Hi Heinrich and all,
On 07/11/2019 12:44, Matthias Brugger wrote:
> Hi Heinrich,
>
> adding Alex just in case he knows better, as he wrote the initial code.
>
> On 06/11/2019 01:57, Heinrich Schuchardt wrote:
>> Hello Matthias,
>>
>> Tom reported:
>>
>> Since patch
>> 143256b353c4d2ad1cf5e5e63b38410188b35e49
>> fdt: update bcm283x device tree sources to Linux 5.1-rc6 state
>>
>> the console no longer shows the initial message, e.g. "U-Boot
>> 2020.01-rc1-00159-g73b6e6ad25-dirty". This leads to a failure in
>> automated testing.
>>
>> To find out what is happening I applied the following code change:
>>
>> diff --git a/drivers/serial/serial_bcm283x_mu.c
>> b/drivers/serial/serial_bcm283x_mu.c
>> index bd1d89ec83..395c49c60a 100644
>> --- a/drivers/serial/serial_bcm283x_mu.c
>> +++ b/drivers/serial/serial_bcm283x_mu.c
>> @@ -171,8 +171,11 @@ static int
>> bcm283x_mu_serial_ofdata_to_platdata(struct udevice *dev)
>> fdt_addr_t addr;
>>
>> /* Don't spawn the device if it's not muxed */
>> - if (!bcm283x_is_serial_muxed())
>> + if (!bcm283x_is_serial_muxed()) {
>> + sprintf((void *)0x02400000, "muxed4 false\n");
>> return -ENODEV;
>> + }
>> + sprintf((void *)0x02400010, "muxed5 true");
>>
>> addr = devfdt_get_addr(dev);
>> if (addr == FDT_ADDR_T_NONE)
>> diff --git a/lib/display_options.c b/lib/display_options.c
>> index ec16d75e0e..9d44f49731 100644
>> --- a/lib/display_options.c
>> +++ b/lib/display_options.c
>> @@ -45,6 +45,7 @@ int display_options(void)
>>
>> display_options_get_banner(true, buf, sizeof(buf));
>> printf("%s", buf);
>> + sprintf((void *)0x02400009, "disp5options");
>>
>> return 0;
>> }
>>
>>
>> And see:
>>
>> 02400000: 6d 75 78 65 64 34 20 66 61 64 69 73 70 35 6f 70 muxed4
>> fadisp5op
>> 02400010: 6d 75 78 65 64 35 20 74 72 75 65 00 05 07 06 01 muxed5
>> true.....
>>
>> bcm283x_mu_serial_ofdata_to_platdata() is obviously called twice.
>>
>> The first call is in serial_init(). At that time the GPIOs are not
>> correctly set up to use the serial port. So display_options() fails.
>> After relocation another call call occurs after the GPIOs are set up and
>> this call succeeds.
>>
>> Do you have an idea how to proceed?
>>
>
> After digging a bit, my guess is: in the mentioned devicetree commit you
> change
> the stdout-path from serial0 (pl011) to serial1 (aux-uart).
>
> My guess is, that the FW sets the pin mux to ALT0 which leads
> bcm283x_is_serial_muxed() to fail.
>
> I wasn't able to find where the pinctrl is initialized. Shouldn't that happen
> before we call serial_init()?
>
That was not correct. I found the issue. The patch deletes the reference to
bcm283x-uboot.dtsi which sets soc, uart[01] and pinctrl nodes as dm-pre-reloc.
I'll send a patch for that.
Regards,
Matthias
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
