Hi Neil, On 22 November 2017 at 06:25, Neil Armstrong <narmstr...@baylibre.com> wrote: > This adds platform code for the Khadas VIM board based on a > Meson GXL (S905X) SoC with the Meson GXL configuration. > > This initial submission supports UART, MMC/SDCard and Ethernet with the > Internal RMII PHY. > > The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13 > stable tree as of 4.13.8. > > Signed-off-by: Neil Armstrong <narmstr...@baylibre.com> > --- > arch/arm/dts/Makefile | 3 +- > arch/arm/dts/meson-gxl-s905x-khadas-vim.dts | 137 > ++++++++++++++++++++++++++++ > arch/arm/mach-meson/Kconfig | 9 ++ > board/amlogic/khadas-vim/Kconfig | 12 +++ > board/amlogic/khadas-vim/MAINTAINERS | 6 ++ > board/amlogic/khadas-vim/Makefile | 8 ++ > board/amlogic/khadas-vim/README | 96 +++++++++++++++++++ > board/amlogic/khadas-vim/khadas-vim.c | 48 ++++++++++ > configs/khadas-vim_defconfig | 35 +++++++ > include/configs/khadas-vim.h | 21 +++++ > 10 files changed, 374 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/dts/meson-gxl-s905x-khadas-vim.dts > create mode 100644 board/amlogic/khadas-vim/Kconfig > create mode 100644 board/amlogic/khadas-vim/MAINTAINERS > create mode 100644 board/amlogic/khadas-vim/Makefile > create mode 100644 board/amlogic/khadas-vim/README > create mode 100644 board/amlogic/khadas-vim/khadas-vim.c > create mode 100644 configs/khadas-vim_defconfig > create mode 100644 include/configs/khadas-vim.h
Reviewed-by: Simon Glass <s...@chromium.org> Please see below. > diff --git a/board/amlogic/khadas-vim/README b/board/amlogic/khadas-vim/README > new file mode 100644 > index 0000000..add6a29 > --- /dev/null > +++ b/board/amlogic/khadas-vim/README > @@ -0,0 +1,96 @@ > +U-Boot for Khadas VIM > +======================= > + > +Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Tomato > +Technology Co., Ltd with the following specifications: > + > + - Amlogic S905x ARM Cortex-A53 quad-core SoC @ 2GHz > + - ARM Mali 450 GPU > + - 2GB DDR3 SDRAM > + - 10/100 Ethernet > + - HDMI 2.0 4K/60Hz display > + - 40-pin GPIO header > + - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG > + - 8GB/16GBeMMC > + - microSD > + - SDIO Wifi Module, Bluetooth > + - Two channels IR receiver > + > +Currently the u-boot port supports the following devices: > + - serial > + - eMMC, microSD > + - Ethernet > + > +u-boot compilation U-Boot > +================== > + > + > export ARCH=arm > + > export CROSS_COMPILE=aarch64-none-elf- > + > make khadas-vim_defconfig > + > make > + > +Image creation > +============== > + > +Amlogic doesn't provide sources for the firmware and for tools needed > +to create the bootloader image, so it is necessary to obtain them from > +the git tree published by the board vendor: > + > + > wget > https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz > + > wget > https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz > + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz > + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz > + > export > PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH > + > git clone https://github.com/khadas/u-boot -b Vim vim-u-boot > + > cd vim-u-boot > + > make kvim_defconfig > + > make > + > export FIPDIR=$PWD/fip > + > +Go back to mainline U-Boot source tree then : > + > mkdir fip > + > + > cp $FIPDIR/gxl/bl2.bin fip/ > + > cp $FIPDIR/gxl/acs.bin fip/ > + > cp $FIPDIR/gxl/bl21.bin fip/ > + > cp $FIPDIR/gxl/bl30.bin fip/ > + > cp $FIPDIR/gxl/bl301.bin fip/ > + > cp $FIPDIR/gxl/bl31.img fip/ > + > cp u-boot.bin fip/bl33.bin > + > + > $FIPDIR/blx_fix.sh \ > + fip/bl30.bin \ > + fip/zero_tmp \ > + fip/bl30_zero.bin \ > + fip/bl301.bin \ > + fip/bl301_zero.bin \ > + fip/bl30_new.bin \ > + bl30 > + > + > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 > + > + > $FIPDIR/blx_fix.sh \ > + fip/bl2_acs.bin \ > + fip/zero_tmp \ > + fip/bl2_zero.bin \ > + fip/bl21.bin \ > + fip/bl21_zero.bin \ > + fip/bl2_new.bin \ > + bl2 > + > + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin > + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img > + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin > + > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output > fip/bl2.n.bin.sig > + > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ > + --output fip/u-boot.bin \ > + --bl2 fip/bl2.n.bin.sig \ > + --bl30 fip/bl30_new.bin.enc \ > + --bl31 fip/bl31.img.enc \ > + --bl33 fip/bl33.bin.enc > + > +and then write the image to SD with: > + > + > DEV=/dev/your_sd_device > + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 > seek=1 > + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 This bit (from 'got back to U-Boot sources') seems like a job for binman, as I just mentioned in the other patch. Regards, Simon _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot