On Mon, Jan 22, 2018 at 09:20:06AM +0100, Code Kipper wrote:
> On 22 January 2018 at 09:04, Maxime Ripard
> <maxime.rip...@free-electrons.com> wrote:
> > Hi,
> >
> > On Sun, Jan 21, 2018 at 07:06:49PM +0100, codekip...@gmail.com wrote:
> >> From: Marcus Cooper <codekip...@gmail.com>
> >>
> >> The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> >> 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using
> >> the SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, a dual
> >> colour LED, an IR receiver and an optical S/PDIF connector.
> >>
> >> Signed-off-by: Marcus Cooper <codekip...@gmail.com>
> >> ---
> >> arch/arm/dts/Makefile | 1 +
> >> arch/arm/dts/sun8i-h3-beelink-x2.dts | 155
> >> +++++++++++++++++++++++++++++++++++
> >> board/sunxi/MAINTAINERS | 5 ++
> >> configs/beelink_x2_defconfig | 18 ++++
> >> 4 files changed, 179 insertions(+)
> >> create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
> >> create mode 100644 configs/beelink_x2_defconfig
> >>
> >> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> >> index 9540ba4313..f899cef7ac 100644
> >> --- a/arch/arm/dts/Makefile
> >> +++ b/arch/arm/dts/Makefile
> >> @@ -335,6 +335,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \
> >> dtb-$(CONFIG_MACH_SUN8I_H3) += \
> >> sun8i-h2-plus-orangepi-zero.dtb \
> >> sun8i-h3-bananapi-m2-plus.dtb \
> >> + sun8i-h3-beelink-x2.dtb \
> >> sun8i-h3-libretech-all-h3-cc.dtb \
> >> sun8i-h3-orangepi-2.dtb \
> >> sun8i-h3-orangepi-lite.dtb \
> >> diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
> >> b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> >> new file mode 100644
> >> index 0000000000..43f67eb8db
> >> --- /dev/null
> >> +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> >> @@ -0,0 +1,155 @@
> >> +/*
> >> + * Copyright (C) 2017 Marcus Cooper <codekip...@gmail.com>
> >> + *
> >> + * This file is dual-licensed: you can use it either under the terms
> >> + * of the GPL or the X11 license, at your option. Note that this dual
> >> + * licensing only applies to this file, and not this project as a
> >> + * whole.
> >> + *
> >> + * a) This file is free software; you can redistribute it and/or
> >> + * modify it under the terms of the GNU General Public License as
> >> + * published by the Free Software Foundation; either version 2 of the
> >> + * License, or (at your option) any later version.
> >> + *
> >> + * This file is distributed in the hope that it will be useful,
> >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >> + * GNU General Public License for more details.
> >> + *
> >> + * Or, alternatively,
> >> + *
> >> + * b) Permission is hereby granted, free of charge, to any person
> >> + * obtaining a copy of this software and associated documentation
> >> + * files (the "Software"), to deal in the Software without
> >> + * restriction, including without limitation the rights to use,
> >> + * copy, modify, merge, publish, distribute, sublicense, and/or
> >> + * sell copies of the Software, and to permit persons to whom the
> >> + * Software is furnished to do so, subject to the following
> >> + * conditions:
> >> + *
> >> + * The above copyright notice and this permission notice shall be
> >> + * included in all copies or substantial portions of the Software.
> >> + *
> >> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> >> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> >> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> >> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> >> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> >> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> >> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> >> + * OTHER DEALINGS IN THE SOFTWARE.
> >> + */
> >> +
> >> +/dts-v1/;
> >> +#include "sun8i-h3.dtsi"
> >> +#include "sunxi-common-regulators.dtsi"
> >> +
> >> +#include <dt-bindings/gpio/gpio.h>
> >> +#include <dt-bindings/input/input.h>
> >> +
> >> +/ {
> >> + model = "Beelink X2";
> >> + compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
> >> +
> >> + aliases {
> >> + serial0 = &uart0;
> >> + /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
> >> + ethernet1 = &sdiowifi;
> >> + };
> >> +
> >> + chosen {
> >> + stdout-path = "serial0:115200n8";
> >> + };
> >> +
> >> + leds {
> >> + compatible = "gpio-leds";
> >> +
> >> + blue {
> >> + label = "beelink-x2:blue:pwr";
> >> + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
> >> + default-state = "on";
> >> + };
> >> +
> >> + red {
> >> + label = "beelink-x2:red:standby";
> >> + gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
> >> + };
> >> + };
> >> +
> >> + wifi_pwrseq: wifi_pwrseq {
> >> + compatible = "mmc-pwrseq-simple";
> >> + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> >> + };
> >> +};
> >> +
> >> +&ehci1 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&emac {
> >> + phy = <&phy1>;
> >> + phy-mode = "mii";
> >> + allwinner,use-internal-phy;
> >> + allwinner,leds-active-low;
> >> + status = "okay";
> >> + phy1: ethernet-phy@1 {
> >> + reg = <1>;
> >> + };
> >> +};
> >> +
> >> +&ir {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&ir_pins_a>;
> >> + status = "okay";
> >> +};
> >> +
> >> +&mmc0 {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> >> + vmmc-supply = <®_vcc3v3>;
> >> + bus-width = <4>;
> >> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> >> + cd-inverted;
> >> + status = "okay";
> >> +};
> >> +
> >> +&mmc1 {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&mmc1_pins_a>;
> >> + vmmc-supply = <®_vcc3v3>;
> >> + bus-width = <4>;
> >> + non-removable;
> >> + status = "okay";
> >> +
> >> + /*
> >> + * Explicitly define the sdio device, so that we can add an ethernet
> >> + * alias for it (which e.g. makes u-boot set a mac-address).
> >> + */
> >> + sdiowifi: sdio_wifi@1 {
> >> + reg = <1>;
> >> + };
> >> +};
> >> +
> >> +&mmc2 {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&mmc2_8bit_pins>;
> >> + vmmc-supply = <®_vcc3v3>;
> >> + bus-width = <8>;
> >> + non-removable;
> >> + cap-mmc-hw-reset;
> >> + status = "okay";
> >> +};
> >> +
> >> +&ohci1 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&uart0 {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&uart0_pins_a>;
> >> + status = "okay";
> >> +};
> >> +
> >> +&usbphy {
> >> + status = "okay";
> >> +};
> >
> > Where is that DT coming from? The one in Linux looks different.
> Hi Maxime,
> I stripped out the bits which haven't been included in uboot's
> sun8i-h3.dtsi(usb-otg, spdif). Maybe it's worth bumping all the sunxi
> dt's up to the latest revision.The way we deal with it is just to sync what's needed when needed. In this case, sun8i-h3.dtsi. The rest of the DT don't really need to be updated. Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com
signature.asc
Description: PGP signature
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
