From: Andreas Dannenberg <dannenb...@ti.com>

The EEPROM reading in the board detection code is done through legacy
I2C functions which on platforms using DM_I2C this functionality is
provided via the CONFIG_DM_I2C_COMPAT layer. To allow newer platforms
to use the board detection code without relying on CONFIG_DM_I2C_COMPAT
go ahead and add an I2C handling implementation that directly uses the
I2C DM functionality.

Signed-off-by: Andreas Dannenberg <dannenb...@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhib...@ti.com>
---

Changes in v2: None

 board/ti/common/board_detect.c | 54 ++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 52 insertions(+), 2 deletions(-)

diff --git a/board/ti/common/board_detect.c b/board/ti/common/board_detect.c
index c475f10..085e732 100644
--- a/board/ti/common/board_detect.c
+++ b/board/ti/common/board_detect.c
@@ -50,6 +50,7 @@ int __maybe_unused ti_i2c_set_alen(int bus_addr, int 
dev_addr, int alen)
 }
 #endif
 
+#if !defined(CONFIG_DM_I2C) || defined(CONFIG_DM_I2C_COMPAT)
 /**
  * ti_i2c_eeprom_init - Initialize an i2c bus and probe for a device
  * @i2c_bus: i2c bus number to initialize
@@ -94,6 +95,7 @@ static int __maybe_unused ti_i2c_eeprom_read(int dev_addr, 
int offset,
 
        return i2c_read(dev_addr, offset, alen, ep, epsize);
 }
+#endif
 
 /**
  * ti_eeprom_string_cleanup() - Handle eeprom programming errors
@@ -122,9 +124,57 @@ __weak void gpi2c_init(void)
 static int __maybe_unused ti_i2c_eeprom_get(int bus_addr, int dev_addr,
                                            u32 header, u32 size, uint8_t *ep)
 {
-       u32 byte, hdr_read;
+       u32 hdr_read;
        int rc;
 
+#if defined(CONFIG_DM_I2C) && !defined(CONFIG_DM_I2C_COMPAT)
+       struct udevice *dev;
+       struct udevice *bus;
+
+       rc = uclass_get_device_by_seq(UCLASS_I2C, bus_addr, &bus);
+       if (rc)
+               return rc;
+       rc = i2c_get_chip(bus, dev_addr, 1, &dev);
+       if (rc)
+               return rc;
+
+       /*
+        * Read the header first then only read the other contents.
+        */
+       rc = i2c_set_chip_offset_len(dev, 2);
+       if (rc)
+               return rc;
+
+       rc = dm_i2c_read(dev, 0, (uint8_t *)&hdr_read, 4);
+       if (rc)
+               return rc;
+
+       /* Corrupted data??? */
+       if (hdr_read != header) {
+               rc = dm_i2c_read(dev, 0, (uint8_t *)&hdr_read, 4);
+               /*
+                * read the eeprom header using i2c again, but use only a
+                * 1 byte address (some legacy boards need this..)
+                */
+               if (rc) {
+                       rc =  i2c_set_chip_offset_len(dev, 1);
+                       if (rc)
+                               return rc;
+
+                       rc = dm_i2c_read(dev, 0, (uint8_t *)&hdr_read, 4);
+               }
+               if (rc)
+                       return rc;
+       }
+       if (hdr_read != header)
+               return -1;
+
+       rc = dm_i2c_read(dev, 0, ep, size);
+       if (rc)
+               return rc;
+#else
+       u32 byte;
+
        gpi2c_init();
        rc = ti_i2c_eeprom_init(bus_addr, dev_addr);
        if (rc)
@@ -168,7 +218,7 @@ static int __maybe_unused ti_i2c_eeprom_get(int bus_addr, 
int dev_addr,
        rc = i2c_read(dev_addr, 0x0, byte, ep, size);
        if (rc)
                return rc;
-
+#endif
        return 0;
 }
 
-- 
2.7.4

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot

Reply via email to