Hi Stefano,
> -----Original Message-----
> From: Stefano Babic [mailto:sba...@denx.de]
> Sent: 2018年10月5日 18:54
> To: Peng Fan <peng....@nxp.com>; sba...@denx.de; ag...@denx.de
> Cc: u-boot@lists.denx.de; Fabio Estevam <fabio.este...@nxp.com>
> Subject: Re: [PATCH V5 32/32] imx: add i.MX8QXP MEK board support
>
> Hi Peng,
>
> I am fine with most patches of this series.
Thanks.
Anyway, I see that to build the image
> you are using a "fork" of mkimage...
Yes. I am developing the i.MX8X mkimage support in U-Boot.
I think It could catch up next release.
Thanks,
Peng.
>
>
> On 26/09/2018 15:52, Peng Fan wrote:
> > Add i.MX8QXP MEK board support
> > Enabled pinctrl/clk/power domain/mmc/i2c driver.
> > Added README file.
> >
> > Signed-off-by: Peng Fan <peng....@nxp.com>
> > Cc: Stefano Babic <sba...@denx.de>
> > Cc: Fabio Estevam <fabio.este...@nxp.com>
> > Cc: Anatolij Gustschin <ag...@denx.de>
> > ---
> > arch/arm/dts/Makefile | 2 +
> > arch/arm/dts/fsl-imx8qxp-mek.dts | 136
> ++++++++++++++++++++++++++
> > arch/arm/mach-imx/imx8/Kconfig | 13 +++
> > board/freescale/imx8qxp_mek/Kconfig | 14 +++
> > board/freescale/imx8qxp_mek/MAINTAINERS | 6 ++
> > board/freescale/imx8qxp_mek/Makefile | 7 ++
> > board/freescale/imx8qxp_mek/README | 72 ++++++++++++++
> > board/freescale/imx8qxp_mek/imx8qxp_mek.c | 152
> +++++++++++++++++++++++++++++
> > board/freescale/mx8mq_evk/README | 81
> ++++++++++++++++
> > configs/imx8qxp_mek_defconfig | 38 ++++++++
> > include/configs/imx8qxp_mek.h | 156
> ++++++++++++++++++++++++++++++
> > 11 files changed, 677 insertions(+)
> > create mode 100644 arch/arm/dts/fsl-imx8qxp-mek.dts create mode
> > 100644 board/freescale/imx8qxp_mek/Kconfig
> > create mode 100644 board/freescale/imx8qxp_mek/MAINTAINERS
> > create mode 100644 board/freescale/imx8qxp_mek/Makefile
> > create mode 100644 board/freescale/imx8qxp_mek/README
> > create mode 100644 board/freescale/imx8qxp_mek/imx8qxp_mek.c
> > create mode 100644 board/freescale/mx8mq_evk/README create mode
> > 100644 configs/imx8qxp_mek_defconfig create mode 100644
> > include/configs/imx8qxp_mek.h
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index
> > 44ebc50bfa..61598bdfeb 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -452,6 +452,8 @@ dtb-$(CONFIG_MX7) += imx7-colibri.dtb \
> >
> > dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
> >
> > +dtb-$(CONFIG_ARCH_IMX8) += fsl-imx8qxp-mek.dtb
> > +
> > dtb-$(CONFIG_RCAR_GEN3) += \
> > r8a7795-h3ulcb.dtb \
> > r8a7795-salvator-x.dtb \
> > diff --git a/arch/arm/dts/fsl-imx8qxp-mek.dts
> > b/arch/arm/dts/fsl-imx8qxp-mek.dts
> > new file mode 100644
> > index 0000000000..6c3bc1dc4d
> > --- /dev/null
> > +++ b/arch/arm/dts/fsl-imx8qxp-mek.dts
> > @@ -0,0 +1,136 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright 2017-2018 NXP
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "fsl-imx8qxp.dtsi"
> > +
> > +/ {
> > + model = "Freescale i.MX8QXP MEK";
> > + compatible = "fsl,imx8qxp-mek", "fsl,imx8qxp";
> > +
> > + chosen {
> > + bootargs = "console=ttyLP0,115200
> earlycon=lpuart32,0x5a060000,115200";
> > + stdout-path = &lpuart0;
> > + };
> > +
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + reg_usdhc2_vmmc: usdhc2-vmmc {
> > + compatible = "regulator-fixed";
> > + regulator-name = "SD1_SPWR";
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > + gpio = <&gpio4 19 GPIO_ACTIVE_HIGH>;
> > + off-on-delay = <3480>;
> > + enable-active-high;
> > + };
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
> > +
> > + imx8qxp-mek {
> > + pinctrl_hog: hoggrp {
> > + fsl,pins = <
> > + SC_P_MCLK_OUT0_ADMA_ACM_MCLK_OUT0
> 0x0600004c
> > + SC_P_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD
> 0x000514a0
> > + >;
> > + };
> > +
> > + pinctrl_ioexp_rst: ioexp-rst-grp {
> > + fsl,pins = <
> > + SC_P_SPI2_SDO_LSIO_GPIO1_IO01 0x06000021
> > + >;
> > + };
> > +
> > + pinctrl_lpi2c1: lpi1cgrp {
> > + fsl,pins = <
> > + SC_P_USB_SS3_TC1_ADMA_I2C1_SCL 0x06000021
> > + SC_P_USB_SS3_TC3_ADMA_I2C1_SDA 0x06000021
> > + >;
> > + };
> > +
> > + pinctrl_lpuart0: lpuart0grp {
> > + fsl,pins = <
> > + SC_P_UART0_RX_ADMA_UART0_RX 0x06000020
> > + SC_P_UART0_TX_ADMA_UART0_TX 0x06000020
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + SC_P_EMMC0_CLK_CONN_EMMC0_CLK
> 0x06000041
> > + SC_P_EMMC0_CMD_CONN_EMMC0_CMD
> 0x00000021
> > + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0
> 0x00000021
> > + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1
> 0x00000021
> > + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2
> 0x00000021
> > + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3
> 0x00000021
> > + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4
> 0x00000021
> > + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5
> 0x00000021
> > + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6
> 0x00000021
> > + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7
> 0x00000021
> > + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE
> 0x00000041
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_gpio: usdhc2gpiogrp {
> > + fsl,pins = <
> > + SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO19
> > 0x00000021
> > + SC_P_USDHC1_WP_LSIO_GPIO4_IO21
> > 0x00000021
> > + SC_P_USDHC1_CD_B_LSIO_GPIO4_IO22
> > 0x00000021
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + SC_P_USDHC1_CLK_CONN_USDHC1_CLK
> 0x06000041
> > + SC_P_USDHC1_CMD_CONN_USDHC1_CMD
> 0x00000021
> > + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0
> 0x00000021
> > + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1
> 0x00000021
> > + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2
> 0x00000021
> > + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3
> 0x00000021
> > + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT
> 0x00000021
> > + >;
> > + };
> > + };
> > +};
> > +
> > +&lpuart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_lpuart0>;
> > + status = "okay";
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_lpi2c1 &pinctrl_ioexp_rst>;
> > + pinctrl-assert-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + bus-width = <8>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> > + bus-width = <4>;
> > + cd-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
> > + wp-gpios = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> > + vmmc-supply = <®_usdhc2_vmmc>;
> > + status = "okay";
> > +};
> > diff --git a/arch/arm/mach-imx/imx8/Kconfig
> > b/arch/arm/mach-imx/imx8/Kconfig index 28910c1509..0d3a87cd74 100644
> > --- a/arch/arm/mach-imx/imx8/Kconfig
> > +++ b/arch/arm/mach-imx/imx8/Kconfig
> > @@ -10,4 +10,17 @@ config IMX8QXP
> > config SYS_SOC
> > default "imx8"
> >
> > +choice
> > + prompt "i.MX8 board select"
> > + optional
> > +
> > +config TARGET_IMX8QXP_MEK
> > + bool "Support i.MX8QXP MEK board"
> > + select BOARD_LATE_INIT
> > + select IMX8QXP
> > +
> > +endchoice
> > +
> > +source "board/freescale/imx8qxp_mek/Kconfig"
> > +
> > endif
> > diff --git a/board/freescale/imx8qxp_mek/Kconfig
> > b/board/freescale/imx8qxp_mek/Kconfig
> > new file mode 100644
> > index 0000000000..b67300d816
> > --- /dev/null
> > +++ b/board/freescale/imx8qxp_mek/Kconfig
> > @@ -0,0 +1,14 @@
> > +if TARGET_IMX8QXP_MEK
> > +
> > +config SYS_BOARD
> > + default "imx8qxp_mek"
> > +
> > +config SYS_VENDOR
> > + default "freescale"
> > +
> > +config SYS_CONFIG_NAME
> > + default "imx8qxp_mek"
> > +
> > +source "board/freescale/common/Kconfig"
> > +
> > +endif
> > diff --git a/board/freescale/imx8qxp_mek/MAINTAINERS
> > b/board/freescale/imx8qxp_mek/MAINTAINERS
> > new file mode 100644
> > index 0000000000..e9bf0b35a3
> > --- /dev/null
> > +++ b/board/freescale/imx8qxp_mek/MAINTAINERS
> > @@ -0,0 +1,6 @@
> > +i.MX8QXP MEK BOARD
> > +M: Peng Fan <peng....@nxp.com>
> > +S: Maintained
> > +F: board/freescale/imx8qxp_mek/
> > +F: include/configs/imx8qxp_mek.h
> > +F: configs/imx8qxp_mek_defconfig
> > diff --git a/board/freescale/imx8qxp_mek/Makefile
> > b/board/freescale/imx8qxp_mek/Makefile
> > new file mode 100644
> > index 0000000000..f9ee8aeff3
> > --- /dev/null
> > +++ b/board/freescale/imx8qxp_mek/Makefile
> > @@ -0,0 +1,7 @@
> > +#
> > +# Copyright 2017 NXP
> > +#
> > +# SPDX-License-Identifier: GPL-2.0+
> > +#
> > +
> > +obj-y += imx8qxp_mek.o
> > diff --git a/board/freescale/imx8qxp_mek/README
> > b/board/freescale/imx8qxp_mek/README
> > new file mode 100644
> > index 0000000000..7f740894b2
> > --- /dev/null
> > +++ b/board/freescale/imx8qxp_mek/README
> > @@ -0,0 +1,72 @@
> > +U-Boot for the NXP i.MX8QXP EVK board
> > +
> > +Quick Start
> > +===========
> > +
> > +- Build U-Boot
> > +- Build the ARM Trusted firmware binary
> > +- Get scfw_tcm.bin and ahab-container.img
> > +- Get mkimage tool
> > +- Generate flash.bin using imx-mkimage
> > +- Flash the binary into the SD card
> > +- Boot
> > +
> > +Build U-Boot
> > +============
> > +
> > +$ make imx8qxp_mek_defconfig
> > +$ make
> > +
> > +Get and Build the ARM Trusted firmware
> > +======================================
> > +
> > +$ git clone
> > +https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fso
> >
> +urce.codeaurora.org%2Fexternal%2Fimx%2Fimx-atf&data=02%7C01%7C
> pen
> >
> +g.fan%40nxp.com%7C16559bddb09241959d1d08d62ab0de42%7C686ea1d3bc
> 2b4c6f
> >
> +a92cd99c5c301635%7C0%7C0%7C636743336469804902&sdata=IGY1gR
> Mq6v3qs
> > +a5SQQTlMeyPSstvbethL9x%2FfOolL4c%3D&reserved=0
> > +$ cd imx-atf/
> > +$ git checkout origin/imx_4.9.88_imx8qxp_beta2 -b
> > +imx_4.9.88_imx8qxp_beta2 $ make PLAT=imx8qxp bl31
> > +
> > +Get scfw_tcm.bin and ahab-container.img
> > +==============================
> > +
> > +$ wget
> > +https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fww
> >
> +w.nxp.com%2Flgfiles%2FNMG%2FMAD%2FYOCTO%2Fimx-sc-firmware-0.7.bin
> &
> >
> +;data=02%7C01%7Cpeng.fan%40nxp.com%7C16559bddb09241959d1d08d62a
> b0de42
> >
> +%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C6367433364698049
> 02&
> >
> +sdata=KKPP3UvcGXjgGYEyqMfyXfnJ8xCqCMyEzAtW%2FtLfM5I%3D&rese
> rved=0
> > +$ chmod +x imx-sc-firmware-0.7.bin
> > +$ ./imx-sc-firmware-0.7.bin
> > +$ wget
> > +https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fww
> >
> +w.nxp.com%2Flgfiles%2FNMG%2FMAD%2FYOCTO%2Ffirmware-imx-7.6.bin&a
> mp;da
> >
> +ta=02%7C01%7Cpeng.fan%40nxp.com%7C16559bddb09241959d1d08d62ab0
> de42%7C
> >
> +686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636743336469804902&
> amp;sda
> >
> +ta=wrb3TqG9ETCnEAFp4PBBal5BNOuS9tCBbgs2pTpKAnM%3D&reserved
> =0
> > +$ chmod +x firmware-imx-7.6.bin
> > +$ ./firmware-imx-7.6.bin
> > +
> > +Get imx-mkimage tool
> > +==============================
> > +Download the imx-mkimage tool:
> > +
> > +$ git clone
> > +https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fso
> >
> +urce.codeaurora.org%2Fexternal%2Fimx%2Fimx-mkimage%2F&data=02
> %7C0
> >
> +1%7Cpeng.fan%40nxp.com%7C16559bddb09241959d1d08d62ab0de42%7C68
> 6ea1d3b
> >
> +c2b4c6fa92cd99c5c301635%7C0%7C0%7C636743336469804902&sdata=
> R3IioX
> > +Srr0lUpsB%2BLgniD2NakzUHfEoGofBWm321Lb8%3D&reserved=0
> > +$ cd imx-mkimage/
> > +$ git checkout origin/imx_4.9.88_imx8qxp_beta2 -b
> > +imx_4.9.88_imx8qxp_beta2
>
> I took a look at the source code. We cannot even say that this was started by
> NXP, because it is clearly based on the original U-Boot mainline code. Having
> forked it, it is quite bad. We tried in the past to include tools (see i.MX /
> Atmel /
> TI ..) into U-Boot code instead of using external tools, and it is a pity to
> revert
> this back with i.MX8.
>
> This is generally not accepted in mainline - can we revert and integrate this
> imx-mkimage into U-Boot's mkimage tool ?
>
> Best regards,
> Stefano
>
> > +
> > +
> > +Generate flash.bin using imx-mkimage
> > +====================================
> > +
> > +Copy the following binaries to imx-mkimage/iMX8M folder:
> > +
> > +$ cp imx-atf/build/imx8qxp/release/bl31.bin imx-mkimage/iMX8QX/ $ cp
> > +u-boot/u-boot.bin imx-mkimage/iMX8QX/
> > +
> > +Copy the following firmwares to imx-mkimage/iMX8 folder :
> > +
> > +$ cp firmware-imx-7.6/firmware/seco/ahab-container.img
> > +imx-mkimage/iMX8QX/ $ cp imx-sc-firmware-0.7/mx8qx-mek-scfw-tcm.bin
> > +imx-mkimage/iMX8QX/scfw_tcm.bin
> > +
> > +$ cd imx-mkimage/
> > +$ make SOC=iMX8QX flash
> > +
> > +Flash the binary into the SD card
> > +=================================
> > +
> > +Burn the flash.bin binary to SD card offset 32KB:
> > +
> > +$ sudo dd if=iMX8QX/flash.bin of=/dev/sd[x] bs=1024 seek=32
> > +
> > +Boot
> > +====
> > +Set Boot switch SW2: 1100.
> > diff --git a/board/freescale/imx8qxp_mek/imx8qxp_mek.c
> > b/board/freescale/imx8qxp_mek/imx8qxp_mek.c
> > new file mode 100644
> > index 0000000000..051c852c5d
> > --- /dev/null
> > +++ b/board/freescale/imx8qxp_mek/imx8qxp_mek.c
> > @@ -0,0 +1,152 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright 2018 NXP
> > + */
> > +
> > +#include <common.h>
> > +#include <errno.h>
> > +#include <linux/libfdt.h>
> > +#include <environment.h>
> > +#include <fsl_esdhc.h>
> > +#include <asm/io.h>
> > +#include <asm/gpio.h>
> > +#include <asm/arch/clock.h>
> > +#include <asm/arch/sci/sci.h>
> > +#include <asm/arch/imx8-pins.h>
> > +#include <asm/arch/iomux.h>
> > +#include <asm/arch/sys_proto.h>
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +#define GPIO_PAD_CTRL ((SC_PAD_CONFIG_NORMAL <<
> PADRING_CONFIG_SHIFT) | \
> > + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
> > + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
> > + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
> > +
> > +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN <<
> PADRING_CONFIG_SHIFT) | \
> > + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
> > + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
> > + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
> > +
> > +static iomux_cfg_t uart0_pads[] = {
> > + SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
> > + SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL), };
> > +
> > +static void setup_iomux_uart(void)
> > +{
> > + imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads));
> > +}
> > +
> > +int board_early_init_f(void)
> > +{
> > + int ret;
> > + /* Set UART0 clock root to 80 MHz */
> > + sc_pm_clock_rate_t rate = 80000000;
> > +
> > + /* Power up UART0 */
> > + ret = sc_pm_set_resource_power_mode(-1, SC_R_UART_0,
> SC_PM_PW_MODE_ON);
> > + if (ret)
> > + return ret;
> > +
> > + ret = sc_pm_set_clock_rate(-1, SC_R_UART_0, 2, &rate);
> > + if (ret)
> > + return ret;
> > +
> > + /* Enable UART0 clock root */
> > + ret = sc_pm_clock_enable(-1, SC_R_UART_0, 2, true, false);
> > + if (ret)
> > + return ret;
> > +
> > + setup_iomux_uart();
> > +
> > + return 0;
> > +}
> > +
> > +#ifdef CONFIG_MXC_GPIO
> > +#define IOEXP_RESET IMX_GPIO_NR(1, 1)
> > +
> > +static iomux_cfg_t board_gpios[] = {
> > + SC_P_SPI2_SDO | MUX_MODE_ALT(4) |
> MUX_PAD_CTRL(GPIO_PAD_CTRL),
> > + SC_P_ENET0_REFCLK_125M_25M | MUX_MODE_ALT(4) |
> > + MUX_PAD_CTRL(GPIO_PAD_CTRL),
> > +};
> > +
> > +static void board_gpio_init(void)
> > +{
> > + int ret;
> > + struct gpio_desc desc;
> > +
> > + ret = dm_gpio_lookup_name("gpio@1a_3", &desc);
> > + if (ret)
> > + return;
> > +
> > + ret = dm_gpio_request(&desc, "bb_per_rst_b");
> > + if (ret)
> > + return;
> > +
> > + dm_gpio_set_dir_flags(&desc, GPIOD_IS_OUT);
> > + dm_gpio_set_value(&desc, 0);
> > + udelay(50);
> > + dm_gpio_set_value(&desc, 1);
> > +
> > + imx8_iomux_setup_multiple_pads(board_gpios,
> > +ARRAY_SIZE(board_gpios));
> > +
> > + /* enable i2c port expander assert reset line */
> > + gpio_request(IOEXP_RESET, "ioexp_rst");
> > + gpio_direction_output(IOEXP_RESET, 1); } #endif
> > +
> > +int checkboard(void)
> > +{
> > + puts("Board: iMX8QXP MEK\n");
> > +
> > + print_bootinfo();
> > +
> > + return 0;
> > +}
> > +
> > +int board_init(void)
> > +{
> > +#ifdef CONFIG_MXC_GPIO
> > + board_gpio_init();
> > +#endif
> > +
> > + return 0;
> > +}
> > +
> > +void detail_board_ddr_info(void)
> > +{
> > + puts("\nDDR ");
> > +}
> > +
> > +/*
> > + * Board specific reset that is system reset.
> > + */
> > +void reset_cpu(ulong addr)
> > +{
> > + /* TODO */
> > +}
> > +
> > +#ifdef CONFIG_OF_BOARD_SETUP
> > +int ft_board_setup(void *blob, bd_t *bd) {
> > + return 0;
> > +}
> > +#endif
> > +
> > +int board_mmc_get_env_dev(int devno)
> > +{
> > + return devno;
> > +}
> > +
> > +int board_late_init(void)
> > +{
> > +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> > + env_set("board_name", "MEK");
> > + env_set("board_rev", "iMX8QXP");
> > +#endif
> > +
> > + return 0;
> > +}
> > diff --git a/board/freescale/mx8mq_evk/README
> > b/board/freescale/mx8mq_evk/README
> > new file mode 100644
> > index 0000000000..cd7e67eec5
> > --- /dev/null
> > +++ b/board/freescale/mx8mq_evk/README
> > @@ -0,0 +1,81 @@
> > +U-Boot for the NXP i.MX8MQ EVK board
> > +
> > +Quick Start
> > +===========
> > +
> > +- Build U-Boot
> > +- Build the ARM Trusted firmware binary
> > +- Get DDR firmware and mkimage tool
> > +- Generate flash.bin using imx-mkimage
> > +- Flash the binary into the SD card
> > +- Boot
> > +
> > +Build U-Boot
> > +============
> > +
> > +$ make mx8mq_evk_defconfig
> > +$ make
> > +
> > +Get and Build the ARM Trusted firmware
> > +======================================
> > +
> > +$ git clone
> > +https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fso
> >
> +urce.codeaurora.org%2Fexternal%2Fimx%2Fimx-atf&data=02%7C01%7C
> pen
> >
> +g.fan%40nxp.com%7C16559bddb09241959d1d08d62ab0de42%7C686ea1d3bc
> 2b4c6f
> >
> +a92cd99c5c301635%7C0%7C0%7C636743336469804902&sdata=IGY1gR
> Mq6v3qs
> > +a5SQQTlMeyPSstvbethL9x%2FfOolL4c%3D&reserved=0
> > +$ cd imx-atf/
> > +$ git checkout origin/imx_4.9.51_imx8m_beta $ make PLAT=imx8mq bl31
> > +
> > +Get the DDR firmware and mkimage tool
> ==============================
> > +
> > +$ wget
> > +https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fww
> >
> +w.nxp.com%2Flgfiles%2FNMG%2FMAD%2FYOCTO%2Ffirmware-imx-7.2.bin&a
> mp;da
> >
> +ta=02%7C01%7Cpeng.fan%40nxp.com%7C16559bddb09241959d1d08d62ab0
> de42%7C
> >
> +686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636743336469804902&
> amp;sda
> >
> +ta=OExVnUkK7Wn70OaZdd0DL1wijv3b%2F5UWyCarxw3fRcA%3D&reser
> ved=0
> > +$ chmod +x firmware-imx-7.2.bin
> > +$ ./firmware-imx-7.2.bin
> > +
> > +Download the imx-mkimage tool:
> > +
> > +$ git clone
> > +https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fso
> >
> +urce.codeaurora.org%2Fexternal%2Fimx%2Fimx-mkimage%2F&data=02
> %7C0
> >
> +1%7Cpeng.fan%40nxp.com%7C16559bddb09241959d1d08d62ab0de42%7C68
> 6ea1d3b
> >
> +c2b4c6fa92cd99c5c301635%7C0%7C0%7C636743336469804902&sdata=
> R3IioX
> > +Srr0lUpsB%2BLgniD2NakzUHfEoGofBWm321Lb8%3D&reserved=0
> > +$ cd imx-mkimage/
> > +$ git checkout origin/imx_4.9.51_imx8m_beta
> > +
> > +
> > +Generate flash.bin using imx-mkimage
> > +====================================
> > +
> > +Copy the following binaries to imx-mkimage/iMX8M folder:
> > +
> > +$ cp imx-atf/build/imx8mq/release/bl31.bin imx-mkimage/iMX8M/ $ cp
> > +u-boot/u-boot-nodtb.bin imx-mkimage/iMX8M/ $ cp
> > +u-boot/spl/u-boot-spl.bin imx-mkimage/iMX8M/ $ cp
> > +u-boot/arch/arm/dts/fsl-imx8mq-evk.dtb imx-mkimage/iMX8M/
> > +
> > +Copy the following firmwares to imx-mkimage/iMX8 folder :
> > +
> > +$ cp
> > +firmware-imx-7.2/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem.bin
> > +imx-mkimage/iMX8M/ $ cp
> > +firmware-imx-7.2/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem.bin
> > +imx-mkimage/iMX8M/ $ cp
> > +firmware-imx-7.2/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem.bin
> > +imx-mkimage/iMX8M/ $ cp
> > +firmware-imx-7.2/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem.bin
> > +imx-mkimage/iMX8M/
> > +
> > +If you want to run with HDMI, copy signed_hdmi_imx8m.bin to
> imx-mkimage/iMX8M.
> > +
> > +Before generating the flash.bin, transfer the mkimage generated by U-Boot
> to iMX8M folder:
> > +
> > +$ cp u-boot/tools/mkimage imx-mkimage/iMX8M/ $ mv
> > +imx-mkimage/iMX8M/mkimage imx-mkimage/iMX8M/mkimage_uboot
> > +
> > +$ cd imx-mkimage/
> > +$ make SOC=iMX8M flash_spl_uboot
> > +
> > +Or for using HDMI:
> > +
> > +$ make SOC=iMX8M flash_hdmi_spl_uboot
> > +
> > +Flash the binary into the SD card
> > +=================================
> > +
> > +Burn the flash.bin binary to SD card offset 33KB:
> > +
> > +$ sudo dd if=iMX8M/flash.bin of=/dev/sd[x] bs=1024 seek=33
> > +
> > +Boot
> > +====
> > +Set Boot switch SW801: 1100 and Bmode: 10 to boot from Micro SD.
> > diff --git a/configs/imx8qxp_mek_defconfig
> > b/configs/imx8qxp_mek_defconfig new file mode 100644 index
> > 0000000000..873f30c9c5
> > --- /dev/null
> > +++ b/configs/imx8qxp_mek_defconfig
> > @@ -0,0 +1,38 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_IMX8=y
> > +CONFIG_SYS_TEXT_BASE=0x80020000
> > +CONFIG_SYS_MALLOC_F_LEN=0x2000
> > +CONFIG_TARGET_IMX8QXP_MEK=y
> > +CONFIG_NR_DRAM_BANKS=3
> > +CONFIG_BOOTDELAY=3
> > +# CONFIG_CMD_IMPORTENV is not set
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_DHCP=y
> > +CONFIG_CMD_MII=y
> > +CONFIG_CMD_PING=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-mek"
> > +CONFIG_ENV_IS_IN_MMC=y
> > +CONFIG_CLK_IMX8=y
> > +CONFIG_DM_GPIO=y
> > +CONFIG_DM_PCA953X=y
> > +CONFIG_DM_I2C=y
> > +CONFIG_SYS_I2C_IMX_LPI2C=y
> > +CONFIG_I2C_MUX=y
> > +CONFIG_I2C_MUX_PCA954x=y
> > +CONFIG_MISC=y
> > +CONFIG_DM_MMC=y
> > +CONFIG_DM_ETH=y
> > +CONFIG_PINCTRL=y
> > +CONFIG_PINCTRL_IMX8=y
> > +CONFIG_POWER_DOMAIN=y
> > +CONFIG_IMX8_POWER_DOMAIN=y
> > +CONFIG_DM_REGULATOR=y
> > +CONFIG_DM_REGULATOR_FIXED=y
> > +CONFIG_DM_REGULATOR_GPIO=y
> > +CONFIG_DM_SERIAL=y
> > +CONFIG_FSL_LPUART=y
> > +# CONFIG_EFI_LOADER is not set
> > diff --git a/include/configs/imx8qxp_mek.h
> > b/include/configs/imx8qxp_mek.h new file mode 100644 index
> > 0000000000..82553ce790
> > --- /dev/null
> > +++ b/include/configs/imx8qxp_mek.h
> > @@ -0,0 +1,156 @@
> > +/* SPDX-License-Identifier: GPL-2.0+ */
> > +/*
> > + * Copyright 2018 NXP
> > + */
> > +
> > +#ifndef __IMX8QXP_MEK_H
> > +#define __IMX8QXP_MEK_H
> > +
> > +#include <linux/sizes.h>
> > +#include <asm/arch/imx-regs.h>
> > +
> > +#define CONFIG_REMAKE_ELF
> > +
> > +#define CONFIG_BOARD_EARLY_INIT_F
> > +
> > +/* Flat Device Tree Definitions */
> > +#define CONFIG_OF_BOARD_SETUP
> > +
> > +#undef CONFIG_CMD_EXPORTENV
> > +#undef CONFIG_CMD_IMPORTENV
> > +#undef CONFIG_CMD_IMLS
> > +
> > +#undef CONFIG_CMD_CRC32
> > +#undef CONFIG_BOOTM_NETBSD
> > +
> > +#define CONFIG_FSL_ESDHC
> > +#define CONFIG_FSL_USDHC
> > +#define CONFIG_SYS_FSL_ESDHC_ADDR 0
> > +#define USDHC1_BASE_ADDR 0x5B010000
> > +#define USDHC2_BASE_ADDR 0x5B020000
> > +#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
> > +
> > +#define CONFIG_ENV_OVERWRITE
> > +
> > +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> > +
> > +/* GPIO configs */
> > +#define CONFIG_MXC_GPIO
> > +
> > +/* Initial environment variables */
> > +#define CONFIG_EXTRA_ENV_SETTINGS \
> > + "script=boot.scr\0" \
> > + "image=Image\0" \
> > + "panel=NULL\0" \
> > + "console=ttyLP0,${baudrate}
> earlycon=lpuart32,0x5a060000,${baudrate}\0" \
> > + "fdt_addr=0x83000000\0" \
> > + "fdt_high=0xffffffffffffffff\0" \
> > + "boot_fdt=try\0" \
> > + "fdt_file=fsl-imx8qxp-mek.dtb\0" \
> > + "initrd_addr=0x83800000\0" \
> > + "initrd_high=0xffffffffffffffff\0" \
> > + "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
> > + "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
> > + "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
> > + "mmcautodetect=yes\0" \
> > + "mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
> > + "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr}
> ${script};\0" \
> > + "bootscript=echo Running bootscript from mmc ...; " \
> > + "source\0" \
> > + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0"
> \
> > + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
> > + "mmcboot=echo Booting from mmc ...; " \
> > + "run mmcargs; " \
> > + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
> > + "if run loadfdt; then " \
> > + "booti ${loadaddr} - ${fdt_addr}; " \
> > + "else " \
> > + "echo WARN: Cannot load the DT; " \
> > + "fi; " \
> > + "else " \
> > + "echo wait for boot; " \
> > + "fi;\0" \
> > + "netargs=setenv bootargs console=${console} " \
> > + "root=/dev/nfs " \
> > + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
> > + "netboot=echo Booting from net ...; " \
> > + "run netargs; " \
> > + "if test ${ip_dyn} = yes; then " \
> > + "setenv get_cmd dhcp; " \
> > + "else " \
> > + "setenv get_cmd tftp; " \
> > + "fi; " \
> > + "${get_cmd} ${loadaddr} ${image}; " \
> > + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
> > + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
> > + "booti ${loadaddr} - ${fdt_addr}; " \
> > + "else " \
> > + "echo WARN: Cannot load the DT; " \
> > + "fi; " \
> > + "else " \
> > + "booti; " \
> > + "fi;\0"
> > +
> > +#define CONFIG_BOOTCOMMAND \
> > + "mmc dev ${mmcdev}; if mmc rescan; then " \
> > + "if run loadbootscript; then " \
> > + "run bootscript; " \
> > + "else " \
> > + "if run loadimage; then " \
> > + "run mmcboot; " \
> > + "else run netboot; " \
> > + "fi; " \
> > + "fi; " \
> > + "else booti ${loadaddr} - ${fdt_addr}; fi"
> > +
> > +/* Link Definitions */
> > +#define CONFIG_LOADADDR 0x80280000
> > +
> > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> > +
> > +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000
> > +
> > +/* Default environment is in SD */
> > +#define CONFIG_ENV_SIZE 0x1000
> > +#define CONFIG_ENV_OFFSET (64 * SZ_64K)
> > +#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
> > +
> > +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
> > +
> > +/* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board
> */
> > +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
> > +#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2
> */
> > +#define CONFIG_SYS_FSL_USDHC_NUM 2
> > +
> > +/* Size of malloc() pool */
> > +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024))
> * 1024)
> > +
> > +#define CONFIG_SYS_SDRAM_BASE 0x80000000
> > +#define PHYS_SDRAM_1 0x80000000
> > +#define PHYS_SDRAM_2 0x880000000
> > +#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */
> > +/* LPDDR4 board total DDR is 3GB */
> > +#define PHYS_SDRAM_2_SIZE 0x40000000 /* 1 GB */
> > +
> > +/* Serial */
> > +#define CONFIG_BAUDRATE 115200
> > +
> > +/* Monitor Command Prompt */
> > +#define CONFIG_HUSH_PARSER
> > +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> > +#define CONFIG_SYS_CBSIZE 2048
> > +#define CONFIG_SYS_MAXARGS 64
> > +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> > +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
> > + sizeof(CONFIG_SYS_PROMPT) + 16)
> > +
> > +/* Generic Timer Definitions */
> > +#define COUNTER_FREQUENCY 8000000 /* 8MHz */
> > +
> > +#ifndef CONFIG_DM_PCA953X
> > +#define CONFIG_PCA953X
> > +#define CONFIG_CMD_PCA953X
> > +#define CONFIG_CMD_PCA953X_INFO
> > +#endif
> > +
> > +#endif /* __IMX8QXP_MEK_H */
> >
>
>
> --
> ================================================================
> =====
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
> ================================================================
> =====
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
