Hi Andreas, On 10/06/19 8:44 PM, Andreas Dannenberg wrote: > Hi Faiz, > > On Fri, Jun 07, 2019 at 09:07:32AM +0530, Lokesh Vutla wrote: >> >> >> On 06/06/19 7:24 PM, Faiz Abbas wrote: >>> The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific >>> to arasan/zynq controllers. Add the same to sdhci.h. >>> >>> Also create a common API to set UHS timings in HOST_CONTROL2. >>> >>> Signed-off-by: Faiz Abbas <faiz_ab...@ti.com> >>> Reviewed-by: Tom Rini <tr...@konsulko.com> >>> Tested-by: Lokesh Vutla <lokeshvu...@ti.com> >> >> This is causing build failure for the following defconfig: >> xilinx_zynqmp_zcu104_revA_defconfig >> >> ➜ u-boot git:(master) v78make xilinx_zynqmp_zcu104_revA_defconfig >> HOSTCC scripts/basic/fixdep >> HOSTCC scripts/kconfig/conf.o >> YACC scripts/kconfig/zconf.tab.c >> LEX scripts/kconfig/zconf.lex.c >> HOSTCC scripts/kconfig/zconf.tab.o >> v8 HOSTLD scripts/kconfig/conf >> # >> # configuration written to .config >> # >> ➜ u-boot git:(master) v78make -j4 -s >> drivers/mmc/zynq_sdhci.c: In function ‘arasan_sdhci_execute_tuning’: >> drivers/mmc/zynq_sdhci.c:97:27: error: ‘SDHCI_HOST_CTRL2’ undeclared (first >> use >> in this function); did you mean ‘SDHCI_HOST_CONTROL2’? >> ctrl = sdhci_readw(host, SDHCI_HOST_CTRL2); >> ^~~~~~~~~~~~~~~~ >> SDHCI_HOST_CONTROL2 >> drivers/mmc/zynq_sdhci.c:97:27: note: each undeclared identifier is reported >> only once for each function it appears in >> drivers/mmc/zynq_sdhci.c: In function ‘arasan_sdhci_set_control_reg’: >> drivers/mmc/zynq_sdhci.c:182:27: error: ‘SDHCI_HOST_CTRL2’ undeclared (first >> use >> in this function); did you mean ‘SDHCI_HOST_CONTROL2’? >> reg = sdhci_readw(host, SDHCI_HOST_CTRL2); >> ^~~~~~~~~~~~~~~~ >> SDHCI_HOST_CONTROL2 >> drivers/mmc/zynq_sdhci.c:183:10: error: ‘SDHCI_18V_SIGNAL’ undeclared (first >> use >> in this function); did you mean ‘SDHCI_DIV_HI_MASK’? >> reg |= SDHCI_18V_SIGNAL; >> ^~~~~~~~~~~~~~~~ >> SDHCI_DIV_HI_MASK >> scripts/Makefile.build:278: recipe for target 'drivers/mmc/zynq_sdhci.o' >> failed >> make[2]: *** [drivers/mmc/zynq_sdhci.o] Error 1 >> scripts/Makefile.build:432: recipe for target 'drivers/mmc' failed >> make[1]: *** [drivers/mmc] Error 2 >> Makefile:1582: recipe for target 'drivers' failed >> make: *** [drivers] Error 2 >> make: *** Waiting for unfinished jobs.... >> >> >> Can you fix it and repost the series? > > Can you re-create the issue? > > Just bubbling this up to the top as it is the first series needed for TI K3 > support... >
Running travis on a final version. Will post soon. Thanks, Faiz _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
