH7";
> + function = "uart5";
> + };
> +
> + /omit-if-no-ref/
> + uart7_pi_pins: uart7-pi-pins {
> + pins = "PI20", "PI21";
> + function = "uart7";
> + };
> };
>
> wdt: watchdog@1c20c90 {
