This patch adds the necessary configs and docs for FPIOA and GPIO support
on the K210.
The board does not boot unless CONSOLE_LOGLEVEL is set to a non-default
value . It also boots when the tree is dirty (and CONSOLE_LOGLEVEL is not
changed). It also boots when changes are made to the device tree and then
committed. I don't know why this happens. These breakages only occur after
bf2fb81ad3.
Signed-off-by: Sean Anderson <sean...@gmail.com>
---
Changes in v5:
- Increase CONSOLE_LOGLEVEL to 5 as a hack to get the board booting again
- Patch 05/12 "gpio: sifive: Use generic reg read function" has been superseded
by commit 2548493ab4.
Changes in v3:
- Document pins 6 and 7 as not set
Changes in v2:
- Remove SPI flash related Kconfig settings
board/sipeed/maix/Kconfig | 9 +++++
configs/sipeed_maix_bitm_defconfig | 2 +
doc/board/sipeed/maix.rst | 64 +++++++++++++++++++++++++++++-
3 files changed, 73 insertions(+), 2 deletions(-)
diff --git a/board/sipeed/maix/Kconfig b/board/sipeed/maix/Kconfig
index 0cdcd32adc..4c42dd2087 100644
--- a/board/sipeed/maix/Kconfig
+++ b/board/sipeed/maix/Kconfig
@@ -44,4 +44,13 @@ config BOARD_SPECIFIC_OPTIONS
imply RESET_SYSCON
imply SYSRESET
imply SYSRESET_SYSCON
+ imply PINCTRL
+ imply PINCONF
+ imply PINCTRL_K210
+ imply DM_GPIO
+ imply DWAPB_GPIO
+ imply SIFIVE_GPIO
+ imply CMD_GPIO
+ imply LED
+ imply LED_GPIO
endif
diff --git a/configs/sipeed_maix_bitm_defconfig
b/configs/sipeed_maix_bitm_defconfig
index 459bf0d530..0b038ff0a1 100644
--- a/configs/sipeed_maix_bitm_defconfig
+++ b/configs/sipeed_maix_bitm_defconfig
@@ -2,6 +2,8 @@ CONFIG_RISCV=y
CONFIG_TARGET_SIPEED_MAIX=y
CONFIG_ARCH_RV64I=y
CONFIG_STACK_SIZE=0x100000
+# FIXME: Dirty hack to get boot working!
+CONFIG_LOGLEVEL=5
# CONFIG_NET is not set
# CONFIG_INPUT is not set
# CONFIG_DM_ETH is not set
diff --git a/doc/board/sipeed/maix.rst b/doc/board/sipeed/maix.rst
index b1894f3a6f..3811eac61f 100644
--- a/doc/board/sipeed/maix.rst
+++ b/doc/board/sipeed/maix.rst
@@ -156,7 +156,7 @@ To run legacy images, use the ``bootm`` command:
Load Address: 80000000
Entry Point: 80000000
- $ picocom -b 115200 /dev/ttyUSB0i
+ $ picocom -b 115200 /dev/ttyUSB0
=> loady
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
C
@@ -187,6 +187,66 @@ To run legacy images, use the ``bootm`` command:
argv[0] = "<NULL>"
Hit any key to exit ...
+Pin Assignment
+--------------
+
+The K210 contains a Fully Programmable I/O Array (FPIOA), which can remap any
of
+its 256 input functions to any any of 48 output pins. The following table has
+the default pin assignments for the BitM.
+
+===== ========== =======
+Pin Function Comment
+===== ========== =======
+IO_0 JTAG_TCLK
+IO_1 JTAG_TDI
+IO_2 JTAG_TMS
+IO_3 JTAG_TDO
+IO_4 UARTHS_RX
+IO_5 UARTHS_TX
+IO_6 Not set
+IO_7 Not set
+IO_8 GPIO_0
+IO_9 GPIO_1
+IO_10 GPIO_2
+IO_11 GPIO_3
+IO_12 GPIO_4 Green LED
+IO_13 GPIO_5 Red LED
+IO_14 GPIO_6 Blue LED
+IO_15 GPIO_7
+IO_16 GPIOHS_0 ISP
+IO_17 GPIOHS_1
+IO_18 I2S0_SCLK MIC CLK
+IO_19 I2S0_WS MIC WS
+IO_20 I2S0_IN_D0 MIC SD
+IO_21 GPIOHS_5
+IO_22 GPIOHS_6
+IO_23 GPIOHS_7
+IO_24 GPIOHS_8
+IO_25 GPIOHS_9
+IO_26 SPI1_D1 MMC MISO
+IO_27 SPI1_SCLK MMC CLK
+IO_28 SPI1_D0 MMC MOSI
+IO_29 GPIOHS_13 MMC CS
+IO_30 GPIOHS_14
+IO_31 GPIOHS_15
+IO_32 GPIOHS_16
+IO_33 GPIOHS_17
+IO_34 GPIOHS_18
+IO_35 GPIOHS_19
+IO_36 GPIOHS_20 Panel CS
+IO_37 GPIOHS_21 Panel RST
+IO_38 GPIOHS_22 Panel DC
+IO_39 SPI0_SCK Panel WR
+IO_40 SCCP_SDA
+IO_41 SCCP_SCLK
+IO_42 DVP_RST
+IO_43 DVP_VSYNC
+IO_44 DVP_PWDN
+IO_45 DVP_HSYNC
+IO_46 DVP_XCLK
+IO_47 DVP_PCLK
+===== ========== =======
+
Over- and Under-clocking
------------------------
@@ -361,5 +421,5 @@ Address Size Description
0x8801C000 0x1000 riscv priv spec 1.9 config
0x8801D000 0x2000 flattened device tree (contains only addresses and
interrupts)
-0x8801f000 0x1000 credits
+0x8801F000 0x1000 credits
========== ========= ===========
--
2.28.0
