On Tue, Feb 12, 2019 at 7:14 PM Patrick DELAUNAY
<patrick.delau...@st.com> wrote:
>
> Hi Jagan
>
> > From: Jagan Teki <ja...@amarulasolutions.com>
> > Sent: samedi 9 février 2019 17:22
> > Subject: Re: [PATCH v3] dm: spi: Read default speed and mode values from DT
> >
> > On Mon, Jan 28, 2019 at 2:37 PM Patrick Delaunay <patrick.delau...@st.com>
> > wrote:
> > >
> > > This patch update the behavior introduced by commit 96907c0fe50a ("dm:
> > > spi: Read default speed and mode values from DT")
> > >
> > > In case of DT boot, don't read default speed and mode for SPI from
> > > CONFIG_* but instead read from DT node. This will make sure that
> > > boards with multiple SPI/QSPI controllers can be probed at different
> > > bus frequencies and SPI modes.
> > >
> > > DT values will be always used when available (full DM support of SPI
> > > slave with available DT node) even if speed and mode are requested;
> > > for example in splash screen support (in splash_sf_read_raw) or in SPL
> > > boot (in spl_spi_load_image).
> > > The caller of spi_get_bus_and_cs() no more need to force speed=0.
> > >
> > > But the current behavior don't change if the SPI slave is not present
> > > (device with generic driver is created automatically) or if platdata
> > > is used (CONFIG_OF_PLATDATA).
> > >
> > >
> > > Signed-off-by: Patrick Delaunay <patrick.delau...@st.com>
> > > ---
> > >
> > > Changes in v3:
> > > - complete rework of the patch-set to avoid regression
> > >
> > > Changes in v2:
> > > - use variables to avoid duplicated code
> > >
> > > README | 3 +++
> > > cmd/sf.c | 3 +--
> > > common/spl/spl_spi.c | 2 ++
> > > drivers/spi/spi-uclass.c | 4 +++-
> > > include/spi.h | 9 +++++----
> > > 5 files changed, 14 insertions(+), 7 deletions(-)
> > >
> > > diff --git a/README b/README
> > > index 17d56b8..f7fe74f 100644
> > > --- a/README
> > > +++ b/README
> > > @@ -2184,6 +2184,9 @@ The following options need to be configured:
> > > CONFIG_SF_DEFAULT_MODE (see include/spi.h)
> > > CONFIG_SF_DEFAULT_SPEED in Hz
> > >
> > > + In case of DT boot, SPI don't read default speed and mode
> > > + from CONFIG_*, but from platdata values computed from
> > > available
> > > + DT node
> >
> > This has to update in Kconfig help info.
>
> Ok but witch Kconfig ? whitch config ?
>
> drivers/mtd/spi/Kconfig
> config DM_SPI_FLASH
>
> PS: In master branch, these define are not in yet managed in Kconfig, but
> they are still managed by defines:
> scripts/config_whitelist.txt:1713:CONFIG_SF_DEFAULT_MODE
> And so documentation is done in README not in Kconfig
>
> some migration in Kconfig is pending (moveconfig) ?
Yes, moving them and make changes on top would really nice to go. thanks!
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
