On 31/01/19 7:06 PM, Jagan Teki wrote: [...] > >> configs/xilinx_zynqmp_mini_qspi_defconfig | 1 - > >> configs/xilinx_zynqmp_zc1232_revA_defconfig | 1 - > >> configs/xilinx_zynqmp_zc1254_revA_defconfig | 1 - > >> configs/xilinx_zynqmp_zc1275_revA_defconfig | 1 - > >> configs/xilinx_zynqmp_zc1275_revB_defconfig | 1 - > >> configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 - > >> configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 - > >> configs/xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 - > >> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 - > >> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 - > >> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 - > >> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 - > >> configs/xilinx_zynqmp_zcu104_revA_defconfig | 1 - > >> configs/xilinx_zynqmp_zcu104_revC_defconfig | 1 - > >> configs/xilinx_zynqmp_zcu106_revA_defconfig | 1 - > >> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 - > >> configs/zynq_cc108_defconfig | 1 - > >> configs/zynq_cse_qspi_defconfig | 1 - > >> configs/zynq_dlc20_rev1_0_defconfig | 1 - > >> configs/zynq_microzed_defconfig | 1 - > >> configs/zynq_minized_defconfig | 1 - > >> configs/zynq_z_turn_defconfig | 1 - > >> configs/zynq_zc702_defconfig | 1 - > >> configs/zynq_zc706_defconfig | 1 - > >> configs/zynq_zc770_xm010_defconfig | 1 - > >> configs/zynq_zc770_xm013_defconfig | 1 - > >> configs/zynq_zed_defconfig | 1 - > >> configs/zynq_zybo_defconfig | 1 - > >> configs/zynq_zybo_z7_defconfig | 1 - > > > > zynq targets do need BAR, same has commented in previous mails. > > Hmmm, Is this a limitation of SPI controller on the SoC or flash on the > board? > AFAICS, zynq_spi.c, zynq_qspi.c zynq_spi.c zynqmp_gqspi.c are all FIFO > based SPI controllers and ideally should not care about address length. > Could you please explain why BAR is a requirement on these platforms? > > Were you able to test this series on any of those platforms? > > > Go back to the log history, initial intension for adding BAR was on zynq. >
Sorry, this is all I could find from mailing list (original series by you that adds BAR support): https://lists.denx.de/pipermail/u-boot/2013-June/157006.html There is nothing that mentions why Zynq platforms need BAR support and cannot use 4 byte opcodes to access >16MB space? -- Regards Vignesh _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
