Hi Joe, Can you please review these changes ?
Regards, Pankaj Bansal > -----Original Message----- > From: Prabhakar Kushwaha > Sent: Thursday, July 19, 2018 9:06 AM > To: Pankaj Bansal <pankaj.ban...@nxp.com>; u-boot@lists.denx.de > Cc: Priyanka Jain <priyanka.j...@nxp.com>; Varun Sethi > <v.se...@nxp.com>; York Sun <york....@nxp.com>; > joe.hershber...@ni.com > Subject: RE: [PATCH 0/6] driver: net: fsl-mc: Add support of multiple phys > for dpmac > > > > -----Original Message----- > > From: Pankaj Bansal > > Sent: Friday, July 13, 2018 8:11 PM > > To: u-boot@lists.denx.de > > Cc: Prabhakar Kushwaha <prabhakar.kushw...@nxp.com>; Priyanka Jain > > <priyanka.j...@nxp.com>; Varun Sethi <v.se...@nxp.com>; York Sun > > <york....@nxp.com>; joe.hershber...@ni.com; Pankaj Bansal > > <pankaj.ban...@nxp.com> > > Subject: [PATCH 0/6] driver: net: fsl-mc: Add support of multiple phys > > for dpmac > > > > This patch set adds support of multiple phys for one dpmac > > > > Till now we have had cases where we had one phy device per dpmac. > > Now, with the upcoming products (LX2160AQDS), we have cases, where > > there are sometimes two phy devices for one dpmac. One phy for TX > > lanes and one phy for RX lanes. To handle such cases, add the support > > for multiple phys in ethernet driver. The ethernet link is up if all > > the phy devices connected to one dpmac report link up. > > also the link capabilities are limited by the weakest phy device. > > > > i.e. say if there are two phys for one dpmac. one operates at 10G > > without autoneg and other operate at 1G with autoneg. Then the > > ethernet interface will operate at 1G without autoneg. > > > > Pankaj Bansal (6): > > driver: net: fsl-mc: modify the label name > > driver: net: fsl-mc: remove unused strcture elements > > driver: net: fsl-mc: fix error handing in init_phy > > driver: net: fsl-mc: Modify the dpmac link detection method > > driver: net: fsl-mc: initialize dpmac irrespective of phy > > driver: net: fsl-mc: Add support of multiple phys for dpmac > > > > board/freescale/ls1088a/eth_ls1088aqds.c | 18 +-- > > board/freescale/ls1088a/eth_ls1088ardb.c | 21 +-- > > board/freescale/ls2080aqds/eth.c | 26 +-- > > board/freescale/ls2080ardb/eth_ls2080rdb.c | 24 +-- > > drivers/net/fsl-mc/mc.c | 6 +- > > drivers/net/ldpaa_eth/ldpaa_eth.c | 180 +++++++++++++-------- > > drivers/net/ldpaa_eth/ldpaa_eth.h | 1 - > > drivers/net/ldpaa_eth/ldpaa_wriop.c | 49 ++++-- > > include/fsl-mc/ldpaa_wriop.h | 22 +-- > > 9 files changed, 209 insertions(+), 138 deletions(-) > > Patch set looks good. > > Reviewed-by: Prabhakar Kushwaha <prabhakar.kushw...@nxp.com> > > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
