Pls remove below warning
edminiv2.c: In function ‘board_init’:
edminiv2.c:93: warning: implicit declaration of function
‘mvsata_ide_initialize_port’
Regards..
Prafulla . ..
___________________________________
From: u-boot-boun...@lists.denx.de [u-boot-boun...@lists.denx.de] On Behalf Of
Albert Aribaud [albert.arib...@free.fr]
Sent: Tuesday, July 13, 2010 5:32 PM
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH V5 4/4] edminiv2: add mvsata_ide and cmd_ide support
Add mvsata_ide port 1 initialization in edminiv2 init code
Add mvsata_ide and cmd_ide configuration in edminiv2 config
Signed-off-by: Albert Aribaud <albert.arib...@free.fr>
---
board/LaCie/edminiv2/edminiv2.c | 7 ++++++
include/configs/edminiv2.h | 46 ++++++++++++++++++++++++++++++++++++++-
2 files changed, 52 insertions(+), 1 deletions(-)
diff --git a/board/LaCie/edminiv2/edminiv2.c b/board/LaCie/edminiv2/edminiv2.c
index 54c0ffe..f0c2110 100644
--- a/board/LaCie/edminiv2/edminiv2.c
+++ b/board/LaCie/edminiv2/edminiv2.c
@@ -88,5 +88,12 @@ int board_init(void)
/* boot parameter start at 256th byte of RAM base */
gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
+#if defined(CONFIG_MVSATA_IDE)
+ /* Enable SATA port 1 if SATA IDE was configured */
+ mvsata_ide_initialize_port(
+ (struct mv_sata_port_registers *)
+ (ORION5X_SATA_BASE+ORION5X_SATA_PORT1_OFFSET));
+#endif
+
return 0;
}
diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index c3d95a0..0c1a8fc 100644
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -52,6 +52,12 @@
#define CONFIG_SYS_HZ 1000
/*
+ * __io is necessary for cmd_ide to compile
+ */
+
+#define __io
+
+/*
* Board-specific values for Orion5x MPP low level init:
* - MPPs 12 to 15 are SATA LEDs (mode 5)
* - Others are GPIO/unused (mode 3 for MPP0, mode 5 for
@@ -60,7 +66,7 @@
#define ORION5X_MPP0_7 0x00000003
#define ORION5X_MPP8_15 0x55550000
-#define ORION5X_MPP16_23 0x00000000
+#define ORION5X_MPP16_23 0x00005555
/*
* Board-specific values for Orion5x GPIO low level init:
@@ -131,6 +137,7 @@
* Commands configuration - using default command set for now
*/
#include <config_cmd_default.h>
+
/*
* Disabling some default commands for staggered bring-up
*/
@@ -138,6 +145,43 @@
#undef CONFIG_CMD_NET /* no net since no eth */
#undef CONFIG_CMD_NFS /* no NFS since no net */
+#define CONFIG_CMD_IDE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+
+/*
+ * ED Mini V2 has an IDE-compatible SATA connector for port 1
+ */
+
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1
+
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
+
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE 4
+
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+
+/*
+ * CONFIG_CMD_IDE requires some #defines for ATA registers
+ */
+
+/* A single bus, a single device */
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE 1
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR ORION5X_SATA_BASE
+/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
+#define CONFIG_SYS_ATA_IDE0_OFFSET ORION5X_SATA_PORT1_OFFSET
+
/*
* Environment variables configurations
*/
--
1.6.4.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
