Hi Faiz,
On Fri, Jun 07, 2019 at 09:07:32AM +0530, Lokesh Vutla wrote:
>
>
> On 06/06/19 7:24 PM, Faiz Abbas wrote:
> > The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific
> > to arasan/zynq controllers. Add the same to sdhci.h.
> >
> > Also create a common API to set UHS timings in HOST_CONTROL2.
> >
> > Signed-off-by: Faiz Abbas <faiz_ab...@ti.com>
> > Reviewed-by: Tom Rini <tr...@konsulko.com>
> > Tested-by: Lokesh Vutla <lokeshvu...@ti.com>
>
> This is causing build failure for the following defconfig:
> xilinx_zynqmp_zcu104_revA_defconfig
>
> ➜ u-boot git:(master) v78make xilinx_zynqmp_zcu104_revA_defconfig
> HOSTCC scripts/basic/fixdep
> HOSTCC scripts/kconfig/conf.o
> YACC scripts/kconfig/zconf.tab.c
> LEX scripts/kconfig/zconf.lex.c
> HOSTCC scripts/kconfig/zconf.tab.o
> v8 HOSTLD scripts/kconfig/conf
> #
> # configuration written to .config
> #
> ➜ u-boot git:(master) v78make -j4 -s
> drivers/mmc/zynq_sdhci.c: In function ‘arasan_sdhci_execute_tuning’:
> drivers/mmc/zynq_sdhci.c:97:27: error: ‘SDHCI_HOST_CTRL2’ undeclared (first
> use
> in this function); did you mean ‘SDHCI_HOST_CONTROL2’?
> ctrl = sdhci_readw(host, SDHCI_HOST_CTRL2);
> ^~~~~~~~~~~~~~~~
> SDHCI_HOST_CONTROL2
> drivers/mmc/zynq_sdhci.c:97:27: note: each undeclared identifier is reported
> only once for each function it appears in
> drivers/mmc/zynq_sdhci.c: In function ‘arasan_sdhci_set_control_reg’:
> drivers/mmc/zynq_sdhci.c:182:27: error: ‘SDHCI_HOST_CTRL2’ undeclared (first
> use
> in this function); did you mean ‘SDHCI_HOST_CONTROL2’?
> reg = sdhci_readw(host, SDHCI_HOST_CTRL2);
> ^~~~~~~~~~~~~~~~
> SDHCI_HOST_CONTROL2
> drivers/mmc/zynq_sdhci.c:183:10: error: ‘SDHCI_18V_SIGNAL’ undeclared (first
> use
> in this function); did you mean ‘SDHCI_DIV_HI_MASK’?
> reg |= SDHCI_18V_SIGNAL;
> ^~~~~~~~~~~~~~~~
> SDHCI_DIV_HI_MASK
> scripts/Makefile.build:278: recipe for target 'drivers/mmc/zynq_sdhci.o'
> failed
> make[2]: *** [drivers/mmc/zynq_sdhci.o] Error 1
> scripts/Makefile.build:432: recipe for target 'drivers/mmc' failed
> make[1]: *** [drivers/mmc] Error 2
> Makefile:1582: recipe for target 'drivers' failed
> make: *** [drivers] Error 2
> make: *** Waiting for unfinished jobs....
>
>
> Can you fix it and repost the series?
Can you re-create the issue?
Just bubbling this up to the top as it is the first series needed for TI K3
support...
Thanks,
Andreas
>
> Thanks and regards,
> Lokesh
>
>
> > ---
> > drivers/mmc/sdhci.c | 28 ++++++++++++++++++++++++++++
> > drivers/mmc/zynq_sdhci.c | 31 ++-----------------------------
> > include/sdhci.h | 19 ++++++++++++++++++-
> > 3 files changed, 48 insertions(+), 30 deletions(-)
> >
> > diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c
> > index 75e6567631..79edb18fe5 100644
> > --- a/drivers/mmc/sdhci.c
> > +++ b/drivers/mmc/sdhci.c
> > @@ -533,6 +533,34 @@ static void sdhci_set_power(struct sdhci_host *host,
> > unsigned short power)
> > sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
> > }
> >
> > +void sdhci_set_uhs_timing(struct sdhci_host *host)
> > +{
> > + struct mmc *mmc = (struct mmc *)host->mmc;
> > + u32 reg;
> > +
> > + reg = sdhci_readw(host, SDHCI_HOST_CONTROL2);
> > + reg &= ~SDHCI_CTRL_UHS_MASK;
> > +
> > + switch (mmc->selected_mode) {
> > + case UHS_SDR50:
> > + case MMC_HS_52:
> > + reg |= SDHCI_CTRL_UHS_SDR50;
> > + break;
> > + case UHS_DDR50:
> > + case MMC_DDR_52:
> > + reg |= SDHCI_CTRL_UHS_DDR50;
> > + break;
> > + case UHS_SDR104:
> > + case MMC_HS_200:
> > + reg |= SDHCI_CTRL_UHS_SDR104;
> > + break;
> > + default:
> > + reg |= SDHCI_CTRL_UHS_SDR12;
> > + }
> > +
> > + sdhci_writew(host, reg, SDHCI_HOST_CONTROL2);
> > +}
> > +
> > #ifdef CONFIG_DM_MMC
> > static int sdhci_set_ios(struct udevice *dev)
> > {
> > diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c
> > index 08023783de..b39e1d7a19 100644
> > --- a/drivers/mmc/zynq_sdhci.c
> > +++ b/drivers/mmc/zynq_sdhci.c
> > @@ -48,11 +48,6 @@ static const u8 mode2timing[] = {
> > [MMC_HS_200] = MMC_HS200_BUS_SPEED,
> > };
> >
> > -#define SDHCI_HOST_CTRL2 0x3E
> > -#define SDHCI_CTRL2_MODE_MASK 0x7
> > -#define SDHCI_18V_SIGNAL 0x8
> > -#define SDHCI_CTRL_EXEC_TUNING 0x0040
> > -#define SDHCI_CTRL_TUNED_CLK 0x80
> > #define SDHCI_TUNING_LOOP_COUNT 40
> >
> > static void arasan_zynqmp_dll_reset(struct sdhci_host *host, u8 deviceid)
> > @@ -190,30 +185,8 @@ static void arasan_sdhci_set_control_reg(struct
> > sdhci_host *host)
> > }
> >
> > if (mmc->selected_mode > SD_HS &&
> > - mmc->selected_mode <= UHS_DDR50) {
> > - reg = sdhci_readw(host, SDHCI_HOST_CTRL2);
> > - reg &= ~SDHCI_CTRL2_MODE_MASK;
> > - switch (mmc->selected_mode) {
> > - case UHS_SDR12:
> > - reg |= UHS_SDR12_BUS_SPEED;
> > - break;
> > - case UHS_SDR25:
> > - reg |= UHS_SDR25_BUS_SPEED;
> > - break;
> > - case UHS_SDR50:
> > - reg |= UHS_SDR50_BUS_SPEED;
> > - break;
> > - case UHS_SDR104:
> > - reg |= UHS_SDR104_BUS_SPEED;
> > - break;
> > - case UHS_DDR50:
> > - reg |= UHS_DDR50_BUS_SPEED;
> > - break;
> > - default:
> > - break;
> > - }
> > - sdhci_writew(host, reg, SDHCI_HOST_CTRL2);
> > - }
> > + mmc->selected_mode <= UHS_DDR50)
> > + sdhci_set_uhs_timing(host);
> > }
> > #endif
> >
> > diff --git a/include/sdhci.h b/include/sdhci.h
> > index 3dcbc14965..01addb7a60 100644
> > --- a/include/sdhci.h
> > +++ b/include/sdhci.h
> > @@ -144,7 +144,23 @@
> >
> > #define SDHCI_ACMD12_ERR 0x3C
> >
> > -/* 3E-3F reserved */
> > +#define SDHCI_HOST_CONTROL2 0x3E
> > +#define SDHCI_CTRL_UHS_MASK 0x0007
> > +#define SDHCI_CTRL_UHS_SDR12 0x0000
> > +#define SDHCI_CTRL_UHS_SDR25 0x0001
> > +#define SDHCI_CTRL_UHS_SDR50 0x0002
> > +#define SDHCI_CTRL_UHS_SDR104 0x0003
> > +#define SDHCI_CTRL_UHS_DDR50 0x0004
> > +#define SDHCI_CTRL_HS400 0x0005 /* Non-standard */
> > +#define SDHCI_CTRL_VDD_180 0x0008
> > +#define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
> > +#define SDHCI_CTRL_DRV_TYPE_B 0x0000
> > +#define SDHCI_CTRL_DRV_TYPE_A 0x0010
> > +#define SDHCI_CTRL_DRV_TYPE_C 0x0020
> > +#define SDHCI_CTRL_DRV_TYPE_D 0x0030
> > +#define SDHCI_CTRL_EXEC_TUNING 0x0040
> > +#define SDHCI_CTRL_TUNED_CLK 0x0080
> > +#define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000
> >
> > #define SDHCI_CAPABILITIES 0x40
> > #define SDHCI_TIMEOUT_CLK_MASK 0x0000003F
> > @@ -467,6 +483,7 @@ int sdhci_bind(struct udevice *dev, struct mmc *mmc,
> > struct mmc_config *cfg);
> > int add_sdhci(struct sdhci_host *host, u32 f_max, u32 f_min);
> > #endif /* !CONFIG_BLK */
> >
> > +void sdhci_set_uhs_timing(struct sdhci_host *host);
> > #ifdef CONFIG_DM_MMC
> > /* Export the operations to drivers */
> > int sdhci_probe(struct udevice *dev);
> >
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
