Hi Sean,
On Sun, 7 Jun 2020 at 19:27, Sean Anderson <sean...@gmail.com> wrote:
>
> This extends the pinctrl-sandbox driver to support pin muxing, and adds a
> test for that behaviour. The test is done in C and not python (like the
> existing tests for the pinctrl uclass) because it needs to call
> pinctrl_select_state. Another option could be to add a command that
> invokes pinctrl_select_state and then test everything in
> test/py/tests/test_pinmux.py.
>
> The pinctrl-sandbox driver now mimics the way that many pinmux devices
> work. There are two groups of pins which are muxed together, as well as
> four pins which are muxed individually. I have tried to test all normal
> paths. However, very few error cases are explicitly checked for.
>
> Signed-off-by: Sean Anderson <sean...@gmail.com>
> ---
>
> Changes in v2:
> - New
>
> arch/sandbox/dts/test.dts | 45 +++++++--
> drivers/pinctrl/pinctrl-sandbox.c | 155 +++++++++++++++++++++++-------
> test/dm/Makefile | 3 +
> test/py/tests/test_pinmux.py | 36 +++----
> 4 files changed, 178 insertions(+), 61 deletions(-)
>
[..]
> diff --git a/test/dm/Makefile b/test/dm/Makefile
> index 0d1c66fa1e..9e273ee02d 100644
> --- a/test/dm/Makefile
> +++ b/test/dm/Makefile
> @@ -76,4 +76,7 @@ obj-$(CONFIG_DM_RNG) += rng.o
> obj-$(CONFIG_CLK_K210_SET_RATE) += k210_pll.o
> obj-$(CONFIG_SIMPLE_PM_BUS) += simple-pm-bus.o
> obj-$(CONFIG_RESET_SYSCON) += syscon-reset.o
> +ifneq ($(CONFIG_PINMUX),)
> +obj-$(CONFIG_PINCONF) += pinmux.o
I don't see this file in your patch.
> +endif
> endif
> diff --git a/test/py/tests/test_pinmux.py b/test/py/tests/test_pinmux.py
> index 4e6df992a4..0cbbae000c 100644
> --- a/test/py/tests/test_pinmux.py
> +++ b/test/py/tests/test_pinmux.py
> @@ -28,15 +28,15 @@ def test_pinmux_status_all(u_boot_console):
Feel free to convert this to C also if you like. It is faster,
although perhaps not much faster since it only runs a few commands?
> assert ('a6 : gpio output .' in output)
>
> assert ('pinctrl:' in output)
> - assert ('SCL : I2C SCL.' in output)
> - assert ('SDA : I2C SDA.' in output)
> - assert ('TX : Uart TX.' in output)
> - assert ('RX : Uart RX.' in output)
> - assert ('W1 : 1-wire gpio.' in output)
> - assert ('GPIO0 : gpio bias-pull-up input-disable.' in output)
> - assert ('GPIO1 : gpio drive-open-drain.' in output)
> - assert ('GPIO2 : gpio bias-pull-down input-enable.' in output)
> - assert ('GPIO3 : gpio bias-disable.' in output)
> + assert ('P0 : UART TX.' in output)
> + assert ('P1 : UART RX.' in output)
> + assert ('P2 : I2S SCK.' in output)
> + assert ('P3 : I2S SD.' in output)
> + assert ('P4 : I2S WS.' in output)
> + assert ('P5 : GPIO0 bias-pull-up input-disable.' in output)
> + assert ('P6 : GPIO1 drive-open-drain.' in output)
> + assert ('P7 : GPIO2 bias-pull-down input-enable.' in output)
> + assert ('P8 : GPIO3 bias-disable.' in output)
>
> @pytest.mark.buildconfigspec('cmd_pinmux')
> @pytest.mark.boardspec('sandbox')
> @@ -73,12 +73,12 @@ def test_pinmux_status(u_boot_console):
> assert (not 'pinctrl-gpio:' in output)
> assert (not 'pinctrl:' in output)
>
> - assert ('SCL : I2C SCL.' in output)
> - assert ('SDA : I2C SDA.' in output)
> - assert ('TX : Uart TX.' in output)
> - assert ('RX : Uart RX.' in output)
> - assert ('W1 : 1-wire gpio.' in output)
> - assert ('GPIO0 : gpio bias-pull-up input-disable.' in output)
> - assert ('GPIO1 : gpio drive-open-drain.' in output)
> - assert ('GPIO2 : gpio bias-pull-down input-enable.' in output)
> - assert ('GPIO3 : gpio bias-disable.' in output)
> + assert ('P0 : UART TX.' in output)
> + assert ('P1 : UART RX.' in output)
> + assert ('P2 : I2S SCK.' in output)
> + assert ('P3 : I2S SD.' in output)
> + assert ('P4 : I2S WS.' in output)
> + assert ('P5 : GPIO0 bias-pull-up input-disable.' in output)
> + assert ('P6 : GPIO1 drive-open-drain.' in output)
> + assert ('P7 : GPIO2 bias-pull-down input-enable.' in output)
> + assert ('P8 : GPIO3 bias-disable.' in output)
> --
> 2.26.2
>
Regards,
Simon
