Hi,
Request your reply on the below request, Could you pls provide me the solution
or anyone faced the same issue.
Am using the latest U-boot.
Thanks ,
ShivBalaji
________________________________________
From: Balaji Sivakumar, ERS, HCLTech
Sent: Thursday, July 01, 2010 8:44 PM
To: u-boot@lists.denx.de
Cc: Balaji Sivakumar, ERS, HCLTech
Subject: Issue in TFTP using LSI Ethernet Phyceiver
Hi,
We are currently working on a hardware board design project for an Industrial
application.
The processor used in TMS320DM6467ZUTA. We are facing an issue with ethernet
interface.
The Ethernet PHYceiver IC interfaced with processor is L-ET1011C2-C-D (Gigabit
Ethernet PHYceiver from LSI).
The Ethernet PHYceiver IC is configured by processor through MDIO interface.
We are able to read all Ethernet PHYceiver IC registers correctly at MD clock
frequency of 4.5 MHz.
The Ethernet PHYceiver IC is connected to RJ-45 port.
When we are connecting cross over cable between our Processor board and the
Test PC,
we could notice LAN connected (speed 100 MBPS) on our Test PC.
We configured separate static IP address for Processor board and Test PC.
When we try to ping, the ping is getting failed (Error message: "HOST is Not
Alive")
I have also tried running the tftp sever in my test pc and typed the tftp in
the command terminal, it is trying to load the file
and it is timing out after some time.
NOTE: The Processor board has same ethernet interface as there in TMS320DM6467
Eval board.
We are able to see the Ethernet PHYceiver IC recognized by the UBOOT.
Pls find bootup message when i power cycle board, it recognizes the Phyceiver.
U-Boot 2009.08 (Jul 01 2010 - 15:45:29)
I2C: ready
DRAM: 256 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ARM Clock :- 297MHz
DDR Clock :- 297MHz
Net: Ethernet PHY ID: 282f014
Ethernet PHY: GENERIC @ 0x01
Hit any key to stop autoboot: 0
Please find environmental variables am setting.
bootdelay=4
baudrate=115200
bootfile="uImage"
addclk=setenv bootargs ${bootargs} clkref=${clkref}
ethact=
filesize=2740C7
bootcmd=nand read 81100000 4a0000 500000; nboot 80700000 0 a0000; bootm
bootargs=console=ttyS0,115200n8 root=/dev/ram rw initrd=0x81100000,16M mem=120M
ip=dhcp
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot 2009.08 (Jul 01 2010 - 15:45:29)
ipaddr=192.168.25.2
serverip=192.168.25.1
subnetmask=255.255.255.0
netmask=255.255.255.0
Request you to provide valuable suggestions to fix our issue.
Regards,
Balaji S
Thanks ,
ShivBalaji
DISCLAIMER:
-----------------------------------------------------------------------------------------------------------------------
The contents of this e-mail and any attachment(s) are confidential and intended
for the named recipient(s) only.
It shall not attach any liability on the originator or HCL or its affiliates.
Any views or opinions presented in
this email are solely those of the author and may not necessarily reflect the
opinions of HCL or its affiliates.
Any form of reproduction, dissemination, copying, disclosure, modification,
distribution and / or publication of
this message without the prior written consent of the author of this e-mail is
strictly prohibited. If you have
received this email in error please delete it and notify the sender
immediately. Before opening any mail and
attachments please check them for viruses and defect.
-----------------------------------------------------------------------------------------------------------------------
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
