Re: [U-Boot] [PATCH v7 7/9] riscv: sifive: fu540: Setup ethaddr env variable using OTP

[Ramon Fried]

On July 11, 2019 7:28:59 AM GMT+03:00, Anup Patel <anup.pa...@wdc.com> wrote:
>
>
>> -----Original Message-----
>> From: Troy Benjegerdes <troy.benjeger...@sifive.com>
>> Sent: Wednesday, July 10, 2019 10:45 PM
>> To: Anup Patel <anup.pa...@wdc.com>; Sagar Karandikar
>> <sagar.karandi...@sifive.com>; Joey Hewitt <j...@joeyhewitt.com>
>> Cc: Rick Chen <r...@andestech.com>; Bin Meng <bmeng...@gmail.com>;
>> Lukas Auer <lukas.a...@aisec.fraunhofer.de>; Simon Glass
>> <s...@chromium.org>; Ramon Fried <rfried....@gmail.com>; Joe
>> Hershberger <joe.hershber...@ni.com>; Palmer Dabbelt
>> <pal...@sifive.com>; Paul Walmsley <paul.walms...@sifive.com>; Atish
>> Patra <atish.pa...@wdc.com>; Alistair Francis
> <alistair.fran...@wdc.com>;
>> U-Boot Mailing List <u-boot@lists.denx.de>
>> Subject: Re: [PATCH v7 7/9] riscv: sifive: fu540: Setup ethaddr env
> variable
>> using OTP
>>
>>
>>
>> > On Jun 23, 2019, at 11:03 PM, Anup Patel <anup.pa...@wdc.com>
> wrote:
>> >
>> > This patch extends SiFive FU540 board support to setup ethaddr env
>> > variable based on board serialnum read from OTP.
>> >
>> > Signed-off-by: Anup Patel <anup.pa...@wdc.com>
>> > ---
>> > board/sifive/fu540/fu540.c | 122
>> +++++++++++++++++++++++++++++++++
>> > configs/sifive_fu540_defconfig | 1 +
>> > 2 files changed, 123 insertions(+)
>> >
>> > diff --git a/board/sifive/fu540/fu540.c
> b/board/sifive/fu540/fu540.c
>> > index 5adc4a3d4a..11daf1a75a 100644
>> > --- a/board/sifive/fu540/fu540.c
>> > +++ b/board/sifive/fu540/fu540.c
>> > @@ -8,6 +8,128 @@
>> >
>> > #include <common.h>
>> > #include <dm.h>
>> > +#include <linux/delay.h>
>> > +#include <linux/io.h>
>> > +
>> > +#ifdef CONFIG_MISC_INIT_R
>> > +
>> > +#define FU540_OTP_BASE_ADDR 0x10070000
>> > +
>> > +struct fu540_otp_regs {
>> > + u32 pa; /* Address input */
>> > + u32 paio; /* Program address input */
>> > + u32 pas; /* Program redundancy cell selection input */
>> > + u32 pce; /* OTP Macro enable input */
>> > + u32 pclk; /* Clock input */
>> > + u32 pdin; /* Write data input */
>> > + u32 pdout; /* Read data output */
>> > + u32 pdstb; /* Deep standby mode enable input (active low) */
>> > + u32 pprog; /* Program mode enable input */
>> > + u32 ptc; /* Test column enable input */
>> > + u32 ptm; /* Test mode enable input */
>> > + u32 ptm_rep;/* Repair function test mode enable input */
>> > + u32 ptr; /* Test row enable input */
>> > + u32 ptrim; /* Repair function enable input */
>> > + u32 pwe; /* Write enable input (defines program cycle) */
>> > +} __packed;
>> > +
>> > +#define BYTES_PER_FUSE 4
>> > +#define NUM_FUSES 0x1000
>> > +
>> > +static int fu540_otp_read(int offset, void *buf, int size) {
>> > + struct fu540_otp_regs *regs = (void __iomem
>> *)FU540_OTP_BASE_ADDR;
>> > + unsigned int i;
>> > + int fuseidx = offset / BYTES_PER_FUSE;
>> > + int fusecount = size / BYTES_PER_FUSE;
>> > + u32 fusebuf[fusecount];
>> > +
>> > + /* check bounds */
>> > + if (offset < 0 || size < 0)
>> > + return -EINVAL;
>> > + if (fuseidx >= NUM_FUSES)
>> > + return -EINVAL;
>> > + if ((fuseidx + fusecount) > NUM_FUSES)
>> > + return -EINVAL;
>> > +
>> > + /* init OTP */
>> > + writel(0x01, &regs->pdstb); /* wake up from stand-by */
>> > + writel(0x01, &regs->ptrim); /* enable repair function */
>> > + writel(0x01, &regs->pce); /* enable input */
>> > +
>> > + /* read all requested fuses */
>> > + for (i = 0; i < fusecount; i++, fuseidx++) {
>> > + writel(fuseidx, &regs->pa);
>> > +
>> > + /* cycle clock to read */
>> > + writel(0x01, &regs->pclk);
>> > + mdelay(1);
>> > + writel(0x00, &regs->pclk);
>> > + mdelay(1);
>> > +
>> > + /* read the value */
>> > + fusebuf[i] = readl(&regs->pdout);
>> > + }
>> > +
>> > + /* shut down */
>> > + writel(0, &regs->pce);
>> > + writel(0, &regs->ptrim);
>> > + writel(0, &regs->pdstb);
>> > +
>> > + /* copy out */
>> > + memcpy(buf, fusebuf, size);
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static u32 fu540_read_serialnum(void) {
>> > + int ret;
>> > + u32 serial[2] = {0};
>> > +
>> > + for (int i = 0xfe * 4; i > 0; i -= 8) {
>> > + ret = fu540_otp_read(i, serial, sizeof(serial));
>> > + if (ret) {
>> > + printf("%s: error reading from OTP\n", __func__);
>> > + break;
>> > + }
>> > + if (serial[0] == ~serial[1])
>> > + return serial[0];
>> > + }
>> > +
>> > + return 0;
>> > +}
>>
>> Please take a look at the DM-enabled SiFive OTP driver submitted by
> Joey
>> Hewitt at https://github.com/sifive/HiFive_U-
>> Boot/commit/6d842765de142b61f847852da7a9ce0d081d770c
>>
>> This Joey's version also sets the ‘serial#’ environment variable,
> while this
>> patch only sets ‘ethaddr'
>
> I am not sure if "serial#" environment variable is a standard U-Boot
> way of advertising serial number of underlying Host.
it's standard.
>
> Where is this used?
looks at fastboot for instance. it uses this env for the USB serial.
Thanks.,
Ramon
>
> Regards,
> Anup

-- 
Sent from my Android device with K-9 Mail. Please excuse my brevity.

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot