I have tested the series on my pinebook on top of git commit 99431c1c21685fe63d46b6eac995b78ce9adce0a
I am not sure if video is expected to work or not, in my case it does not work. U-Boot SPL 2018.11-rc3-00027-g77a46c3a3c (Nov 03 2018 - 13:42:47 -0500) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v1.6(release): NOTICE: BL31: Built : 09:10:17, Sep 23 2018 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: STUB PMIC setup code called U-Boot 2018.11-rc3-00027-g77a46c3a3c (Nov 03 2018 - 13:42:47 -0500) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Pinebook DRAM: 2 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment Warning: HDMI PHY init timeout! Warning: HDMI PHY init timeout! In: serial Out: serial Err: serial u-boot however works fine and the system is able to boot and the correct dtb is loaded. Tested-by: Dennis Gilmore <den...@ausil.us> El mar, 30-10-2018 a las 14:36 -0700, Vagrant Cascadian escribió: > Tested series applied to u-boot 2018.11-rc3 on pinebook, both with > reboot and cold boot. > > Thanks for all the work on it! > > Tested-by: Vagrant Cascadian <vagr...@debian.org> > > On 2018-10-28, Vasily Khoruzhick wrote: > > This series adds support for the Pinebook, an allwinner A64 laptop > > produced by Pine64. It also syncs sun50i-a64.dtsi with linux, > > adds support for mmc delay calibration, R_I2C controller, > > and addresses the issue with activating video bridge when any of > > GPIOs is missing. > > > > v2: - sync sun50i-a64.dtsi with linux instead of adding missing > > nodes > > - take sun50i-a64-pinebook.dts from linux > > - don't introduce new Kconfig for A64 MMC calibration > > - improve code in video bridge uclass to check for presensce of > > GPIO instead of ingoring EINVAL errors > > v3: - enable calibration for H6 as well > > - init ret variable in video_bridge_set_active() > > - fix order of dts files Makefile > > - split anx6345 binding into sun50i-a64-pinebook-u-boot.dts > > - drop speaker_amp node from pinebook dts > > - drop unnecessary options from defconfig > > v4: - sync device tree files with linux-next > > > > Vasily Khoruzhick (5): > > mmc: sunxi: add support for automatic delay calibration > > dm: video: bridge: don't fail to activate bridge if reset or > > sleep > > GPIO is missing > > sunxi: DT: A64: update device tree files for Allwinner A64 SoC > > sun50i: A64: add support for R_I2C controller > > sunxi: DT: add support for Pinebook > > > > arch/arm/dts/Makefile | 1 + > > arch/arm/dts/sun50i-a64-amarula-relic.dts | 168 +++++++++- > > arch/arm/dts/sun50i-a64-bananapi-m64.dts | 34 +- > > arch/arm/dts/sun50i-a64-nanopi-a64.dts | 89 +++++- > > arch/arm/dts/sun50i-a64-olinuxino.dts | 103 +++++- > > arch/arm/dts/sun50i-a64-orangepi-win.dts | 179 ++++++++++- > > arch/arm/dts/sun50i-a64-pine64.dts | 32 +- > > arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi | 15 + > > arch/arm/dts/sun50i-a64-pinebook.dts | 294 > > +++++++++++++++++ > > arch/arm/dts/sun50i-a64-sopine-baseboard.dts | 32 +- > > arch/arm/dts/sun50i-a64-sopine.dtsi | 15 + > > arch/arm/dts/sun50i-a64.dtsi | 313 > > +++++++++++++++++-- > > arch/arm/include/asm/arch-sunxi/gpio.h | 1 + > > arch/arm/include/asm/arch-sunxi/mmc.h | 6 +- > > arch/arm/mach-sunxi/Kconfig | 1 + > > board/sunxi/board.c | 6 + > > configs/pinebook_defconfig | 22 ++ > > drivers/mmc/sunxi_mmc.c | 21 +- > > drivers/video/bridge/video-bridge-uclass.c | 16 +- > > 19 files changed, 1296 insertions(+), 52 deletions(-) > > create mode 100644 arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi > > create mode 100644 arch/arm/dts/sun50i-a64-pinebook.dts > > create mode 100644 configs/pinebook_defconfig > > > > -- > > 2.19.1 > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > https://lists.denx.de/listinfo/u-boot _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
