From: Marcus Cooper <codekip...@gmail.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using
the SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, a dual
colour LED, an IR receiver and an optical S/PDIF connector.
Signed-off-by: Marcus Cooper <codekip...@gmail.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun8i-h3-beelink-x2.dts | 155 +++++++++++++++++++++++++++++++++++
board/sunxi/MAINTAINERS | 5 ++
configs/beelink_x2_defconfig | 18 ++++
4 files changed, 179 insertions(+)
create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
create mode 100644 configs/beelink_x2_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 9540ba4313..f899cef7ac 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -335,6 +335,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \
dtb-$(CONFIG_MACH_SUN8I_H3) += \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
+ sun8i-h3-beelink-x2.dtb \
sun8i-h3-libretech-all-h3-cc.dtb \
sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-lite.dtb \
diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
b/arch/arm/dts/sun8i-h3-beelink-x2.dts
new file mode 100644
index 0000000000..43f67eb8db
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
@@ -0,0 +1,155 @@
+/*
+ * Copyright (C) 2017 Marcus Cooper <codekip...@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Beelink X2";
+ compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet1 = &sdiowifi;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "beelink-x2:blue:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+
+ red {
+ label = "beelink-x2:red:standby";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ phy = <&phy1>;
+ phy-mode = "mii";
+ allwinner,use-internal-phy;
+ allwinner,leds-active-low;
+ status = "okay";
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ /*
+ * Explicitly define the sdio device, so that we can add an ethernet
+ * alias for it (which e.g. makes u-boot set a mac-address).
+ */
+ sdiowifi: sdio_wifi@1 {
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 362edffc42..1ec7edef13 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -143,6 +143,11 @@ M: Jagan Teki <ja...@amarulasolutions.com>
S: Maintained
F: configs/bananapi_m64_defconfig
+BEELINK X2 BOARD
+M: Marcus Cooper <codekip...@gmail.com>
+S: Maintained
+F: configs/beelink_x2_defconfig
+
COLOMBUS BOARD
M: Maxime Ripard <maxime.rip...@free-electrons.com>
S: Maintained
diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
new file mode 100644
index 0000000000..0b9386609e
--- /dev/null
+++ b/configs/beelink_x2_defconfig
@@ -0,0 +1,18 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=624
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_SUN8I_EMAC=y
+CONFIG_SY8106A_POWER=y
+CONFIG_USB_EHCI_HCD=y
--
2.16.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
