Hi Philipp,
在 2018年02月19日 03:00, Philipp Tomsich 写道:
On Sat, 3 Feb 2018, David Wu wrote:
When the boot ROM sets up MMC we don't need to do it again. Remove the
MMC setup code entirely, but we also need to enable uart for debug
message.
If the MMC always set up correctly for all configurations (e.g. bus-width)
or should some of the setup be duplicated there to ensure that we catch
all corner cases?
For this, I will do a check if we need to setup duplicated.
Signed-off-by: David Wu <david...@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.toms...@theobroma-systems.com>
---
arch/arm/mach-rockchip/rk3188-board-spl.c | 42
+++----------------------------
1 file changed, 3 insertions(+), 39 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3188-board-spl.c
b/arch/arm/mach-rockchip/rk3188-board-spl.c
index 8e3b8ae..8371a31 100644
--- a/arch/arm/mach-rockchip/rk3188-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3188-board-spl.c
@@ -100,10 +100,11 @@ static int setup_arm_clock(void)
void board_init_f(ulong dummy)
{
- struct udevice *pinctrl, *dev;
+ struct udevice *dev;
int ret;
/* Example code showing how to enable the debug UART on RK3188 */
+#define EARLY_UART
#ifdef EARLY_UART
#include <asm/arch/grf_rk3188.h>
/* Enable early UART on the RK3188 */
@@ -124,10 +125,7 @@ void board_init_f(ulong dummy)
* printascii("string");
*/
debug_uart_init();
- printch('s');
- printch('p');
- printch('l');
- printch('\n');
+ printascii("U-Boot SPL board init");
#endif
ret = spl_early_init();
@@ -144,12 +142,6 @@ void board_init_f(ulong dummy)
return;
}
- ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
- if (ret) {
- debug("Pinctrl init failed: %d\n", ret);
- return;
- }
-
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret) {
debug("DRAM init failed: %d\n", ret);
@@ -187,7 +179,6 @@ static int setup_led(void)
void spl_board_init(void)
{
- struct udevice *pinctrl;
int ret;
ret = setup_led();
@@ -196,36 +187,9 @@ void spl_board_init(void)
hang();
}
- ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
- if (ret) {
- debug("%s: Cannot find pinctrl device\n", __func__);
- goto err;
- }
-
-#ifdef CONFIG_SPL_MMC_SUPPORT
- ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
- if (ret) {
- debug("%s: Failed to set up SD card\n", __func__);
- goto err;
- }
-#endif
-
- /* Enable debug UART */
- ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
- if (ret) {
- debug("%s: Failed to set up console UART\n", __func__);
- goto err;
- }
-
preloader_console_init();
#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
back_to_bootrom(BROM_BOOT_NEXTSTAGE);
#endif
return;
-
-err:
- printf("spl_board_init: Error %d\n", ret);
-
- /* No way to report error here */
- hang();
}
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
