On 09/22/2017 02:20 PM, Clément Péron wrote:
Sorry these are my local commits you can find them here :
https://patchwork.ozlabs.org/patch/765992/
https://patchwork.ozlabs.org/patch/765996/
https://patchwork.ozlabs.org/patch/765997/
https://patchwork.ozlabs.org/patch/765998/
Hi,
just tested this on my cyclone5 board, but unfortunately without success.
---
U-Boot SPL 2017.09-00354-g824def8 (Sep 27 2017 - 06:47:19)
(....)
Hit any key to stop autoboot: 0
=> sf probe
SF: Detected n25q512 with page size 256 Bytes, erase size 64 KiB, total
64 MiB
### ERROR ### Please RESET the board ###
----
same behavior as before.
But the good news are, that a colleague of mine successfully brought up
a custom board with this patch.
Prior he had trouble in SPL accessing the flash.
I will poke him to give some "tested-by" credits on this.
cheers,
Hannes
2017-09-22 14:12 GMT+02:00 Clément Péron <peron.c...@gmail.com>:
Hi,
I got also somme issue with my QSPI on CycmoneV and u-boot 2017.07
I cherry-picked commits from Jason Rush :
b90ce1c29023abe730d2b4174294bdc09acef3e0
836a0278476be94c95ff084f81c2302fc5c0265c
b0eac7e0d1e4817388543b58d30b322d0bac49a8
Also i forgot to put the
"u-boot,dm-pre-reloc;" in my device tree in the qspi node.
Now my QSPI is working fine except the sf unlock / lock
I have remove the "clear BP# bits" in the mtd/spi/spi_flash.c
Hope this can help you
Regards,
Clement
2017-09-06 8:10 GMT+02:00 Hannes Schmelzer <han...@schmelzer.or.at>:
Hi Jagan,
On 09/04/2017 08:22 AM, Hannes Schmelzer wrote:
"U-Boot" <u-boot-boun...@lists.denx.de> schrieb am 01.09.2017 16:39:03:
<han...@schmelzer.or.at> wrote:
Hi Eldor,
just found your post in the mailinglist.
https://lists.denx.de/pipermail/u-boot/2016-December/276491.html
Reason why i'm searched there is, that i've now excactly same problem
as
you.
Can you give some details, issue came-up while 'sf probe' or 'sf read' ?
Hi Jagan,
please have a look into the weblink to the denx mailing list server.
I have basically same trouble as eldor reported the days ago.
A simple 'sf probe' ends up in a
### ERROR ### Please RESET the board ###
Interesting detail is, that the information about the flash (type, size,
...) is printed out quite before the "hang".
On wednesday i have the next time-slot to access the socfpga devkit board.
So i could bring in more details if necessary.
as told few days ago, i've now again access to my socfpga devkit board.
Here comes the console output:
---
U-Boot SPL 2017.09-rc4-00023-g84a4206 (Sep 06 2017 - 08:02:35)
/home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: Preparing to
start memory calibration
/home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: CALIBRATION
PASSED
/home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: Calibration
complete
Trying to boot from MMC1
spl: partition error
U-Boot 2017.09-rc4-00023-g84a4206 (Sep 06 2017 - 08:02:35 +0200)
CPU: Altera SoCFPGA Platform
FPGA: Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
BOOT: SD/MMC Internal Transceiver (3.0V)
Watchdog enabled
I2C: ready
DRAM: 1 GiB
MMC: dwmmc0@ff704000: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Altera SOCFPGA Cyclone V SoC Development Kit
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.
Hit any key to stop autoboot: 0
=> sf probe
SF: Detected n25q512 with page size 256 Bytes, erase size 64 KiB, total 64
MiB
### ERROR ### Please RESET the board ###
----
Afterwards the board does some reset (about 20sec. later).
cheers,
Hannes
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
