On 25.7.2018 23:18, York Sun wrote:
> On 07/24/2018 10:58 PM, Michal Simek wrote:
>> On 24.7.2018 18:26, York Sun wrote:
>>> On 07/24/2018 06:07 AM, Michal Simek wrote:
>>>> There is no reason to limit gzip usage only for OS_BOOT and kernel image
>>>> type.
>>>>
>>>> Signed-off-by: Michal Simek <michal.si...@xilinx.com>
>>>> ---
>>>>
>>>> common/spl/spl_fit.c | 5 +----
>>>> 1 file changed, 1 insertion(+), 4 deletions(-)
>>>>
>>>> diff --git a/common/spl/spl_fit.c b/common/spl/spl_fit.c
>>>> index 9eabb1c1058b..dbf5ac33a845 100644
>>>> --- a/common/spl/spl_fit.c
>>>> +++ b/common/spl/spl_fit.c
>>>> @@ -257,10 +257,7 @@ static int spl_load_fit_image(struct spl_load_info
>>>> *info, ulong sector,
>>>> board_fit_image_post_process(&src, &length);
>>>> #endif
>>>>
>>>> - if (IS_ENABLED(CONFIG_SPL_OS_BOOT) &&
>>>> - IS_ENABLED(CONFIG_SPL_GZIP) &&
>>>> - image_comp == IH_COMP_GZIP &&
>>>> - type == IH_TYPE_KERNEL) {
>>>> + if (IS_ENABLED(CONFIG_SPL_GZIP) && image_comp == IH_COMP_GZIP) {
>>>> size = length;
>>>> if (gunzip((void *)load_addr, CONFIG_SYS_BOOTM_LEN,
>>>> src, &size)) {
>>>>
>>>
>>> This will uncompress ramdisk unnecessarily.
>>
>> Can you please share your its fragment? Also is there any other image
>> which should be exclude?
>
> I used it for falcon boot. I guess the executable image should have "entry".
> In
> my setup, only kernel image has "entry". Here is my its file.
>
> /dts-v1/;
>
> / {
> description = "Image file for the LS1046A Linux Kernel";
> #address-cells = <1>;
>
> images {
> kernel@1 {
> description = "ARM64 Linux kernel";
> data = /incbin/("./arch/arm64/boot/Image.gz");
> type = "kernel";
> arch = "arm64";
> os = "linux";
> compression = "gzip";
> load = <0x80080000>;
> entry = <0x80080000>;
> };
> fdt@1 {
> description = "Flattened Device Tree blob";
> data = /incbin/("./fsl-ls1046ardb.dtb");
> type = "flat_dt";
> arch = "arm64";
> compression = "none";
> load = <0x90000000>;
> };
> ramdisk@1 {
> description = "Buildroot initramfs";
> data = /incbin/("./rootfs.cpio.gz");
> type = "ramdisk";
> arch = "arm64";
> os = "linux";
> compression = "gzip";
I have tested full u-boot and there is also no uncompression for ramdisk
when you put gzip compress there.
I have even tried gzip compression for fdt with expectation that u-boot
will uncompress it.
Based on doc/uImage.FIT/source_file_format.txt:
165 - compression : Compression used by included data. Supported
compressions
166 are "gzip" and "bzip2". If no compression is used compression
property
167 should be set to "none".
Based on me this means that data inside fit are compressed and you are
asking u-boot in boot to uncompress it. If you are not asking for that
you should put none there.
But it doesn't look like this is supported at all for fdt/ramdisk and it
is only handled for OS.
I see here two cases.
1. I want u-boot to uncompress my data in fit image (whatever it is)
before passing control to OS that's why I putting there compression method.
2. I want OS to uncompress data but I want pass this data unchanged from
u-boot to OS that's why I am putting compression method at "none"
I am expecting when you put "none" there than you will boot in falcon
mode without any issue.
I have no problem to change this patch and include only kernel and fpga
image but it sounds to me that we have gaps in implementation that not
all images inside the fit image have the same range of functionalities.
Also I think that "load" entry is that one which matters not "entry".
Thanks,
Michal
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
