Hi Jack,
On 03/29/2019 06:12 PM, Jack Mitchell wrote:
>
> On 29/03/2019 01:09, Kever Yang wrote:
>> Use board_debug_uart_init() for UART iomux init instead of
>> do it in board_init_f, and move the function to soc file so
>> that we can find all the soc/board setting in soc file and
>> use a common board file for all rockchip SoCs later.
>>
>> Signed-off-by: Kever Yang <kever.y...@rock-chips.com>
>> ---
>>
>> arch/arm/mach-rockchip/rk3399-board-spl.c | 50 +----------------------
>> arch/arm/mach-rockchip/rk3399/rk3399.c | 50 +++++++++++++++++++++++
>> 2 files changed, 51 insertions(+), 49 deletions(-)
>>
>> diff --git a/arch/arm/mach-rockchip/rk3399-board-spl.c
>> b/arch/arm/mach-rockchip/rk3399-board-spl.c
>> index 54a4b848a3..800ca80022 100644
>> --- a/arch/arm/mach-rockchip/rk3399-board-spl.c
>> +++ b/arch/arm/mach-rockchip/rk3399-board-spl.c
>> @@ -127,53 +127,6 @@ void secure_timer_init(void)
>> writel(TIMER_EN | TIMER_FMODE, TIMER_CHN10_BASE + TIMER_CONTROL_REG);
>> }
>>
>> -void board_debug_uart_init(void)
>> -{
>> -#define GRF_BASE 0xff770000
>> -#define GPIO0_BASE 0xff720000
>> -#define PMUGRF_BASE 0xff320000
>> - struct rk3399_grf_regs * const grf = (void *)GRF_BASE;
>> -#ifdef CONFIG_TARGET_CHROMEBOOK_BOB
>> - struct rk3399_pmugrf_regs * const pmugrf = (void *)PMUGRF_BASE;
>> - struct rockchip_gpio_regs * const gpio = (void *)GPIO0_BASE;
>> -#endif
>> -
>> -#if defined(CONFIG_DEBUG_UART_BASE) && (CONFIG_DEBUG_UART_BASE ==
>> 0xff180000)
>> - /* Enable early UART0 on the RK3399 */
>> - rk_clrsetreg(&grf->gpio2c_iomux,
>> - GRF_GPIO2C0_SEL_MASK,
>> - GRF_UART0BT_SIN << GRF_GPIO2C0_SEL_SHIFT);
>> - rk_clrsetreg(&grf->gpio2c_iomux,
>> - GRF_GPIO2C1_SEL_MASK,
>> - GRF_UART0BT_SOUT << GRF_GPIO2C1_SEL_SHIFT);
>> -#else
>> -# ifdef CONFIG_TARGET_CHROMEBOOK_BOB
>> - rk_setreg(&grf->io_vsel, 1 << 0);
>> -
>> - /*
>> - * Let's enable these power rails here, we are already running the SPI
>> - * Flash based code.
>> - */
>> - spl_gpio_output(gpio, GPIO(BANK_B, 2), 1); /* PP1500_EN */
>> - spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_B, 2), GPIO_PULL_NORMAL);
>> -
>> - spl_gpio_output(gpio, GPIO(BANK_B, 4), 1); /* PP3000_EN */
>> - spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_B, 4), GPIO_PULL_NORMAL);
>> -#endif /* CONFIG_TARGET_CHROMEBOOK_BOB */
>> -
>> - /* Enable early UART2 channel C on the RK3399 */
>> - rk_clrsetreg(&grf->gpio4c_iomux,
>> - GRF_GPIO4C3_SEL_MASK,
>> - GRF_UART2DGBC_SIN << GRF_GPIO4C3_SEL_SHIFT);
>> - rk_clrsetreg(&grf->gpio4c_iomux,
>> - GRF_GPIO4C4_SEL_MASK,
>> - GRF_UART2DBGC_SOUT << GRF_GPIO4C4_SEL_SHIFT);
>> - /* Set channel C as UART2 input */
>> - rk_clrsetreg(&grf->soc_con7,
>> - GRF_UART_DBG_SEL_MASK,
>> - GRF_UART_DBG_SEL_C << GRF_UART_DBG_SEL_SHIFT);
>> -#endif
>> -}
>>
>> void board_init_f(ulong dummy)
>> {
>> @@ -183,8 +136,7 @@ void board_init_f(ulong dummy)
>> struct rk3399_grf_regs *grf;
>> int ret;
>>
>> -#define EARLY_UART
>> -#ifdef EARLY_UART
>> +#ifdef CONFIG_DEBUG_UART
>> debug_uart_init();
>>
>> # ifdef CONFIG_TARGET_CHROMEBOOK_BOB
>> diff --git a/arch/arm/mach-rockchip/rk3399/rk3399.c
>> b/arch/arm/mach-rockchip/rk3399/rk3399.c
>> index b76ba4ed32..238f79a216 100644
>> --- a/arch/arm/mach-rockchip/rk3399/rk3399.c
>> +++ b/arch/arm/mach-rockchip/rk3399/rk3399.c
>> @@ -57,3 +57,53 @@ int arch_cpu_init(void)
>>
>> return 0;
>> }
>> +
>> +#ifdef CONFIG_DEBUG_UART_BOARD_INIT
>> +void board_debug_uart_init(void)
>> +{
>> +#define GRF_BASE 0xff770000
>> +#define GPIO0_BASE 0xff720000
>> +#define PMUGRF_BASE 0xff320000
>> + struct rk3399_grf_regs * const grf = (void *)GRF_BASE;
>> +#ifdef CONFIG_TARGET_CHROMEBOOK_BOB
>> + struct rk3399_pmugrf_regs * const pmugrf = (void *)PMUGRF_BASE;
>> + struct rockchip_gpio_regs * const gpio = (void *)GPIO0_BASE;
>> +#endif
>> +
>> +#if defined(CONFIG_DEBUG_UART_BASE) && (CONFIG_DEBUG_UART_BASE ==
>> 0xff180000)
>> + /* Enable early UART0 on the RK3399 */
>> + rk_clrsetreg(&grf->gpio2c_iomux,
>> + GRF_GPIO2C0_SEL_MASK,
>> + GRF_UART0BT_SIN << GRF_GPIO2C0_SEL_SHIFT);
>> + rk_clrsetreg(&grf->gpio2c_iomux,
>> + GRF_GPIO2C1_SEL_MASK,
>> + GRF_UART0BT_SOUT << GRF_GPIO2C1_SEL_SHIFT);
>> +#else
>> +# ifdef CONFIG_TARGET_CHROMEBOOK_BOB
>> + rk_setreg(&grf->io_vsel, 1 << 0);
>> +
>> + /*
>> + * Let's enable these power rails here, we are already running the SPI
>> + * Flash based code.
>> + */
>> + spl_gpio_output(gpio, GPIO(BANK_B, 2), 1); /* PP1500_EN */
>> + spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_B, 2), GPIO_PULL_NORMAL);
>> +
>> + spl_gpio_output(gpio, GPIO(BANK_B, 4), 1); /* PP3000_EN */
>> + spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_B, 4), GPIO_PULL_NORMAL);
>> +#endif /* CONFIG_TARGET_CHROMEBOOK_BOB */
> I understand that it's just moving the whole function over, but if I
> understand correctly these are unrelated to the debug_uart_init that the
> commit mentions.
Thanks for your comment, and I just move the whole function as-is,
so I do not want to change the code before I understand it, and I'm not
the one contribute this part.
Thanks,
- Kever
>
>> +
>> + /* Enable early UART2 channel C on the RK3399 */
>> + rk_clrsetreg(&grf->gpio4c_iomux,
>> + GRF_GPIO4C3_SEL_MASK,
>> + GRF_UART2DGBC_SIN << GRF_GPIO4C3_SEL_SHIFT);
>> + rk_clrsetreg(&grf->gpio4c_iomux,
>> + GRF_GPIO4C4_SEL_MASK,
>> + GRF_UART2DBGC_SOUT << GRF_GPIO4C4_SEL_SHIFT);
>> + /* Set channel C as UART2 input */
>> + rk_clrsetreg(&grf->soc_con7,
>> + GRF_UART_DBG_SEL_MASK,
>> + GRF_UART_DBG_SEL_C << GRF_UART_DBG_SEL_SHIFT);
>> +#endif
>> +}
>> +#endif
>>
>
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
