LS1028A Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports
LS1028A QorIQ Architecture processor.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gu...@nxp.com>
Signed-off-by: Rai Harninder <harninder....@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bha...@nxp.com>
Signed-off-by: Bhaskar Upadhaya <bhaskar.upadh...@nxp.com>
---
arch/arm/Kconfig | 11 ++
arch/arm/cpu/armv8/Kconfig | 2 +-
arch/arm/dts/fsl-ls1028a-qds.dts | 16 +++
board/freescale/ls1028a/Kconfig | 39 +++++++
board/freescale/ls1028a/MAINTAINERS | 10 ++
board/freescale/ls1028a/README | 85 +++++++++++++++
board/freescale/ls1028a/ls1028a.c | 89 ++++++++++++++++
configs/ls1028aqds_tfa_defconfig | 61 +++++++++++
include/configs/ls1028aqds.h | 206 ++++++++++++++++++++++++++++++++++++
9 files changed, 518 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/fsl-ls1028a-qds.dts
create mode 100644 configs/ls1028aqds_tfa_defconfig
create mode 100644 include/configs/ls1028aqds.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index aaaf36a..7741ea2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1203,6 +1203,17 @@ config TARGET_LS1012AFRDM
development platform that supports the QorIQ LS1012A
Layerscape Architecture processor.
+config TARGET_LS1028AQDS
+ bool "Support ls1028aqds"
+ select ARCH_LS1028A
+ select ARM64
+ select ARMV8_MULTIENTRY
+ help
+ Support for Freescale LS1028AQDS platform
+ The LS1028A Development System (QDS) is a high-performance
+ development platform that supports the QorIQ LS1028A
+ Layerscape Architecture processor.
+
config TARGET_LS1028ARDB
bool "Support ls1028ardb"
select ARCH_LS1028A
diff --git a/arch/arm/cpu/armv8/Kconfig b/arch/arm/cpu/armv8/Kconfig
index a4fa63b..3e9d47a 100644
--- a/arch/arm/cpu/armv8/Kconfig
+++ b/arch/arm/cpu/armv8/Kconfig
@@ -104,7 +104,7 @@ config PSCI_RESET
!TARGET_LS1012ARDB && !TARGET_LS1012AFRDM && \
!TARGET_LS1012A2G5RDB && !TARGET_LS1012AQDS && \
!TARGET_LS1012AFRWY && \
- !TARGET_LS1028ARDB && \
+ !TARGET_LS1028ARDB && !TARGET_LS1028AQDS && \
!TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \
!TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \
!TARGET_LS2081ARDB && !TARGET_LX2160ARDB && \
diff --git a/arch/arm/dts/fsl-ls1028a-qds.dts b/arch/arm/dts/fsl-ls1028a-qds.dts
new file mode 100644
index 0000000..131fbb7
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1028a-qds.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP ls1028AQDS device tree source
+ *
+ * Copyright 2018-2019 NXP
+ *
+ */
+
+/dts-v1/;
+
+#include "fsl-ls1028a.dtsi"
+
+/ {
+ model = "NXP Layerscape 1028a QDS Board";
+ compatible = "fsl,ls1028a-qds", "fsl,ls1028a";
+};
diff --git a/board/freescale/ls1028a/Kconfig b/board/freescale/ls1028a/Kconfig
index f4733c2..f8c2fe8 100644
--- a/board/freescale/ls1028a/Kconfig
+++ b/board/freescale/ls1028a/Kconfig
@@ -1,3 +1,42 @@
+if TARGET_LS1028AQDS
+
+config SYS_BOARD
+ default "ls1028a"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls1028aqds"
+
+config EMMC_BOOT
+ bool "Support for booting from EMMC"
+ default n
+
+config SYS_TEXT_BASE
+ default 0x96000000 if SD_BOOT || EMMC_BOOT
+ default 0x82000000 if TFABOOT
+ default 0x20100000
+
+if FSL_LS_PPA
+config SYS_LS_PPA_FW_ADDR
+ hex "PPA Firmware Addr"
+ default 0x20400000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1028A
+ default 0x400000 if SYS_LS_PPA_FW_IN_MMC && ARCH_LS1028A
+if CHAIN_OF_TRUST
+config SYS_LS_PPA_ESBC_ADDR
+ hex "PPA header Addr"
+ default 0x20600000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1028A
+endif
+endif
+
+source "board/freescale/common/Kconfig"
+
+endif
+
if TARGET_LS1028ARDB
config SYS_BOARD
diff --git a/board/freescale/ls1028a/MAINTAINERS
b/board/freescale/ls1028a/MAINTAINERS
index f4990a2..8c01bbb 100644
--- a/board/freescale/ls1028a/MAINTAINERS
+++ b/board/freescale/ls1028a/MAINTAINERS
@@ -1,3 +1,13 @@
+LS1028AQDS BOARD
+M: Sudhanshu Gupta <sudhanshu.gu...@nxp.com>
+M: Rai Harninder <harninder....@nxp.com>
+M: Rajesh Bhagat <rajesh.bha...@nxp.com>
+S: Maintained
+F: board/freescale/ls1028a/
+F: include/configs/ls1028a_common.h
+F: include/configs/ls1028aqds.h
+F: configs/ls1028aqds_tfa_defconfig
+
LS1028ARDB BOARD
M: Sudhanshu Gupta <sudhanshu.gu...@nxp.com>
M: Rai Harninder <harninder....@nxp.com>
diff --git a/board/freescale/ls1028a/README b/board/freescale/ls1028a/README
index a3ce859..678b9b5 100644
--- a/board/freescale/ls1028a/README
+++ b/board/freescale/ls1028a/README
@@ -73,6 +73,91 @@ Serial audio interface(SAI)
stereo speakers
- IEEE1588 interface to support audio on SAI4
+QDS Default Switch Settings (1: ON; 0: OFF)
+-------------------------------------------
+For SD Boot
+SW1 : 10000000
+SW2 : 11100110
+SW3 : 00000010
+SW4 : 00000000
+SW5 : 00000000
+SW6 : 00000000
+SW7 : 11110011
+SW8 : 11100000
+SW9 : 10000001
+SW10: 11100000
+
+For FlexSPI Boot
+SW1 : 11110000
+SW2 : 00000110
+SW3 : 00000010
+SW4 : 00000000
+SW5 : 01100000
+SW6 : 01010000
+SW7 : 11110011
+SW8 : 11100000
+SW9 : 10000000
+SW10: 11100000
+
+LS1028AQDS board Overview
+-------------------------
+Processor
+ Two Arm Cortex- A72 processor cores:
+ - Based on 64-bit ARMv8 architecture
+ - Up to 1.3 GHz operation
+ - Single-threaded cores with 48 KB L1 instruction cache and 32 KB L1
+ data cache
+ - Arranged as a single cluster of two cores sharing a single 1 MB L2
+ cache
+DDR memory
+ - Supports data rates of up to 1.6 GT/s for both, DDR4 and DDR3L
+ - Supports a single- or dual-ranked SODIMM or UDIMM connector
+ - 32-bit data and 4-bit ECC
+ - Supports x8/x16 devices
+ - Supports ECC error detection and correction
+ - 1.35 V or 1.2 V DDR power supply, with automatic tracking of VTT, to
+ all devices in case of DDR3L or DDR4, respectively — Power can
+ switch to 1.35 V or 1.2 V, based on the switch settings for DDR3L or
+ DDR4 devices, respectively
+SerDes (Serializer/Deserializer)
+ - Four-lane (0-3) SerDes:
+ - Lane 0: supports PCIe Gen1/2/3 with x1, x2, and x4 operation, 10
+ Gbit SXGMII, 1 Gbit SGMII
+ - Lane 1: supports PCIe Gen1/2/3 with x1, x2, and x4 operation, 1 Gbit
+ SGMII, 10 Gbit QXGMII, 5 Gbit QSGMII, 1 Gbit SGMII
+ - Lane 2: supports PCIe Gen1/2/3 with x1, x2, and x4 operation, 1 Gbit
+ SGMII
+ - Lane 3: supports PCIe Gen1/2/3 with x1, x2, and x4 operation, 1 Gbit
+ SGMII, SATA 2.0/3.0
+ - Four slots on SerDes lanes support PCIe Gen1/2/3, 1 Gbit SGMII
+ add-in cards
+ - Lane 1 connects to a 2x10 connector with SFP+ through a retimer;
+ lane 2 (TX lines) connects to an SMA connector
+ Lane 3 connects to 1x7 header to support SATA devices
+eSDHC
+ - eSDHC1, eSDHC2
+SPI
+ - SPI1 and SPI2 support three onboard SPI flash memory devices:
+ 512 Mbit high-speed flash (with speed of up to 108/54 MHz)
+ memory for storage
+ 4 Mbit low-speed flash memory (with speed of up to 40 MHz)
+ 64 Mbit high-speed flash memory (with speed of up to 104/80
+ MHz)
+ - SPI3 supports one onboard 64 Mbit SPI flash memory (with speed of
+ up to 104/80 MHz)
+ - All memories operate at 1.8 V
+ - A header is provided on SPI1 to test SPI slave mode
+I2C
+ - LS1028A supports eight I2C controllers
+Serial audio interface(SAI)
+ Two SAI ports with audio codec SGTL5000:
+ - Include stereo LINEIN with support for external analog input
+ - Provide headphone and line output
+Display
+ - DisplayPort connector to connect the DP data to a 4K display device
+ (computer monitor)
+ - eDP connector to connect the DP data to a 4K display panel
+
FlexSPI flash memory map valid for both QDS and RDB
Image Flash Offset
RCW+PBI 0x00000000
diff --git a/board/freescale/ls1028a/ls1028a.c
b/board/freescale/ls1028a/ls1028a.c
index 63f8b7f..9d7251e 100644
--- a/board/freescale/ls1028a/ls1028a.c
+++ b/board/freescale/ls1028a/ls1028a.c
@@ -27,6 +27,39 @@
DECLARE_GLOBAL_DATA_PTR;
+int config_board_mux(void)
+{
+#if defined(CONFIG_TARGET_LS1028AQDS) && defined(CONFIG_FSL_QIXIS)
+ u8 reg;
+
+ reg = QIXIS_READ(brdcfg[13]);
+ /* Field| Function
+ * --------------------------------------------------------------
+ * 7-6 | Controls I2C3 routing (net CFG_MUX_I2C3):
+ * I2C3 | 10= Routes {SCL, SDA} to CAN1 transceiver as {TX, RX}.
+ * --------------------------------------------------------------
+ * 5-4 | Controls I2C4 routing (net CFG_MUX_I2C4):
+ * I2C4 |11= Routes {SCL, SDA} to CAN2 transceiver as {TX, RX}.
+ */
+ reg &= ~(0xf0);
+ reg |= 0xb0;
+ QIXIS_WRITE(brdcfg[13], reg);
+
+ reg = QIXIS_READ(brdcfg[15]);
+ /* Field| Function
+ * --------------------------------------------------------------
+ * 7 | Controls the CAN1 transceiver (net CFG_CAN1_STBY):
+ * CAN1 | 0= CAN #1 transceiver enabled
+ * --------------------------------------------------------------
+ * 6 | Controls the CAN2 transceiver (net CFG_CAN2_STBY):
+ * CAN2 | 0= CAN #2 transceiver enabled
+ */
+ reg &= ~(0xc0);
+ QIXIS_WRITE(brdcfg[15], reg);
+#endif
+ return 0;
+}
+
int board_init(void)
{
#ifdef CONFIG_ENV_IS_NOWHERE
@@ -55,6 +88,15 @@ int board_eth_init(bd_t *bis)
return pci_eth_init(bis);
}
+#if defined(CONFIG_ARCH_MISC_INIT)
+int arch_misc_init(void)
+{
+ config_board_mux();
+
+ return 0;
+}
+#endif
+
int board_early_init_f(void)
{
#ifdef CONFIG_SYS_I2C_EARLY_INIT
@@ -195,6 +237,53 @@ int checkboard(void)
}
#endif
+#ifdef CONFIG_TARGET_LS1028AQDS
+int checkboard1(void)
+{
+#ifdef CONFIG_FSL_QIXIS
+ char buf[64];
+#ifndef CONFIG_SD_BOOT
+ u8 sw;
+#endif
+#endif
+
+ puts("Board: LS1028AQDS, boot from ");
+
+#ifdef CONFIG_FSL_QIXIS
+#ifdef CONFIG_SD_BOOT
+ puts("SD\n");
+#else
+
+ sw = QIXIS_READ(brdcfg[0]);
+
+ switch (sw) {
+ case 0x00:
+ printf("Serial NOR flash\n");
+ break;
+ case 0x20:
+ printf("Serial NAND flash\n");
+ break;
+ case 0x60:
+ printf("QSPI Emulator\n");
+ break;
+ default:
+ printf("invalid setting of SW: 0x%x\n", sw);
+ break;
+ }
+#endif
+
+ printf("Sys ID: 0x%02x, Sys Ver: 0x%02x\n",
+ QIXIS_READ(id), QIXIS_READ(arch));
+
+ printf("FPGA: v%d (%s), build %d\n",
+ (int)QIXIS_READ(scver), qixis_read_tag(buf),
+ (int)qixis_read_minor());
+#endif
+
+ return 0;
+}
+#endif
+
#ifdef CONFIG_TARGET_LS1028ARDB
int checkboard1(void)
{
diff --git a/configs/ls1028aqds_tfa_defconfig b/configs/ls1028aqds_tfa_defconfig
new file mode 100644
index 0000000..2a592a0
--- /dev/null
+++ b/configs/ls1028aqds_tfa_defconfig
@@ -0,0 +1,61 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1028AQDS=y
+CONFIG_SYS_FSL_SDHC_CLK_DIV=1
+CONFIG_TFABOOT=y
+CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
+CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=2
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=10
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0
earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m
hugepagesz=2m hugepages=256 video=1920x1080-32@60 cma=256M"
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_CACHE=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1028a-qds"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_DM=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SATA_CEVA=y
+CONFIG_FSL_CAAM=y
+CONFIG_DM_MMC=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_E1000=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_LAYERSCAPE=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_SYS_NS16550=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_DSPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/include/configs/ls1028aqds.h b/include/configs/ls1028aqds.h
new file mode 100644
index 0000000..6e8862f
--- /dev/null
+++ b/include/configs/ls1028aqds.h
@@ -0,0 +1,206 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2019 NXP
+ */
+
+#ifndef __LS1028A_QDS_H
+#define __LS1028A_QDS_H
+
+#include "ls1028a_common.h"
+
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 100000000
+#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
+
+/* DDR */
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
+#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 2
+#define CONFIG_SYS_SDRAM_SIZE 0x80000000
+
+#define CONFIG_QIXIS_I2C_ACCESS
+#define CONFIG_SYS_I2C_EARLY_INIT
+
+/*
+ * QIXIS Definitions
+ */
+#define CONFIG_FSL_QIXIS
+
+#ifdef CONFIG_FSL_QIXIS
+#define QIXIS_BASE 0x7fb00000
+#define QIXIS_BASE_PHYS QIXIS_BASE
+#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_LBMAP_SWITCH 1
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_LBMAP_SHIFT 5
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_SD 0x00
+#define QIXIS_LBMAP_EMMC 0x00
+#define QIXIS_LBMAP_QSPI 0x00
+#define QIXIS_RCW_SRC_SD 0x8
+#define QIXIS_RCW_SRC_EMMC 0x9
+#define QIXIS_RCW_SRC_QSPI 0xf
+#define QIXIS_RST_CTL_RESET 0x31
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#define QIXIS_RST_FORCE_MEM 0x01
+
+#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
+#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_MSEL_GPCM | \
+ CSPR_V)
+#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
+ CSOR_NOR_NOR_MODE_AVD_NOR | \
+ CSOR_NOR_TRHZ_80)
+
+/*
+ * QIXIS Timing parameters for IFC GPCM
+ */
+#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xc) | \
+ FTIM0_GPCM_TEADC(0x20) | \
+ FTIM0_GPCM_TEAHC(0x10))
+#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0x50) | \
+ FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0x8) | \
+ FTIM2_GPCM_TCH(0x8) | \
+ FTIM2_GPCM_TWP(0xf0))
+#define CONFIG_SYS_FPGA_FTIM3 0x0
+#endif
+
+/* RTC */
+#define CONFIG_SYS_RTC_BUS_NUM 1
+#define I2C_MUX_CH_RTC 0xB
+
+/* FlexSPI */
+#ifdef CONFIG_NXP_FSPI
+#define NXP_FSPI_FLASH_SIZE SZ_256M
+#define NXP_FSPI_FLASH_NUM 1
+#endif
+
+/* Store environment at top of flash */
+#define CONFIG_ENV_SIZE 0x2000
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#endif
+
+/* SATA */
+#define CONFIG_SCSI_AHCI_PLAT
+
+#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
+#ifndef CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT2
+#endif
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+/* DSPI */
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_EON
+#endif
+
+#ifndef SPL_NO_ENV
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "board=ls1028aqds\0" \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "fdt_addr=0x00f00000\0" \
+ "kernel_addr=0x01000000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "load_addr=0xa0000000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "ramdisk_addr_r=0xa0000000\0" \
+ "kernel_start=0x1000000\0" \
+ "kernelheader_start=0x800000\0" \
+ "kernel_load=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "kernelheader_size=0x40000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernel_size_sd=0x14000\0" \
+ "kernelhdr_addr_sd=0x4000\0" \
+ "kernelhdr_size_sd=0x10\0" \
+ "console=ttyS0,115200\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
+ BOOTENV \
+ "boot_scripts=ls1028aqds_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1028aqds_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;" \
+ "\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "qspi_bootcmd=echo Trying load from flexspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_start $kernel_size; env exists secureboot " \
+ "&& sf read $kernelheader_addr_r $kernelheader_start " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
+ "bootm $load_addr#$board\0" \
+ "qspi_hdploadcmd=echo Trying load HDP firmware from flexspi..;" \
+ "hdp load 0x20900000 0x2000\0" \
+ "sd_bootcmd=echo Trying load from SD ..;" \
+ "mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd && " \
+ "env exists secureboot && mmc read $kernelheader_addr_r " \
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$board\0" \
+ "sd_hdploadcmd=echo Trying load HDP firmware from SD..;" \
+ "mmcinfo;mmc read $load_addr 0x4800 0x200 " \
+ "&& hdp load $load_addr 0x2000\0" \
+ "emmc_bootcmd=echo Trying load from EMMC ..;" \
+ "mmcinfo; mmc dev 1; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd && " \
+ "env exists secureboot && mmc read $kernelheader_addr_r " \
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$board\0" \
+ "emmc_hdploadcmd=echo Trying load HDP firmware from EMMC..;" \
+ "mmc dev 1;mmcinfo;mmc read $load_addr 0x4800 0x200 "
\
+ "&& hdp load $load_addr 0x2000\0"
+#endif
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+#endif /* __LS1028A_QDS_H */
--
1.9.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
